Journal of Korean Society of Environmental Engineers
/
v.33
no.3
/
pp.196-201
/
2011
Emission from meat cooking may contribute to the concentration of the Particulate Matters(PM) in the city. This study is to investigate the particle size and the emission characteristics of particulate matters from pork and beef cooking. The chamber was installed for sampling of PM generated from pork belly and beef sirloin cooking including seasoned ones. Cascade Impactor and Portable Aerosol Monitor (PAM) were used to analyse the particle size distribution. At the result of the Cascade Impactor sampling, particulate matters from the pork cooking was higher than that of beef. The gravimetric concentration of PM according to the size was highest at the range of $1.95{\sim}3.2{\mu}m$ and the gravimetric concentration of PM from the non-seasoned meat was higher than that of the seasoned one. The emission factors from pork, pork seasoned, beef and beef seasoned were 1.36 g/kg, 1.03 g/kg, 1.23 g/kg, 0.92 g/kg respectively. To see the result of PAM sampling, the ranges of $1.6{\sim}2.5{\mu}m$ and $2.5{\sim}3.5{\mu}m$ were reveled as highest. The ration of $PM_{2.5}/PM_{10}$ from pork and beef was 0.56~0.58. The emission factors from pork, pork seasoned, beef and beef seasoned measured by PAM were revealed as 3.37 g/kg, 2.76 g/kg, 2.93 g/kg, 2.77 g/kg respectively.
Several isotopomers of cyclooctanone were prepared by selective deuterium substitution. Intrinsic isotope effects on $^{13}C$ NMR chemical shifts of these isotopomers were investigated systematically at low temperature. These istope effects were discussed in relation to the preferred boat-chair conformation of cyclooctanone. Deuterium isotope effects on NMR chemical shifts have been known for a long time. Especially in a conformationally mobile molecule, isotope perturbation could affect NMR signals through a combination of isotope effects on equilibria and intrinsic effects. The distinction between intrinsic and nonintrinsic effects is quite difficult at ambient temperature due to involvement of both equilibrium and intrinsic isotope effects. However if equilibria between possible conformers of cyclooctanone are slowed down enough on the NMR time scale by lowering temperature, it should be possible to measure intrinsic isotope shifts from the separated signals at low temperature. $^{13}C$ NMR has been successfully utilized in the study on molecular conformation in solution when one deals with stable conformers or molecules were rapid interconversion occurs at ambient temperature. The study of dynamic processes in general requires analysis of spectra at several temperature. Anet et al. did $^1H$ NMR study of cyclooctanone at low temperature to freeze out a stable conformation, but were not able initially to deduce which conformation was stable because of the complexity of alkyl region in the $^1H$ NMR spectrum. They also reported the $^1H$ and $^{13}C$ NMR spectra of the $C_9-C_{16}$ cycloalkanones with changing temperature from $-80^{\circ}C$ to $-170^{\circ}C$, but they did not report a variable temperature $^{13}C$ NMR study of cyclooctanone. For the analysis of the intrinsic isotope effect with relation to cylooctanone conformation, $^{13}C$ NMR spectra are obtained in the present work at low temperatures (up to $-150^{\circ}C$) in order to find the chemical shifts at the temperature at which the dynamic process can be "frozen-out" on the NMR time scale and cyclooctanone can be observed as a stable conformation. Both the ring inversion and pseudorotational processes must be "frozen-out" in order to see separate resonances for all eight carbons in cyclooctanone. In contrast to $^1H$ spectra, slowing down just the ring inversion process has no apparent effects on the $^{13}C$ spectra because exchange of environments within the pairs of methylene carbons can still occur by the pseudorotational process. Several isotopomers of cyclooctanone were prepared by selective deuterium substitution (fig. 1) : complete deuterium labeling at C-2 and C-8 positions gave cyclooctanone-2, 2, 8, $8-D_4$ : complete labeling at C-2 and C-7 positions afforded the 2, 2, 7, $7-D_4$ isotopomer : di-deuteration at C-3 gave the 3, $3-D_2$ isotopomer : mono-deuteration provided cyclooctanone-2-D, 4-D and 5-D isotopomers : and partial deuteration on the C-2 and C-8 position, with a chiral and difunctional case catalyst, gave the trans-2, $8-D_2$ isotopomer. These isotopomer were investigated systematically in relation with cyclooctanone conformation and intrinsic isotope effects on $^{13}C$ NMR chemical shifts at low temperature. The determination of the intrinsic effects could help in the analysis of the more complex effects at higher temperature. For quantitative analysis of intrinsic isotope effects, the $^{13}C$ NMR spectrum has been obtained for a mixture of the labeled and unlabeled compounds because the signal separations are very small.
