• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.3
• /
• pp.257-264
• /
• 2017

For the safe disposal of intermediate level radioactive waste according to the Nuclear Safety and Security Commission's notice and KORAD's management plan for low and intermediate level radioactive waste, the disposal concentration limit was derived based on the IAEA methodology. The evaluation of the derived disposal concentration limit revealed that it is not suitable as a practical limit for intermediate level radioactive waste. This is because the disposal concentration limit according to the IAEA methodology is derived using a single value of radioactive waste density and the disposal facility's volume. The IAEA methodology is suitable for setting the concentration limit for vault type disposal, which consists of a single type of waste, whereas an underground silo type disposal facility is composed of several types of radioactive waste, and thus the IAEA methodology has limitations in determining the disposal concentration limit. It is necessary to develop and apply an improved method to derive the disposal concentration limit for intermediate level radioactive waste by considering the radioactivity of various types of radioactive waste, the corresponding scenario evaluation results, and the regulatory limit.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.15 no.3
• /
• pp.265-279
• /
• 2017

The Gyeongju underground silo type disposal facility, approved for use in December 2014, is in operation for the disposal of low and very low-level radioactive wastes, excluding intermediate-level waste. That is why the existing low-level radioactive waste level has been subdivided and the concentration limit value for intermediate-level waste has been changed in accordance with Nuclear Safety Commission Notice 2014-003. For the safe disposal of intermediate-level wastes, new optimization methodology for calculating the concentration limit of intermediate radioactive level wastes at an underground silo type disposal facility was developed. According to the developed optimization methodology, concentration limits of intermediate-level wastes were derived and the inventory of radioactive nuclides was evaluated. The operation and post closure scenarios were evaluated for the derived radioactive nuclide inventory and the results of all scenarios were confirmed to meet the regulatory limit. However, in case of $^{14}C$, it was confirmed that additional radioactivity limitation through a well scenario was needed in addition to the limit of disposal concentration. It was confirmed that the derived intermediate concentration limit of radioactive waste can be used as the intermediate-level waste concentration limit for the underground disposal facility. For the safe disposal of intermediate-level wastes, KORAD plans to acquire additional data from the radioactive waste generator and manage the cumulative radioactivity of $^{14}C$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1994.04a
• /
• pp.260-265
• /
• 1994

High strength concrete(65MPa) was used for construction of the bulk cement storage silo by using sliding form. This paper presents mix design, production, quality control and experience with field application of high strength concrete under cold weather conditions. It is shown to be possible to produce high strength concrete of compressive strength of 50~60 MPa by using high-range water reducer to lower w/c ratio with appropriate quality control.

• Asian-Australasian Journal of Animal Sciences
• /
• v.3 no.4
• /
• pp.323-330
• /
• 1990

Two experiments were conducted to evaluate the effect of processing and method of ensiling on the digestion and utilization of high moisture barley (HMB) in cattle. In experiment 1, four Holstein heifers were assigned in a Latin square design to diets containing 70% barley, 25% alfalfa hay and 5% supplement on a dry matter (DM) basis. Diets differed only in the type of barley fed: rolled dry barley (R-DB), rolled HBM (R-HMB), ground HMB (G-HMB) or unprocessed HMB (U-HMB). In experiment 2, three Holstein steers were fed 85.2% barley, 10.2% whole plant barley silage and 4.6% supplement on a DM basis. Again, diets differed only in the type of barley fed: R-DB, rolled HMB from a pit silo (Pit-HMB) or rolled HMB from a Harvestore silo (HAV-HMB). In experiment 1, digestibility coefficients for animals fed R-HMB were significantly higher than observed for U-HMB. While not significant, a similar trend for decreased digestibility was observed for R-DB and G-HMB. Animals fed HMB had significantly lower ruminal propionate concentrations. In addition, the rate of degradation of the degradable DM and crude protein (CP) fractions was slower for HMB than for dry barley. In experiment 2, a trend to lower digestibility coefficients was observed for animal fed R-DB compared to those fed Pit-HMB or HAV-HMB. Ruminal propionate concentrations for animals fed R-DB also tended to be higher than for those fed the HMB diets. Dry matter and CP disappearances from nylon bags was substantially lower for Pit-HMB than for R-DB or HAV-HMB. The results suggest that replacement of dry barley by rolled or unprocessed HMB in the diet of animals fed high grain diets may contribute to a more stable rumen environment.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.7
• /
• pp.1103-1112
• /
• 2020

