• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.111-115
• /
• 2011

Surface Texturing is an essential process for high efficiency in multi-crystalline silicon solar cell. In order to reduce the reflectivity, there are two major methods; proper surface texturing and anti-reflection coating. For texturization, wet chemical etching is a typical method for multi-crystalline silicon. The chemical solution for wet etching consists of HF, $NHO_3$, DI and $CH_3COOH$. We carried out texturization by the change of etching time like 15sec, 30sec, 45sec, 60sec and measured the reflectivity of textured wafers. As making the silicon solar cells, we obtained the conversion efficiency and relationship between texturing condition and solar cell characteristics. The reflectivity from 300nm to 1200nm was the lowest with 15 sec texturing time and 60 sec texturing time showed almost same reflectivity as bare one. The 45 sec texturing time showed the highest conversion efficiency.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2011년도 추계학술대회
• /
• pp.419-422
• /
• 2011

본 논문에서는 초저전력 어플리케이션을 위한 이중입력 자가 전력관리 시스템을 제안한다. 자가 발전 시스템의 전력 공급원으로는 PZT와 solar cell소자를 병합하여 사용한다. 제한된 전력관리 회로는 solar cell 출력 전압을 승압하기 위한 charge pump 회로, PZT의 출력을 DC로 변환하기 위한 rectifier, 수확된 에너지를 병합 및 관리하기 위한 전력관리회로로 구성된다. 설계된 회로는 CMOS 0.18um technology를 이용하여 성능을 검증하였다. 설계된 회로의 칩 면적은 $295um{\times}275um$ 이다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2006년도 추계학술발표회 초록집
• /
• pp.4-5
• /
• 2006

This paper represents modeling and optimization techniques for solar cell process on single-crystalline float zone (FZ) wafers with high efficiency; There were the four significant processes : i)emitter formation by diffusion, anti-reflection-coating (ARC) with silicon nitride using plasma-enhanced chemical vapor deposition (PECVD); iii)screen-printing for front and back metallization; and iv)contact formation by firing. In order to increase the performance of solar cells, the contact formation process is modeled and optimized. This paper utilizes the design of experiments (DOE) in contact formation to reduce process time, fabrication costs. The experiments were designed by using central composite design which is composed of $2^4$ factorial design augmented by 8 axial points with three center points. After contact formation process, the efficiency of the solar cell is modeled using neural networks. This model is used to analyse the characteristics of the process, and to optimize the process condition using genetic algorithms (GA). Finally, find optimal recipe for solar cell efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.222-224
• /
• 2006

A non-vacuum process for $Cu(In,Ga)Se_2$ (CIGS) thin film solar cells from nanoparticle precursors was described in this work CIGS nanoparticle precursors was prepared by a low temperature colloidal route by reacting the starting materials $(CuI,\;InI_3,\;GaI_3\;and\;Na_2Se)$ in organic solvents, by which fine CIGS nanoparticles of about 20nm in diameter were obtained. The nanoparticle precursors were mixed with organic binder material for the rheology of the mixture to be adjusted for the doctor blade method. After depositing the mixture of CIGS with binder on Mo/glass substrate, the samples were preheated on the hot plate in air to evaporate remaining solvents ud to burn the organic binder material. Subsequently, the resultant (porous) CIGS/Mo/glass simple was selenized in a two-zone Rapid Thermal Process (RTP) furnace in order to get a solar ceil applicable dense CIGS absorber layer. Complete solar cell structure was obtained by depositing. The other layers including CdS buffer layer, ZnO window layer and Al electrodes by conventional methods. The resultant solar cell showed a conversion efficiency of 0.5%.

• Korean Journal of Chemical Engineering
• /
• 제35권12호
• /
• pp.2430-2441
• /
• 2018

Selenium (Se)-rich binary Cu-Se and In-Se nanoparticles (NPs) were synthesized by a modified heat-up method at low temperature ($110^{\circ}C$) using the gum exudates from a cherry blossom tree. Coating of CISe absorber layer was carried out using Se-rich binary Cu-Se and In-Se NPs ink without the use of any external binder. Our results indicated that the gum used in the synthesis played beneficial roles such as reducing and capping agent. In addition, the gum also served as a natural binder in the coating of CISe absorber layer. The CISe absorber layer was integrated into the solar cell, which showed a power conversion efficiency (PCE) of 0.37%. The possible reasons for low PCE of the present solar cells and the steps needed for further improvement of PCE were discussed. Although the obtained PCE is low, the present strategy opens a new path for the fabrication of eco-friendly CISe NPs solar cell by a relatively chief non-vacuum method.