Kim, Jae-Won;Sim, Jin-Seob;Jang, Yo-Jong;Kang, Dong-Yun;Choi, Gye-Suk
The Journal of Korean Society for Radiation Therapy
/
v.22
no.1
/
pp.47-51
/
2010
Purpose: In the treatment of high-energy protons Air gap (the distance between the patient and the exit Beam) Lateral Penumbra of the changes to the increase in the radiation fields can form unnecessary and Increase the maximum dose at the site of treatment and reduced the minimum dose homogeneity of dose distributions can decline. Air gap due to this change in dose distribution compared to investigate studied. Materials and Methods: Received proton therapy at our institution Lung, Liver patients were selected and the size of six other Air gap in Field A and Field B 2, 4, 6, 8, 10 cm Proton external beam planning system by setting up a treatment plan established. Air gap according to the Lateral Penumbra area and DVH (Dose Volume Histogram) to compare the maximum dose and minimum dose of PCTV areas were compared. In addition, the dose homogeneity within PCTV Homogeneity index to know the value and compared. Results: Air gap (2, 4, 6, 8, 10 cm) at each change in field size were analyzed according to the Lateral Penumbra region Field A Change in the Air gap 2~10 cm by 1.36~1.75 cm, the average continuously increased about 28.7% and Field B Change in the Air gap 2~10 cm by 1.36~1.75 cm, the average continuously increased about 31.6%. The result of DVH analysis for relative dose of the maximum dose According to Air gap 2~10 cm is the mean average of 110.3% from 108.1% to a sustained increased by approximately 2.03% and The average relative dose of minimum dose is the mean average of 93.9% percent to 90.8 percent from the continuous decrease of about 3.31 percent. The result of Homogeneity index value to the according to Air gap 2~10 cm is the 2-fold increase from 1.09 to 2.6. Conclusion: In proton therapy case, we can see the increasing of lateral penumbra area when airgap getting increase. And increasing of Dmax and decreasing Dmin in the field are making increase homogeneity index, So we can realize there are not so good homogeneity in the PCTV. Therefore we should try to minimize air gap in proton therapy case.
We increasingly see the importance of employees acquiring enough expert capability or innovation capability to prepare for ever growing uncertainties in their operation domains. However, despite the above circumstances, there have not been an enough number of researches on how operational input components for employees' innovation outcome, innovation activities such as acquisition, exercise and promotion effort of employee's innovation capability, and their resulting innovation outcome interact with each other. This trend is believed to have been resulted because most of the current researches on innovation focus on the units of country, industry and corporate entity levels but not on an individual corporation's innovation input components, innovation outcome and innovation activities themselves. Therefore, this study intends to avoid the currently prevalent study frames and views on innovation and focus more on the strategic policies required for the enhancement of an organization's innovation capabilities by quantitatively analyzing employees' innovation outcomes and their most suggested relevant innovation activities. The research model that this study deploys offers both linear and structural model on the trio of learning, innovation capability and innovation outcome, and then suggests the 4 relevant hypotheses which are quantitatively tested and analyzed as follows: Hypothesis 1] The different levels of innovation capability produce different innovation outcomes (accepted, p-value = 0.000<0.05). Hypothesis 2] The different amounts of learning time produce different innovation capabilities (rejected, p-value = 0.199, 0.220>0.05). Hypothesis 3] The different amounts of learning time produce different innovation outcomes. (accepted, p-value = 0.000<0.05). Hypothesis 4] the innovation capability acts as a significant parameter in the relationship of the amount of learning time and innovation outcome (structural modeling test). This structural model after the t-tests on Hypotheses 1 through 4 proves that irregular on-the-job training and e-learning directly affects the learning time factor while job experience level, employment period and capability level measurement also directly impacts on the innovation capability factor. Also this hypothesis gets further supported by the fact that the patent time absolutely and directly affects the innovation capability factor rather than the learning time factor. Through the 4 hypotheses, this study proposes as measures to maximize an organization's innovation outcome. firstly, frequent irregular on-the-job training that is based on an e-learning system, secondly, efficient innovation management of employment period, job skill levels, etc through active sponsorship and energization community of practice (CoP) as a form of irregular learning, and thirdly a model of Yί=f(e, i, s, t, w)+${\varepsilon}$ as an innovation outcome function that is soundly based on a smart system of capability level measurement. The innovation outcome function is what this study considers the most appropriate and important reference model.
