• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.03a
• /
• pp.75-84
• /
• 1998

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1359-1364
• /
• 2008

It is well known that the standard penetration test (SPT) has been used in all over the world to get geotechnical properties of the ground. However, it is difficult to apply the SPT to the dense sand, gravel, weathered rock, etc. For the application of the SPT in these grounds, it is necessary to change in the diameter and the impact energy of the SPT. For the improvement of site investigation technology, Large Penetration Testing device (KICT-type LPT) was developed and applied to the in situ condition. The drop height and weight of the hammer in developed system were decided as 760mm and 150kg, respectively. And the developed sampler has the inner diameter of 63 mm and the length of 500 mm with the adjustment of energy ratio to the SPT of 1.5. In this study, the performance of KICT-type LPT was evaluated by using a calibration chamber system and pile driving analyzer (PDA)

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.10a
• /
• pp.241-264
• /
• 2001

Due to the variation of equipments and test procedure, level of energy transferred to split spoon sampler varies and thus measured N value. Since the properties and parameters are estimated from empirical correlations related to N value, the correction of N value with respect to specific energy level is essential. Factors affecting N value are discussed and the results of previous studies on energy correction of SPT N value is reviewed. Part of results from joint research works with KHC are presented and the range of energy levels for the hammer and release system typically used in Korea is suggested.

• Geotechnical Engineering
• /
• v.8 no.1
• /
• pp.59-66
• /
• 1992

The SPT If value has been known to be influenced by various factors, among which the actually delivered energy level of the falling ram has the most significant effect. If N values of different energy levels are to be applied in the general analysis which is based on N values of standard energy levee the safety of the foundation might be in danger or the design might be overestimated. In this study the actual falling velocity of the ram has been measured so that the energy level could be estimated. The results Indicated that the energy level should be considered in the analysis or the design in this country, since the measured values are different from the internationally accepted scandard value, N60

• Journal of the Korean Geotechnical Society
• /
• v.16 no.3
• /
• pp.119-129
• /
• 2000

국내에서 가장 많이 사용되는 현장조사방법인 표준관입시험의 결과로 얻어지는 N값에 대해 가장 큰 영향을 미치는 롯드 에너지 전단률(깽 Energy Ratio)을 지반조건이 상이한 3개 현장에서 항타분석기(Pile Driving Analyzer)를 이용하여 실측하였다. 에너지 전달률에 영향을 미치는 요인들 중엣 해머의 종류, 로프의 상태, 자아틀에 감은 횟수 등의 조건을 달리하여 롯드 에너지 전달률에 미치는 영향을 측정/분석하였다. 실험결과에 의하면 도넛해머, 안전해머, 개량형 도넛해머(Modified Automatic Donut Hammer)는 롯드에너지 전달률이 각각42%, 66%, 57% 정도로 측정되었으며 로프의 상태와 자아틀에 감은 횟수는 상대적으로 영향이 적은 것으로 측정되었다. 실험결과를 바탕으로 실측된 N값을 해머의 이론적 위치에너지의 60%에 해당하는 에너지가 롯드에 전달되었을 때의 N값(N60)으로 변환하기 위한 식을 제안하였다.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.3-9
• /
• 2005

In order to obtain more reliable data for the information on the ground, a new site Investigation method is proposed, in which seismic waves (S-waves) generated by the Swedish Ram Sounding Test (SRS) are used. It is indicated that the energy transferred from the hammer to the rod in SRS's is much more stable, compared to SPT's. A series of SRS with measurements of seismic waves at the ground surface were carried out to clarify the characteristics of seismic wave propagation in the ground. As the results of comparison between seismic S-wave amplitudes and $N_d$ (blow count for 20 cm penetration in SRS), it was found that amplitudes of S-waves generated by SRS correlate well with $N_d$. The amplitude of the S-wave is thought to be more adequate parameter for the soil strength and rigidity than $N_d$.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.910-921
• /
• 2004

In this study, the pilot tests on the reclaimed land were performed in order to find the suitable construction method with dynamic compaction Type I, Type II at different dynamic energy and hydraulic hammer compaction. The estimation of the compaction through the various pilot tests was performed by the CPT-qc, SPT-N and field density tests. As the result of the pilot tests, it shows that the dynamic compaction method is better than the hydraulic hammer compaction method in the effect of the ground improvement, especially dynamic compaction Type I is much superior to others. When it comes to method for measuring the intensity of the ground, the value of the cone penetration test-resistance(qc) is much suitable for the ground. Besides, the standards for the compaction control, which showed that over 10Mpa at 0 through 5meters in the upper layer and 7Mpa at 5 through 8meters in the lower layer in the CPT-qc, could be found without discrimination of the upper road and lower road on the reclaimed land. And it also found that the intensity of the reclaimed land gets back to the original status in about 10 through 15 days.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.10a
• /
• pp.293-298
• /
• 2001

N-value is usually used to assume the displacement depth of embankment on the soft marine clay. But N-value of the soft marine clay tend to underestimate unlike overestimating of general cases. In general case, if the length of rod is more long then N-value is more large because it is under the influence of energy loss of hammer blow. So it is reasonable to correct N-value down. But in the case of soft marine clay, N-value must not be correct down. Especially to assume the displacement depth of embankment on the soft marine clay, it must be used laboratory test results or CPT, Vane Test than N-value. In this study, it is compared with two field cases that design displacement method of embankment.