• Transactions on Electrical and Electronic Materials
• /
• v.11 no.5
• /
• pp.212-215
• /
• 2010

$BiFeO_3/Pb(Zr_{0.95}Ti_{0.05})O_3$ (BFO/PZT) heterolayered thin films were fabricated by the spin coating method on a Pt/Ti/$SiO_2$/Si substrate using metal alkoxide solutions. The coating and heating procedure was repeated 6 times to form the heterolayered films. The thickness of the BFO/PZT films after one cycle of drying/sintering is about 30-40 nm. All BFO/PZT films show a void free uniform grain structure without the presence of rosette structures. It can be assumed that the crystal growth of the upper BFO layers can be influenced by the lower PZT layers. As the number of coatings increased, the dielectric constant increased, so that the value for the 6-layer film was 1360 at 1 KHz.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.153-156
• /
• 2000

This paper presents an PID type fuzzy based method for nohnear engine idle controller The output is a duty cycle(DC) for driving a idle speed cont개l valve(1SCV). For precise control of SI engine, the CPS sensor and coolant temperature are used. Visual C* language is used to make simulation panel for the fast and precise idle speed control. The dSPACE board and supported Control desk program is used in experiment ta the same purpose as simulation. The experimental results have a good agreement with simulation ones.

• Progress in Superconductivity
• /
• v.5 no.2
• /
• pp.136-140
• /
• 2004

We fabricated and tested a resistive superconducting fault current limiters (SFCL) operated at 3.8 ㎸ based on YBCO thin films. The SFCL was composed of 7 components connected in series. Each component was designed to be capable of current limiting at 600 V, and has a SiC shunt resistor ( $R_{s}$) of 40 Ω in Parallel. Short circuit tests were carried out fur 0 and 90 degree faults lasting fur 5 cycles. The test results showed that the 7 components were quenched simultaneously under the safe quenches and evenly shared the applied voltage. The SFCL successfully suppressed the fault currents below 94 $A_{peak}$ within the quarter cycle after fault.t.t.

• Transactions of Materials Processing
• /
• v.15 no.3 s.84
• /
• pp.195-205
• /
• 2006

This paper focuses on a rheo-forming of am part fabricated by electromagnetic stirring system (EMS). This forming process take place under high pressure of high pressure die casting and thin walled casting is possible. Furthermore, the productivity is better than low pressure die casting because of shorter cycle time. The advantages of rheo-forming are performed in the semi solid state with laminar flow and the gas content is low, which makes welding possible. Therefore this research applies for arm part with EMS and has investigated the mechanical properties after T6 and T5 heat-treatment.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.103.2-103.2
• /
• 2011

리튬이차전지의 음극물질로서 상용화되고 있는 탄소재료중 흑연은 전기자동차에 적용하기에는 낮은 용량과 나쁜 출력특성을 갖고 있어 지금보다 두배이상의 용량과 출력특성이 좋은 음극소재의 개발이 필요하다. 또 다른 음극물질로 실리콘은 흑연에 비해 월등히 높은 이론용량을 나타내고 있지만 실리콘이 리튬이온과 만나면 부피가 4배이상 팽창하여 사이클이 진행될수록 충방전 용량이 급격히 감소하게 된다. 그래서 본 연구에서는 이 두 음극소재를 상호보완하기 위해 천연흑연을 산처리 과정을 통해 제조된 팽창흑연을 매트릭스로 사용하여 팽창흑연에 실리콘을 충진 시키는 연구를 진행하였다. 팽창흑연에 실리콘을 충진시킴으로써 1C일 때 약 650mAh/g의 용량을 나타내었으며, 50cycle이 진행된 후에도 비교적 안정한 사이클 특성을 나타내었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.70-70
• /
• 2011

차세대 저항 메모리로 활용 가능한 ZnO 박막의 저항 변화 특성을 평가하였다. ZnO 박막은 Pt/Ti/SiO2/Si 기판 위에 스퍼터링 시스템을 이용하여 약 50nm 두께로 증착되었다. 증착된 박막에 전극을 evaporator를 이용하여 패턴닝 함으로써 전극-반도체-전극 구조의 소자를 만들고 전기적 특성을 평가하였다. 비교적 높은 compliance current (이하Icomp)를 설정한 경우 unipolar 저항 변화특성을 나타낸 데 비해 비교적 낮은 Icomp를 설정한 경우 bipolar 저항 변화특성을 나타내었다. 두 서로 다른 저항 변화 특성은 100cycle 이상 안정적으로 재현성 있게 나타났으며 이때의 저항비는 약 $10^3$ 정도를 나타냈다. 본 결과를 바탕으로 필라멘트 이론에 기초한 저항 변화 메커니즘을 설명하는 모델이 제시되었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.5
• /
• pp.709-717
• /
• 2000

Cyclic variability has long been recognized as limiting the range of operating conditions of spark ignition engines, in particular, under lean and highly diluted operation conditions. The cyclic combustion variations can be characterized by the pressure parameters, combustion parameters, and flame front parameters. The coefficient of variation in indicated mean effective pressure ($COV_{IMEP}$) defines the cyclic variability in indicated work per cycle, and it has been found that vehicle driveability problems usually result when $COV_{IMEP}$ exceeds about 10%. For analysis of the cyclic variability in SI engines at idling, the results show that cyclic variability by the $COV_{IMEP}$ or the coefficient of variation in maximum pressure can be explained and may be consequently reduced by the help of the optimum spark timings.

• Korean Journal of Materials Research
• /
• v.7 no.5
• /
• pp.381-385
• /
• 1997

PEMOCVD에 의해서 SrBi$_{2}$Ta$_{2}$O$_{9}$밥막이 낮은 온도에서 성공적으로 Pt/Ti/SiO$_{2}$Si위에 증착되었다. 5$50^{\circ}C$에서 증착된 200nm박막은 치밀하고 작은 결정립을 보였으며 3V의 인가전압하에서 이력곡선은 포화되기 시작하였다. 3V에서 박막은 잔류분극 (P$_{r}$)과 항전계(E$_{c}$)는 각각 15$\mu$/$\textrm{cm}^2$과 50kV/cm이었다. 6V bipolar square pulse의 피로측정에서 박막은 1.0x$10^{11}$cycles까지 피로 현상을 보이지 않았다. PEMOCVD에 의해서 5$50^{\circ}C$에서 증착된 SBT박막은 비휘발성 기억소자에 충분히 활용할 수 있다.다.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.45-50
• /
• 2022

The etching with high selectivity of silicon dioxide over silicon nitride is essential in semiconductor fabrication, and gas phase etch (GPE) can increase the competitiveness of the selective dielectric etch. In this work, GPE of plasma enhanced chemical vapor deposited SiO₂ was performed, and the effects of process parameters, such as temperature, partial pressure ratio, and gas supply cycle, are investigated in terms of etch rate and within wafer uniformity. Employing multiple regression analysis, the importance of each parameter elements is analyzed.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.3
• /
• pp.83-93
• /
• 1985

The prediction of emission concentrations in a 4cycle spark ignition engine was made by considering nonuniform model with thermodynamics, chemical equilibrium and kinetic mechanism of nitric oxide. Calculation of this model shows that a temperature difference of the order of 500K can be established across he cylinder. Results of the kinetic calculation of nitric oxide show that the temperature gradient across the cylinder has a profound effect on the nitric oxide formation. The predicted values for nitric oxide, carbon dioxide and carbon monoxide agree with measured ones for a variety of equivalence ratio.