• 한국전기전자재료학회논문지
• /
• 제36권1호
• /
• pp.16-22
• /
• 2023

In a solar cell, degradation refers to the decrease in performance parameters caused by defects originated due to various causes. During the fabrication process of solar cells, degradation is generally related to the processes such as passivation or firing. There exist sources of many types of degradation; however, the exact cause of Light and elevated Temperature Induced Degradation (LeTID) is yet to be determined. It is reported that the degradation and the regeneration occur due to the recombination of hydrogen and an arbitrary substance. In this paper, we report the deposition of Al₂O₃ and SiN_X on silicon wafers used in the Passivated Emitter and Rear Contact (PERC) solar structure and its degradation pattern. A higher degradation rate was observed in the sample with single layer of Al₂O₃ only, which indicates that the degradation is affected by the presence or the absence of a passivation thin film. In order to alleviate the degradation, optimization of different steps should be carried out in consideration of degradation in the solar cell fabrication process.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.91.2-91.2
• /
• 2010

The use of plated front contact for metallization of silicon solar cell may alternative technologies as a screen printed and silver paste contact. This technologies should allow the formation of contact with low contact resistivity a high line conductivity and also reduction of shading losses. The better performance of Ni/Cu contacts is attributed to the reduced series resistance due to better contact conductivity of Ni with Si and subsequent electroplating of Cu on Ni. The ability to pattern narrower grid lines for reduced light shading combined with the lower resistance of a metal silicide contact and improved conductivity of plated deposit. This improves the FF as the series resistance is deduced. This is very much required in the case of low concentrator solar cells in which the series resistance is one of the important and dominant parameter that affect the cell performance. A selective emitter structure with highly dopes regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing. This paper using selective emitter structure technique, fabricated Ni/Cu plating metallization cell with a cell efficiency of 17.19%.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.48.1-48.1
• /
• 2010

단결정 실리콘 태양전지 제조 공정이 진행되는 과정에서 각종 오염물에 의해 표면이 오염된다. 태양전지의 효율 개선을 위한 표면 texturing 공정은 주로 wet etch을 주로 사용한다. Wet etch 공정 시 주로 사용되는 KOH 용액은 texturing 후 실리콘 웨이퍼 표면에 K+ 이온을 남기고 이는 태양전지 표면에서의 불순물로 작용하여 효율을 저하시키는 요인이 된다. 이를 제거하기 위해 불산 및 오존에 의한 세정 공정이 추가로 필요로 하게 된다. 이러한 공정을 최소화 하며 잔존하는 알칼리 금속도 제거하기 위해, etchant로 알카리 용액이 아닌 ethylenediamine을 사용하여 texturing 후 KOH 용액과 비교해 보았다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.403.1-403.1
• /
• 2016

일반적으로 실리콘 태양전지의 표면 텍스쳐링 공정방식은 습식 텍스쳐링 방식과 건식 텍스쳐링 방식 2가지로 나뉘어진다. 하지만 현재 습식 텍스쳐링 방식의 경우 Solution을 사용하기 때문에 폐용액으로 인한 환경오염 및 Wafer 오염과 같은 단점을 가지고 있다. 또한 건식 텍스쳐링 방식의 경우는 진공 상태에서 진행되므로 높은 유지 비용이 가장 큰 단점으로 대두 되고 있다. 그러므로 기존의 방식과 다르게 진공을 사용하지 않는 대기압 플라즈마 소스를 텍스쳐링 공정에 적용하였다. 본 연구에서는 대기압 플라즈마 소스로 식각한 Wafer의 반사율을 가스 종류와 유량별 측정하여 분석하였다. 측정된 반사율을 통해 대기압 플라즈마 소스가 텍스쳐링 공정에 적용할 수 있는지 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.419-419
• /
• 2016

High efficiency silicon solar cell requires the textured front surface to reduce reflectance and to improve the light trapping. In case of mono-crystalline silicon solar cell, wet etching with alkaline solution is widespread. However, the alkali texturing methods are ineffective in case of multi-crystalline silicon wafer due to grain boundary of random crystallographic orientation. The acid texturing method is generally used in multi-crystalline silicon wafer to reduce the surface reflectance. However the acid textured solar cell gives low short-circuit current due to high reflectivity while it improves the open-circuit voltage. To reduce the reflectivity of multi-crystalline silicon wafer, double texturing method with combination of acid and reactive ion etching is an attractive technical solution. In this paper, we have studied to optimize RIE experimental condition with change of RF power (100W, 150W, 200W, 250W, 300W). During experiment, the gas ratio of SF6 and O2 was fixed as 30:10.