• Journal of ILASS-Korea
• /
• v.19 no.3
• /
• pp.123-129
• /
• 2014

A diesel spray overall SMD (Sauter mean diameter) in a spray chamber was simulated with CFD by varying the compression ratio in the spray chamber from 18:1 to 100:1. The gas densities of the spray chambers for the compression ratios of 18:1 and 100:1 were 17.97 and $74.8kg/m^3$, respectively. Standard KIVA-3V code was used for the CFD simulation. Various fuel injection patterns such as single injection, pilot injection and split injection were used for the CFD simulation. Fuel injection pressures for the simulated diesel sprays are 90 and 120 MPa. As the compression ratio increases, the CFD simulated SMD was decreased, which was generally in agreement with previous experimental studies.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.9-21
• /
• 2000

In this study, the characteristics of high-pressure swirl injector have been studied using a commercial CFD code, STAR-CD and experiment to investigate the effect of the length of orifice and swirl port on the spray characteristics. Influences of swirl port angle and initial conditions have also been examined in terms of penetration depth and Sauter`s mean diameter. Computed results of the spray characteristics are compared with experimental results. The results show that the tangential velocity at the nozzle exit decreases, but the axial velocity increases as swirl port angle is increased. Hence, the static flow rate increases, but the initial spray angle decreases with increasing the swirl port angle. It is also shown that the values of the initial SMD used as input data for spray simulation influences the penetration depth and SMD. The spray pattern from the present numerical simulation agrees well with experimental result.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.943-948
• /
• 2000

The Twin-fluid Swirl Nozzles are used in many parts of the industry to produce homogeneous spray. This study is to investigate the effects of outer air swiller and inner water swiller on atomization of liquid.. The experiment was carried out with increasing air-flow rate at constant liquid-flow rate and with changing outer air swiller angle and inner water swiller angle. A Particle Dynamics Analyzer(PDA) was used to measure drop size, mean and ms values of axial velocity, number density and Sauter mean diameter(SMD). The axial mean velocity and SMD of droplets were measured along the center line and radial directions. It was found that the higher air flow-rate resulted in the smaller Sauter mean diameter of liquid spray and the higher axial mean velocity of droplets. This experimental results will be conveniently used for the preliminary design stage of twin-fluid nozzle development.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1529-1538
• /
• 1995

In this study, a liquid sheet type co-axial nozzle has been used to investigate the turbulent atomization characteristics which could result in the experimental data to be used in designing a jet nozzle with high performance. Image processing technique and immersion sampling method were employed to measure droplet size. In atomizing characteristics, droplet size distributions and absolute droplet sizes, SMD(Sauter Mean Diameter) have been investigated in the wide ranges of flow field depending upon the air-water mass ratios. And the comparisons between the present data and the semi-empirical curves have been conducted semi-empirical correlation for SMD has been derived in the present analysis.

• Journal of Biosystems Engineering
• /
• v.35 no.3
• /
• pp.158-162
• /
• 2010

The effect of fuel injection characteristics on engine performance has been known for improving fuel economy and emission reduction. In this study, the spray characteristics of crude palm oil blended fuel with conventional diesel fuel was investigated. The experiments were performed to evaluate the effect of crude palm oil blending ratio and injection pressure on the spray behavior. The droplet size of injected fuel was analyzed through laser diffraction particle analyzer (LDPA). Also, spray atomization characteristics were investigated in terms of Sauter mean diameter (SMD) and droplet distribution at various injection conditions. Fuel containing crude palm oil has different spray pattern on account of the high viscosity. Through those experimental results, we found that the increase of blending ratio made droplet size larger, SMD of biodiesel 100% was increased 30.2% than that of diesel fuel 100% under injection pressure of 60 MPa.

• Journal of ILASS-Korea
• /
• v.1 no.4
• /
• pp.32-39
• /
• 1996

Fuel spray in the MPI gasoline injector and its atomization characteristics are investigated with both macroscopic and microscopic visualization systems. The Bosch injector is inserted into an air-assist spray adapter which is designed to be fabricated and assembled easily. particle motion analysis system is used to measure the SMD of injector, where the assistant air pressure is varied from 0.0 to 1.5bar with fuel pressure 2.8bar. Droplet size decreased with higher air pressure and fine fuel spray with below $60{\mu}m$ of SMD is acquired at the assistant air pressure over 0.5bar.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.51-56
• /
• 2013

This paper describes the atomization characteristics, as well as the velocity and size distribution, of DME spray based on common-rail injection system. To analyze the possibility of using DME fuel as an alternative fuel of diesel, spray atomization characteristics were investigated. For this investigation, two-dimensional phase Doppler analyzer system was used to obtain droplet size and velocity distribution simultaneously. Velocity and droplet size measurements were performed at various injection pressures. Results showed that increasing pressure from 25MPa to 50MPa leads to higher spray droplet velocities and smaller droplet diameter but injection pressure above 40MPa, no signifiant reduction was observed. With the droplet velocity and SMD comparison between diesel and DME fuel, it can be observed that DME has smaller SMD and droplet velocity due to its low surface tension.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.125-128
• /
• 2008

Atomization characteristics of small LRE-injector spray are investigated by using dual-mode phase Doppler anemometry (DPDA). Velocity, size, number density, and volume flux were measured at various injection pressures along the radial distance to make a close inquiry into spatial distribution characteristic of spray droplets. As the injection pressure increases, the velocity, turbulence intensity, number density, and volume flux of spray droplets become higher, whereas the droplet size ($D_{10}$ or $D_{32}$) gets smaller. Also, velocity and volume flux are proportional to Sauter mean diameter (SMD, $D_{32}$).

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.135-138
• /
• 2007

Two-dimensional distribution characteristics on the spray droplets emanating from an injector employed in a liquid-propellant thruster are investigated through dual-mode phase Doppler anemometry (DPDA). Spray-breakup characteristic parameters such as spray droplet velocity, turbulent intensity, Sauter mean diameter (SMD), number density, and volumetric flux are quantified to scrutinize the macroscopic behavior of injector-spray breakup. The present study will be able to contribute to the comprehension for performance features of the thruster in current use and to the design engineering of a brand-new thruster as well.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.17-24
• /
• 2006

This study was performed to figure out spray behavior and fuel atomization characteristics of a piezo-driven injector and a solenoid-driven injector in the common-rail injection system under the same design parameters and test conditions. The process of spray injection was visualized by using the spray visualization system composed of a Nd:YAG laser and an ICCD camera. The atomization characteristics were investigated in terms of axial mean velocity, Sauter mean diameter(SMD) and droplet distributions obtained from a phase Doppler particle analyzer system. Compared with solenoid-driven injector, the piezo-driven injector has short injection delay and reaches quickly to the maximum injection value. Spray tip penetration shows some difference, however, spray angle of piezo-driven injector is wider than that of solenoid-driven injector. Sauter mean diameter of piezo-driven type injector is smaller than that of solenoid-driven type.