• Clean Technology
• /
• v.20 no.2
• /
• pp.108-115
• /
• 2014

Various metal chlorides and acid catalysts in ionic liquid solvent were investigated to directly convert cellulose into 5-hydroxymethylfurfural (5-HMF). Metal chlorides containing Sn(II), Zn(II), Al(III), Fe(III), Cu(II), and Cr(III) were used and acidic ionic liquid immobilized on silica gel as an acid catalyst and commercial acid catalysts (sulfuric acid, chloric acid, Amberlyst-15,DOWEX50x8) were used for comparison studies. The acid strength and amount of acid catalysts were probed with Hammett indicator. The selectivity and yield of 5-HMF were determined with reaction temperature, reaction time and catalyst ratio. A catalyst containing $CrCl_3-6H_2O$ and $SiO_2-[ASBI]HSO_4$ showed the highest selectivity and it was found that this catalyst had higher activity than commercial solid acid catalysts such as Amberlyst-15 and DOWEX50x8. The selectivity of 5-HMF appeared to be mainly dependent on the acid strength and catalyst ratio, it was found that levulinic acid was produced from 5-HMF by rehydration.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2001

We investigate the via-size dependance of as-electroplated- and reflow-bump shapes for realizing both high-density and high-aspect ratio of solder bump. The solder bump is fabricated by subsequent processes as follows. After sputtering a TiW/Al electrode on a 5-inch Si-wafer, a thick photoresist for via formation it obtained by multiple-codling method and then vias with various diameters are defined by a conventional photolithography technique using a contact alinger with an I-line source. After via formation the under ball metallurgy (UBM) structure with Ti-adhesion and Cu-seed layers is sputtered on a sample. Cu-layer and Sn/pb-layer with a competition ratio of 6 to 4 are electroplated by a selective electroplating method. The reflow-bump diameters at bottom are unchanged, compared with as-electroplated diameters. As-electroplated- and reflow-bump shapes, however, depend significantly on the via size. The heights of as-electroplated and reflow bumps increase with the larger cia, while the aspect ratio of bump decreases. The nearest bumps may be touched by decreasing the bump pitch in order to obtain high-density bump. The touching between the nearest bumps occurs during the overplating procedure rather than the reflowing procedure because the mushroom diameter formed by overplating is larger than the reflow-bump diameter. The arrangement as zig-zag rows can be effective for realizing the flip-chip-interconnect bump with both high-density and high-aspect ratio.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.397-404
• /
• 2012

In this research, a numerical study was carried out on the mixing and flow characteristics of a vane-type static mixer for the reduction of $NO_x$ in the SCR systems from the diesel exhaust environments. The mixer was located at a distance of 57 times the pipe diameter away from the inlet. The analyses were performed by changing various parameters such as vane angles, blockage ratio, and location of the vane. Flow characteristics through the mixer were characterized by the uniformity index, swirl number, and pressure drop. The results show that uniformity index, pressure coefficient and swirl number are substantially influenced by the vane angle, blockage ratio and position of the vane of the mixer. In particular, the swirl number was increased when the vane was located near the pipe wall, or the vane angle was increased or scale was extended.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.245-245
• /
• 2012