Objective: To measure whether a microbial additive could effectively improve the fermentation quality of delayed-sealing (DS) silage, we studied the effects of inoculants of lactic acid bacteria (LAB) and cellulase enzyme on microbial populations, ensiling characteristics, and spoilage loss of DS silage of Napier grass in Africa. Methods: Quick-sealing (QS) and DS silages were prepared with and without LAB (Lactobacillus plantarum) inoculant, cellulase enzymes, and their combination. The QS material was directly chopped and packed into a bunker silo. The DS material was packed into the silo with a delay of 24 h from harvest. Results: In the QS silage, LAB was dominant in the microbial population and produced large amounts of lactic acid. When the silage was treated with LAB and cellulase, the fermentation quality was improved. In the DS silage, aerobic bacteria and yeasts were the dominant microbes and all the silages were of poor quality. The yeast and mold counts in the DS silage were high, and they increased rapidly during aerobic exposure. As a result, the DS silages spoiled faster than the QS silages upon aerobic exposure. Conclusion: DS results in poor silage fermentation and aerobic deterioration. The microbial additive improved QS silage fermentation but was not effective for DS silage.

• Asian-Australasian Journal of Animal Sciences
• /
• v.13 no.11
• /
• pp.1542-1547
• /
• 2000

To standardize proper formulation of urea and molasses, the former to increase crude protein content of tropical grass and the latter for improving its silage quality, we examined the fermentation quality of silage of fresh and wilted napiergrass (Pennisetum purpureum Schumach) with different levels of urea and molasses with or without lactic acid bacteria (LAB). Silage was made of napiergrass with conditions of fresh young (Exp. 1),young wilted for half day (Exp. 2) and fresh mature (Exp. 3). Chopped plant materials of about 1cm length were ensiled into a laboratory silo and incubated for one month at $25^{\circ}C$. The treatments were the combination of 0, 0.2 and 0.6% of urea and 0, 2 and 5% of molasses (fresh material basis) with or without LAB inoculation. After opening the silo, pH, organic acids, volatile basic nitrogen (VBN) and total nitrogen (TN) were determined. Addition of molasses significantly (p<0.01) lowered pH values in three experiments. Though molasses addition increased lactic acid production even at a higher level of urea, pH values at 0 and 2% molasses were significantly increased by urea in fresh and wilted young silages, but in fresh mature silage it occurred only when molasses was not added. VBN/TN at 0.6% urea were decreased significantly by the highest molasses in three experiments. Significant increases in TN by the increasing of urea addition were observed at all levels of molasses in wilted young and fresh mature silages. In conclusion, a combination of 5% molasses and 0.6% urea could improve the nutritive and fermentation qualities of napiergrass silage under young, wilting and mature conditions.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.11
• /
• pp.1564-1567
• /
• 2001

Hydrolysis of plant protein to non-protein nitrogen (N) or ammonia can reduce quality of silage crops. Heating or non-enzymatic browning is a treatment to inhibit this hydrolysis. This experiment was conducted to examine the effects of pre-heated soybean meal and molasses on the fermentation quality of napiergrass silage. The initial growth of napiergrass was harvested at 85 days of age and immediately chopped into about 1 cm length. About 700 g of the grass was ensiled into a laboratory silo (1.0 liter polyethylene container) and incubated for 30 days at room temperature ($28^{\circ}C$). No additives (control), molasses, soybean meal and molasses + soybean meal treatments were prepared. All additives were non-heated or heated in an oven at $150^{\circ}C$ for 30 minutes before ensiling. Molasses was added at 3% on the fresh weight basis and soybean meal was added at 0.5% N, respectively. After opening the silo, pH, total nitrogen (TN), volatile basic nitrogen (VBN), lactic acid (LA), acetic acid (AA), butyric acid (BA) and dry matter (DM) contents were determined. The data were analyzed statistically by analysis of variance. Compared with control, molasses addition significantly decreased pH value, VBN/TN, AA and BA and increased LA production. Soybean meal addition significantly increased TN and VBN/TN of silage. Both molasses and soybean meal addition significantly reduced pH value, AA, and BA and increased DM and LA contents of silage. The heating of additives was only effective to reduce VBN/TN production compared with non-heated additives in soybean meal and soybean meal with molasses addition.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.9
• /
• pp.1304-1312
• /
• 2013