Journal of the Korean Society of Earth Science Education
/
v.12
no.3
/
pp.208-223
/
2019
In this study, it was analyzed first the views of nature of elementary and middle school students using the analysis framework of the views of nature that reflects the results of the literature analysis on the traditional views of nature that Koreans traditionally have. Next, it was analyzed characteristics of the views of nature which elementary and secondary school teachers. Finally, it was discussed the implications of the results of analysis of students' and teachers' views on science education in elementary and secondary schools. For this purpose, the framework for analysis the views of nature was reconstructed by combining the characteristics of Korean's traditional views of nature (Lee & Son, 2017) with the framework developed by Cobern and his colleagues (Cobern, Gibson, & Underwood, 1995). And in order to analyze in depth how students and teachers perceive nature, each question was asked to write a reason why they thought about their responses. According to the study, students and teachers respected nature and viewed it as a living creature, and had the view that nature was cyclical and that humans and nature interacted with each other. And they also had a traditional Korean view of nature that they consider naturalness important and nature is beautiful. It can be said that this is different from the view of Western modern science which perceives the world as a material and see nature with the view of linear time. Therefore, Korea's traditional views of natures, which students and teachers have, can be a conflict with the view of modern science in science class. Therefore, the science teaching strategy for students and teachers with different natural views will require consideration of the individual's understanding of nature and lesson strategies related to it. And it is also necessary that science textbook and science class cultures need to actively interact with teachers and students, and between students to share and understand each other's view of nature, and create a science class culture that considers the values students have and views on nature.
The purpose of this study was to examine the consumers' acceptance of irradiated foods according to sociodemographic characteristics and the factors to distinguish subjects with differential levels of their willingness to buy them. Data were collected from the 365 women living in Youngnam area by the self-administered questionnaire. The results from this study were as follows. First, consumers were concerned regarding food safety issues in general and particularly preservatives. Second, many subjects had not heard of the irradiated foods and showed wait-and-see attitude in the willingness to accept them. Consumers' willingness to purchase them were higher than any other cases if radiation would not remain in foods. Third, the results from the discriminant analyses showed that the concern toward food safety, perceived innovativeness, willingness to pay more for organic foods, and knowledge of irradiation were the factors to distinguish groups with differential levels of willingness to purchase the irradiated foods. The results from the study imply that accurate and scientific information about food irradiation should be given to the consumers.
Journal of Korean Tunnelling and Underground Space Association
/
v.20
no.3
/
pp.543-560
/
2018
With the increased development in downtown underground space facilities that vertically cross under a railway at a shallow depth, the demand for non-open cut method is increasing. However, most construction sites still adopt the pipe roof method, where medium and large diameter steel pipes are pressed in to form a roof, enabling excavation of the inside space. Among the many factors that influence the loosening region and loads that occur while pressing in steel pipes, the size of the pipe has the largest impact, and this factor may correspond to the magnitude of load applied to the underground structure inside the steel pipe roof. The super equilibrium method (SEM) has been developed to minimize ground disturbance and loosening load, and uses small diameter pipes of approximately 114 mm instead of conventional medium and large diameter pipes. This small diameter steel pipe is called an SEM pile. After SEM piles are pressed in and the grouting reinforcement is constructed, a crossing structure is pressed in by using a hydraulic jack without ground subsidence or heaving. The SEM pile, which plays the role of timbering, is a fore-poling pile of approximately 5 m length that prevents ground collapse and supports surface load during excavation of toe part. The loosening region should be adequately calculated to estimate the spacing and construction length of the piles and stiffness of members. In this paper, we conducted a comparative analysis of calculations of loosening load that occurs during the press-in of SEM pile to obtain an optimal design of SEM. We analyzed the influence of factors in main theoretical and empirical formulas applied for calculating loosening regions, and carried out FEM analysis to see an appropriate loosening load to the SEM pile. In order to estimate the soil loosening caused by actual SEM-pile indentation and excavation, a steel pipe indentation reduction model test was conducted. Soil subsidence and soil loosening were investigated quantitatively according to soil/steel pipe (H/D).
A survey was conducted to study attitudes of physician, nurse and patient towards physician's and nurse's uniform, from March 1 to March 31, 1996. The study population was 130 physicians and 147 nurses engaged in Yeungnam University Medical Center and 211 inpatients of Yeungnam University Medical Center. A questionnaire method was used to collect data. The following are summaries of findings: In the respect of physician's uniform, both physicians and nurses preferred other type of gown to the traditional coat-typed one and especially, nurses preferred more than physicians. Patients showed no difference in the preference of the traditional one and other form of gown as a whole but those who had higher educational level preferred other form of gown(p<0.01). Regarding the color of physician's gown, 73.6% of physicians and nurses liked white color, and 86.3% of the patients also liked the white color. Male physicians preferred the white color more than female physicians and nurses(p<0.01). Patients showed no meaningful difference for the color. The opinion of insisting on wearing a necktie when physician see patients was given by male physicians, physicians of fifty or more, physicians working in the field of medicine and professors, which showed significantly higher percentage than other groups(p<0.01). In the group of patiens, the same opinion was given by female, the group of sixty or more, the group of elementary school graduates or less and people residing in other cities and counties more than male, the group of other ages, the group of having higher educational level and people of Taegu city(p<0.01). It tended to agree wearing casual wear of physician during the working time of weekend and holiday as a whole. Younger physicians showed significantly higher preference for it(p<0.05). Regarding the nurse's uniform, both physicians and nurses preferred trousers, and 96% of the nurses did. Especially, nurses who were forty years old or more and who served at outpatient department and administrative and aid parts expressed 100 percent partiality to trousers. For the patients, those who had lower educational level preferred skirt and those who had higher educational level preferred trousers. As to the color of nurse's gown, 46.7% of the physicians and nurses liked white color. The physicians preferred white and nurses preferred other color(p<0.01). Of the patients, 79.1% liked white color. Regarding the wearing cap, 95.9% of the nurses replied it didn't have to wear the cap. The nurses who were fifty or more and who served at outpatient department and special parts gave whole answers of not having to wear the cap. On the other hand, 77.7% of the patients answered nurse had to wear the cap. From the above findings, it would be advisable to give a change to the forms and colors of the gowns to match with the trend and sense of the time instead of insisting on the traditional typical ones.