차세대 디스플레이로 각광받고 있는 AMOLED에 대한 관심이 높아짐에 따라 구동 소자의 연구가 활발히 이루어지고 있다. 산화물 반도체 박막 트랜지스터는 비정질 실리콘 박막 트랜지스터에 비해 100 $cm^2$/Vs 이하의 높은 이동도와 우수한 전기적 특성으로 AMOLED 구동 소자로서 학계에서 입증되어왔고, 현재 여러 기업에서 산화물 반도체를 이용한 박막 트랜지스터 제작 연구가 활발히 이루어지고 있다. 본 연구는 열처리 조건을 가변하여 제작한 산화물 반도체 박막 트랜지스터의 전기적 특성 분석을 목적으로 한다. 실리콘 기판에 oxidation 공정을 이용하여 SiO2 100 nm, DC스퍼터링을 이용하여 ITZO (Indium-Tin-Zinc Oxide) 산화물 반도체 박막 50 nm, 증착된 산화물 반도체 박막의 열처리 후, evaporation을 이용하여 source/drain 전극 Ag 150 nm 증착하여 박막 트랜지스터를 제작하였다. 12 sccm의 산소유량, 1시간의 열처리 시간에서 열처리 온도 $400^{\circ}C$, $200^{\circ}C$의 샘플은 각각 이동도 $29.52cm^2/V{\cdot}s$, $16.15cm^2/V{\cdot}s$, 문턱전압 2.61 V, 6.14 V, $S{\cdot}S$ 0.37 V/decade, 0.85 V/decade, on-off ratio 5.21 E+07, 1.10 E+07이었다. 30 sccm의 산소유량, 열처리 온도 $200^{\circ}C$에서 열처리 시간 1시간, 1시간 30분 샘플은 각각 이동도 $12.27cm^2/V{\cdot}s$, $10.15cm^2/V{\cdot}s$, 문턱전압 8.07 V, 4.21 V, $S{\cdot}S$ 0.89 V/decade, 0.71 V/decade, on-off ratio 4.31 E+06, 1.05 E+07이었다. 산화물 반도체의 열처리 효과 분석을 통하여 높은 열처리 온도, 적은 산소의 유량, 열처리 시간이 길수록 이동도, 문턱전압, $S{\cdot}S$의 산화물 박막 트랜지스터 소자의 전기적 특성이 개선되었다.

• Korean Journal of Ichthyology
• /
• v.5 no.1
• /
• pp.85-95
• /
• 1993

Sexual dimorphism of the matured chum salmon, Onchorhynchus keta, have been studied based on biometrical measurements and osteological characters. Male chum salmon has an elongated and hooked upper jaw and canine-like teeth on the upper and lower jaw. The ratios of snout length (SnL) and upper jaw length (UJ) to head length of male were larger than those of the female, whereas eye diameter (ED) and postorbital part of head (CK) of the male were smaller than those of the female's. The ratios of body depth, caudal peduncle depth, anal fin length and adipose fin length to the standard length (PBL) of the male were also larger than those of the female. On sexual dimolrphism was detected in number of fin rays, gill rakers and pyloric ceaca, where as number of lateral line scales and caudal vertebrae of the female was larger than those of the male. Glossohyal and vomer bones has no sexual difference. The ratio of width to length of supraethmoid bone of the male was larger than that of the female. The ratio of frontal part to posterior part of parasphenoid bone of the male was smaller than that of the female.

• Journal of radiological science and technology
• /
• v.40 no.2
• /
• pp.269-274
• /
• 2017

In this research, we simulated the elementary star shielding ability using Monte Carlo simulation to apply medical radiation shielding sheet which can replace existing lead. In the selection of elements, mainly elements and metal elements having a large atomic number, which are known to have high shielding performance, recently, various composite materials have improved shielding performance, so that weight reduction, processability, In consideration of activity etc., 21 elements were selected. The simulation tools were utilized Monte Carlo method. As a result of simulating the shielding performance by each element, it was estimated that the shielding ratio is the highest at 98.82% and 98.44% for tungsten and gold.

• Journal of the Korean Institute of Gas
• /
• v.10 no.3 s.32
• /
• pp.34-40
• /
• 2006

This paper presents the optimized design of O-rings with a rectangular groove and dovetails, which are strongly related on the sealing performance of LPG filling unit. The computed results on the optimal design are analyzed by non-linear MARC finite element program with Taguchi method. O-rings with 4 different groove models are analyzed for 3 different elastomeric materials. The design parameters are given to polymer materials, groove depth, groove width, and diameter of O-rings. The FEM computed results showed that the affection ratios of O-ring diameter and material property are the most influential parameter among the groove width, groove depth, and compression ratio. Thus, this paper recommends model III for a rectangular groove and model IV for a dovetail groove with a given gas supply pressure of 1.764 MPa.

