• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.57-63
• /
• 2005

The effects of an urea injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine were investigated with the parameters such as urea-SCR(Selective Catalytic Reduction) and EGR system. The urea quantity was controlled by NOx quantity and MAF(Manifold Air Flow). The urea injection quantity can be controlled with the urea syringe pump, precisely. The effects of NOx reduction for the urea-SCR system were investigated with and without ECR engine, respectively. It was concluded that the SUF(Stoichiometric Urea Flow) is calculated and the NOx results are visualized with engine speed and load. Furthermore, the NOx map is made from this experimental results. It was suggested, therefore, that NOx reduction effects of the urea-SCR system without the EGR engine were better than that with the EGR engine except of low load and low speed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.458-465
• /
• 1998

This paper presents an inverter-driven induction motor used as the traction motor for a high speed drive system that is required safety, reliability and performance and so on, In the respect of traction motor design, it is mainly showed the weight reduction inclination and characteristic investigation due to V/f driving pattern variation of inverter. Particularly, the reduction of V/f ratio pattern effects on the weight of traction motor and badly on the increase of phase current of traction motor in starting point. This method of weight reduction design have to be reached the decision with not only motor but also the consideration of inverter system because of the heat capacity, weight and material cost of inverter according to the increase of current.

• 반도체디스플레이기술학회지
• /
• 제11권2호
• /
• pp.33-38
• /
• 2012

The wafer positioning robot in the semiconductor industry is required to operate at high speed for the improvement of productivity. The residual vibration caused by the high speed of the wafer positioning robot, however, makes the life of the robot shorter and the cycle time longer. In this study, the input shaping and the path of the system are designed for the reduction of the residual vibration and the improvement of the cycle time. The followings are the process for the reduction and the improvement; 1) System modeling of the wafer positioning robot, 2) Verification of dynamic characteristics of the wafer positioning robot, 3) Input shaping plan using impulse response reiteration, 4) Simulation test using SIMULINK program, 5) Analysis of result.

• 한국ITS학회 논문지
• /
• 제22권1호
• /
• pp.93-102
• /
• 2023

본 연구는 운전자에게 차량속도와 횡단보도 인근 보행자 존재 유무에 대한 정보를 제공하는 차량정보안내시스템의 설치 전·후에 대한 효과평가를 수행했다. 시나리오는 운전자에게 정보를 제공하지 않는 경우(S1), 차량주행속도만 제공하였을 경우(S2), 횡단보도에 보행자의 존재 유무와 차량주행속도를 모두 제공하였을 경우(S3) 등 3가지로 구성했다. 조사결과 시나리오 S1보다 운전자에게 정보를 제공하는 S2, S3에서 차량의 속도감속률이 약 0.4~0.7km 큰 것으로 나타났다. 또한 시나리오 S3에서 횡단보도 인근에 보행자가 있는 경우에 없는 경우보다 속도 감속률이 0.2km 높아 차량 속도를 더 줄이는 것으로 나타났다. 통계분석 결과에서도 시나리오 3개에 대한 평균 차량의 속도감속률에 차이가 있는 것으로 분석됐고, 보행자가 있는 경우 속도 감속률이 큰 것으로 나타났다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 1999년도 추계 기술심포지움 논문집
• /
• pp.33-36
• /
• 1999

In this paper, we proposed a simultaneous switching noise(SSN) reduction technique in muti-layer beards(MLB) for high-speed digital applications and analyzed them using the Finite Difference Time Domain(FDTD) method. The new method by conductive dielectric substrates reduces SSN couplings and resonances, significantly, which cause series malfunctions in the modem high-speed digital applications.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 1999년도 학술대회논문집-국제 전기방전 및 플라즈마 심포지엄 Proceedings of 1999 KIIEE Annual Conference-International Symposium of Electrical Discharge and Plasma
• /
• pp.162-167
• /
• 1999

In Auxiliary block of High speed train Power factor correction and Harmonics reduction is very important issue for efficient energy transport. The GTO-equipped PWM converter is used for traction untill resently. but the rising power capability of IGBTs resently allows to build IGBT-equipped PWM converter with a considerably increases switching frequency. In this paper presents switching pattern, control method, operation mode and tuned filter to reduce dc link voltage ripple for paralleled converter.

• 한국소음진동공학회논문집
• /
• 제13권5호
• /
• pp.357-363
• /
• 2003

There have been lots of studies on noise transmission analysis and noise reduction In ducts. In order to reduce the noise transmission in ducts. active noise cancellation techniques have often been employed and a rotation shaft with blades has sometimes been suggested. These Ideas were not successfully commercialized because of the limitation of real life such as size or application difficulties. This study investigated how a rotational shaft with blades could reduce the noise transmission in a duct. To do so, an assembly of the shaft and the $haft housing was built In the middle of a duct. and the clearance between the blades and the housing was 0.2 mm. The noise reduction was experimentally evaluated with respect to the number of blades. the rotation speed, and the rotation or stop. This paper showed that the noise reduction resulted in about 14∼19 dBA regardless of the three test conditions only If the blades always blocked the duct. And. the noise reduction increased due to the higher number of blades and the lower speed of the shaft.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.443-444
• /
• 2011

This paper discusses a model order reduction for large order rotor dynamics systems results from the finite element discretization. Typical rotor systems consist of a rotor, built-on parts, and a support system, and require prudent consideration in their dynamic analysis models because they include unsymmetric stiffness, localized nonproportional damping and frequency dependent gyroscopic effects. When the finite element model has a very large number of degrees of freedom because of complex geometry, repeated dynamic analyses to investigate the critical speeds, stability, and unbalanced response are computationally very expensive to finish within a practical design cycle. In this paper, the Krylov-based model order reduction via moment matching significantly speeds up the dynamic analyses necessary to check eigenvalues and critical speeds of a Nelson-Vaugh rotor system. With this approach the dynamic simulation is efficiently repeated via a reduced system by changing a running rotational speed because it can be preserved as a parameter in the process of model reduction. The Campbell diagram by the reduced system shows very good agreement with that of the original system. A 3-D finite element model of the Nelson-Vaugh rotor system is taken as a numerical example to demonstrate the advantages of this model reduction for rotor dynamic simulation.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권3호
• /
• pp.737-748
• /
• 2014

Increasing amounts of ships exhaust gases emitted worldwide forced the International Maritime Organization to issue some restricted maritime legislation for reducing the adverse environmental impacts arising from such emissions. Consequently, ships emission reduction became one of the technical and economical challenges that facing the ships, operators. The present paper addresses the different strategies that can be used to reduce those emissions, especially nitrogen oxides and sulfur oxides. The strategies included: applying reduction technologies onboard, using of alternative fuels, and follows one of fuel saving strategies. Using of selective catalytic reduction and sea water scrubbing appeared as the best reduction technologies onboard ships. Moreover, among the various proposed alternative fuels, natural gas, in its liquid state; has the priority to be used instead of conventional fuels. Applying one of those strategies is the matter of ship type and working area. As a numerical example, the proposed methods were investigated at a high-speed craft operating in the Red Sea area between Egypt and the Kingdom of Saudi Arabia. The results obtained are very satisfactory from the point of view of environment and economic issues, and reflected the importance of applying those strategies.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.409-410
• /
• 2012

Speed output has ripple such as periodic torque ripple if load torque with periodic ripple was injected in AC motor. In this paper, it is proposed method to reduce speed ripple through novel speed control method. It replaces algorithm to compensate torque ripple. Proposed method demonstrated through simulation using MATLAB SIMULINK.