The cartoon industry in Korea has continued to decline due to the contraction of published comics market and decrease in the number of comic books rental stores until the 2000s when it rapidly started to experience qualitative changes and quantitative growth due to the emergence of webtoon. The market size of webtoon industry, valued at 420 billion won in 2015, is expected to grow to 880.5 billion won by 2018. Notably, most cartoonists who draw cartoon strips are using digital devices and producing scripts in data, thereby overcoming the geographical, spatial and physical limitation of contents. As a result, a favorable environment for the creation of local ecosystems is generated. While the infrastructures of human resources are steadily growing by region, cartoon industries that are supported by the government policy have shown good performance combined with factors of creative infrastructures in local areas such as webtoon experience centers, webtoon campuses and webtoon creation centers, etc. Nevertheless, it is true that cartoon infrastructures are substantially based on a capital area which leads to an imbalanced structure of cartoon industry. To see the statistics, companies of offline cartoon business in Seoul and Gyeonggi Province make up 87%, except for distribution industry. In addition, companies of online cartoon business which are situated outside of Seoul and Gyeonggi Province form merely 7.5%. Studies and research on local webtoon are inadequate. The existing studies on local webtoon usually focus on its industrial and economic values, mentioning the word "local" only sometimes. Therefore, this study looked into the current status of local webtoon of the present time for the current state of local cartoon ecosystem, middle and long-term support from the government, and an alternative in the future. Main challenges include the expansion of opportunities to enjoy cartoon cultures, the independence of cartoon infrastructure, and the settlement of regionally specialized cartoon cultures. It means that, in order to enable the cartoon ecosystem to settle down in local areas, it is vital to utilize and link basic infrastructures. Furthermore, it is necessary to consider independence and autonomy beyond the limited support by the government. Finally, webtoon should be designated as a culture, which can be a new direction of the development of local webtoon. Furthermore, desirable models should be continuously researched and studied, which are suitable for each region and connect them with regional tourism, culture and art industry. It will allow the webtoon industry to soft land in the industry. Local webtoon, which is a growth engine of regions and main contents of the fourth industrial revolution, is expected to be a momentum for the decentralization of power and reindustrialization of regions.
Journal of the Korean Society for Marine Environment & Energy
/
v.18
no.4
/
pp.304-309
/
2015
To evaluate the degree of contamination caused by oil spill accident in the sea, the in-situ sensors which are based on the scientific method are needed in the real site. The sensors which are based on the fluorescence detection theory can provide the useful data, such as the concentration of oil. However these kinds of sensors commonly are composed of the ultraviolet (UV) light source such as UV mercury lamp, the multiple excitation/emission filters and the optical sensor which is mainly photomultiplier tube (PMT) type. Therefore, the size of the total sensing platform is large not suitable to be handled in the oil spill field and also the total price of it is extremely expensive. To overcome these drawbacks, we designed the fluorimeter for the oil spill detection which has compact size and cost effectiveness. Before the detail design process, we conducted the experiments to measure the excitation and emission spectrum of oils using five different kinds of crude oils and three different kinds of processed oils. And the fluorescence spectrometer were used to analyze the excitation and emission spectrum of oil samples. We have compared the spectrum results and drawn the each common spectrum regions of excitation and emission. In the experiments, we can see that the average gap between maximum excitation and emission peak wavelengths is near 50 nm for the every case. In the experiment which were fixed by the excitation wavelength of 365 nm and 405 nm, we can find out that the intensity of emission was weaker than that of 280 nm and 325 nm. So, if the light sources having the wavelength of 365 nm or 405 nm are used in the design process of fluorimeter, the optical sensor needs to have the sensitivity which can cover the weak light intensity. Through the results which were derived by the experiment, we can define the important factors which can be useful to select the effective wavelengths of light source, photo detector and filters.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.