• Journal of Korea Multimedia Society
• /
• v.4 no.5
• /
• pp.455-464
• /
• 2001

For future multimedia services, one of the most crucial issues is building an access network that can accommodate multimedia services in subscriber network. The VB5.2 interface of B-ISDN located between an access network and a service node allows dynamic allocation and release of ATM resources. The SG 13 of ITU-T is standardizing the B-BCC protocol, which is sequentially interworked with signaling protocols in the service node. To minimize a connection setup delay of the sequential interworking mode, we proposed the parallel interworking model in which the SN executes simultaneously the connection control protocol of VB5.2 interface and signaling protocol. We simulate two interworking models in terms of a connection setup delay and a completion ratio. The results of simulation show that our proposed parallel interworking model for the VB5.2 interface reduces the setup delay and has the similar completion ratio compared to the sequential interworking model. however, the connection setup delay of parallel interworking model becomes about seven tenths of that of the sequential interworking model and the improvement become larger as the arrival rate increased.

• Journal of ILASS-Korea
• /
• v.11 no.2
• /
• pp.59-68
• /
• 2006

Experimental results of the metal powder production with internal mixing, internal impinging and the atomizer coupled with substrate design are presented in this paper. In a test with internal mixing atomizer, mean powder size was decreased from $37{\mu}m\;to\;23{\mu}m$ for Pb65Sn35 alloy as the gas-to-melt mass ratio was increased from 0.04 to 0.17. The particle size further reduces to $16.01{\mu}m$ as the orifice area is increased to $24mm^2$. The micrograph of the metal powder indicates that very fine and spherical metal powder has been produced by this process. In a test program using the internal impinging atomizers, the mean particle size of the metal powder was decreased from $22{\mu}m\;to\;12{\mu}m$ as the gas-to-melt-mass ratio increased from 0.05 to 0.22. The test results of an atomizer coupled with a substrate indicates that the deposition rate of the molten spray on the substrate is controlled by the diameter of the substrate, the height of the substrate ring and the distance of the substrate from the outlet of the atomizer. This in rum determines the powder production rate of the spraying processes. Experimental results indicate that the deposition rate of the spray forming material decreases as the distance between the substrate and the atomizer increases. For example, the deposition rate decreases from 48% to 19% as the substrate is placed at a distance from 20cm to 40cm. On the other hand, the metal powder production rate and its particle size increases as the subsrate is placed far away from the atomizer. The production of metal powder with mean particle size as low as $3.13{\mu}m$ has been achieved, a level which is not achievable by the conventional gas atomization processes.

• Journal of Oral Medicine and Pain
• /
• v.17 no.2
• /
• pp.37-49
• /
• 1992

80 patients who presented at Wonkwang University Dental Hospital with craniomandibular disorders were collected for this study. To observe the occlusal contact pattern such as contact numbers, contact force and presence or absence of anterior occlusal contact, the author used T-Scan system (Tekscan, Inc, U.S.A.) with are computerized occlusal analysing system. And to study the correlation between craniofacial profile and occlusal contact pattern, cephalogram were also taken, The cephalometric items related to growth pattern, jaw bone relation and denture pattern were measured and analysed according to routine method by computerized program. The obtained data were statistically processed with SPSS/PC+ package about anterior contact pattern and its craniofacial relationship. The obtained results were as follows : 1. In terms of growth pattern, patients without anterior tooth contacts showed a tendency to downward growth of craniofacial profile. The value in this subjects were significantly different from the value of patients with anterior tooth contacts in items of low gonial angle, Jarabak ratio, SN to GoMe angle, FMA, occlusal plane to mandibular plane angle and ramus height. 2. In terms of jaw bone relationship, patients without anterior tooth contacts showed a tendency to backward growth of craniofacial profile. The value of this patients were significantly different from the value of patients with anterior tooth contacts in items of SNB, ANB, mandibular plane to anterior cranial base ratio, SNPo, NAPo and APDI items. 3. But in denture pattern, no statistically significant difference by the presence or absence of anterior tooth contacts were showed between this patients groups. 4. From this study, it could be proposed that anterior open bite in the patients with craniomandibular disorders would be originated from not dental discrepancy but skeletal discrepancy.