The effects of storage period and aerobic deterioration on the bacterial community were examined in Italian ryegrass (IR), guinea grass (GG), and whole-crop maize (WM) silages. Direct-cut forages were stored in a laboratory silo for 3, 7, 14, 28, 56, and 120 d without any additives; live counts, content of fermentation products, and characteristics of the bacterial community were determined. 2,3-Butanediol, acetic acid, and lactic acid were the dominant fermentation products in the IR, GG, and WM silages, respectively. The acetic acid content increased as a result of prolonged ensiling, regardless of the type of silage crop, and the changes were distinctively visible from the beginning of GG ensiling. Pantoea agglomerans, Rahnella aquatilis, and Enterobacter sp. were the major bacteria in the IR silage, indicating that alcoholic fermentation may be due to the activity of enterobacteria. Staphylococcus sciuri and Bacillus pumilus were detected when IR silage was spoiled, whereas between aerobically stable and unstable silages, no differences were seen in the bacterial community at silo opening. Lactococcus lactis was a representative bacterium, although acetic acid was the major fermentation product in the GG silage. Lactobacillus plantarum, Lactobacillus brevis, and Morganella morganii were suggested to be associated with the increase in acetic acid due to prolonged storage. Enterobacter cloacae appeared when the GG silage was spoiled. In the WM silage, no distinctive changes due to prolonged ensiling were seen in the bacterial community. Throughout the ensiling, Weissella paramesenteroides, Weissella confusa, and Klebsiella pneumoniae were present in addition to L. plantarum, L. brevis, and L. lactis. Upon deterioration, Acetobacter pasteurianus, Klebsiella variicola, Enterobacter hormaechei, and Bacillus gibsonii were detected. These results demonstrate the diverse bacterial community that evolves during ensiling and aerobic spoilage of IR, GG, and WM silages.

• Steel and Composite Structures
• /
• v.12 no.4
• /
• pp.291-302
• /
• 2012

Frequently, steel silos are supported by discrete supports or columns to permit easy access beneath the barrel. In such cases, large loads are transferred to the limited number of supports, causing locally high axial compressive stress concentrations in the shell wall above the supports. If not dealt with properly, these increased stresses will lead to premature failure of the silo due to local instability in the regions above the supports. Local stiffening near the supports is a way to improve the buckling resistance, as material is added in the region of elevated stresses, levelling these out to values found in uniformly supported silos. The aim of a study on the properties of local stiffening will then be to increase the failure load, governed by an interaction of plastic collapse and elastic instability, to that of a discrete supported silo. However, during the course of such a study it was found that, although the failure remains local, the cylinder height is also a parameter that influences the failure mechanism, a fact that is not properly taken into account in current design practice and codes. This paper describes the mechanism behind the effect of the cylinder height on the failure load, which is related to pre-buckling deformations of the shell structure. All results and conclusions are based on geometrically and materially non-linear finite element analyses.

• Animal Bioscience
• /
• v.34 no.11
• /
• pp.1776-1783
• /
• 2021

Objective: This project aimed to evaluate the effects of both different additives and filling methods on nutritive quality, fermentation profile, and in situ digestibility of whole plant corn silage. Methods: Whole plant corn forage harvested at 26.72% dry matter (DM) was chopped and treated with two filling methods, i) fill silos at one time (F1), ii) fill silos at three times (F3), packing samples into one/three silo capacity at the first day, another one/three capacity at the second day, then one/three at the third day, three replicates. For each replicate, samples were treated with three additives, i) control (CTRL, no additive), ii) Sila-Max (MAX, Ralco Nutrition Inc., Marshall, MN, USA), and iii) Sila-Mix (MIX, Ralco Nutrition Inc., USA). With three replicates of each secondary treatment, there were nine silos, 54 silos in total. Each silo had a packing density of 137.61 kg of DM/m3. All silos were weighed and stored in lab at ambient temperature. Results: After 60 d of ensiling, all items showed good silage fermentation under MAX filled one time or three times (p<0.01). Higher silage quality for all additives was obtained at filling one time than that filled three times (p<0.01). The highest DM and lowest DM loss rate (DMLR) occurred to MAX treatment at two filling methods (p<0.01); Digestibility of acid detergent fiber, neutral detergent fiber (NDF), and curde protein had the same results as silage quality (p<0.01). Yield of digestible DM and digestible NDF also showed higher value under MAX especially for filling one time (p<0.05). Conclusion: All corn silages showed good fermentation attributes (pH<4.0). The forage filled one time had higher silage quality than that filled three times (p<0.01). MAX with homofermentative lactic acid bacteria enhanced the lactic acid fermentation, silage quality and nutrient digestibility, and so improved the digestible nutrient yield.