• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.211-214
• /
• 2004

이륙과 음속 통과시 랜덤진동형태의 음향/진동환경에 노출되는 위성체의 음향/진동시험은 시제품을 완성한 후에 슨1행되므로 않은 시행착오를 겪거나, 과다한 안전계수를 사용하여 불필요한 무게증가 등의 문제점을 가지고 있다. 이러한 문제점을 극복하기 위하여 통계적 에너지 해석법 (Statistical Energy Analysis)을 이용한 선행 해석이 필요하다. 본 연구에서는 KOMPSAT-1 (Korea Multi-Purpose Satellite-1) 위성체의 SDM (Structural Dynamic Model)에 대하여 SEA 해석을 수행하였다. 감쇠 손실 인자 (Damping Loss Ffactor)는 단판을 분리하여, 연성 손실 인자(Coupling Loss Factor)는 SDM모델 하부의 두 샌드위치 패널을 분리하여 실험적으로 산정하였다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.11 no.5
• /
• pp.123-130
• /
• 2001

The purpose of this paper is to reduce the level of idling vibration on a steering wheel. In some cases, vibration on steering wheel is amplified due to the resonance between the first natural frequency of T-beam and engine idling speed. Using SDM(structural dynamic modification) technique, T-beam is redesigned to reduce its vibration. This paper used FRF(frequency response function) synthesis technique which is entirely dependent on experiment. But this method requires lots of test efforts to enhance its reliability of design. While combining this method with an analytic method. the experimental burden, the major drawback of FRP synthesis method, can be considerably relieved. Using ana1ytic sensitivity analysis, some effective modification regions are preliminarily chosen as candidate Positions where SDM can be applied to modify T-beam\`s dynamic characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.233-238
• /
• 2000

CNC machine tool is assembled by central processor, PLC(Programmable Logic Controller), and actuator. The sequential control of machine generally controlled by a PLC. The main fault occured at PLC in 3 control parts. In LC faults, operational fault is charged over 70%. This paper describes diagnosis model and data processing for remote monitoring and diagnosis system in machine tools with open architecture controller. Two diagnostic models based on the ladder diagram. Logical Diagnosis Model(LDM), Sequential Diagnosis Model(SDM), are proposed. Data processing structure is proposed ST(Structured Text) based on IEC1131-3. The faults from CNC are received message form open architecture controller and faults from PLC are gathered by sequential data.. To do this, CNC and PLC's logical and sequential data is constructed database.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.3
• /
• pp.1-8
• /
• 1998

In this paper, we propose a Neural Call Admission Control (CAC) method using a Sparse Distributed Memory(SDM). CAC is a key technology of TM network traffic control. It should be adaptable to the rapid and various changes of the ATM network environment. conventional approach to the ATM CAC requires network analysis in all cases. So, the optimal implementation is said to be very difficult. Therefore, neural approach have recently been employed. However, it does not mett the adaptability requirements. because it requires additional learning data tables and learning phase during CAC operation. We have proposed a neural network CAC method based on SDM that is more actural than conventioal approach to apply it to CAC. We compared it with previous neural network CAC method. It provides CAC with good adaptability to manage changes. Experimenatal results show that it has rapid adaptability and stability without additional learning table or learning phase.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.2
• /
• pp.25-30
• /
• 2003

In the case of a vibration sensitive equipment, it require a vibration free environment to provide its proper function. Especially, lithography and inspection device, which have sub-nanometer class high accuracy and resolution, have come to necessity for producing more improved Giga Class semi conductor wafers. This high technology equipments require very strict environmental vibration criteria in proportion to the accuracy of the manufacturing. In this paper, the dynamic analysis and modal test were performed to evaluate the dynamic properties of the constructing clean room structure. Based on these results, a structural dynamic modification(SDM) were required to satisfiy the vibration allowable limit for pression machine. Therefore, in order to improve the dynamic stiffness of clean room structure, the VSD system which can control the force applied on structure, were adopted and its utility were proved from dynamic test results of the improved structure after a modification work.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.354-359
• /
• 2012

Improvement of structure-borne noises in the vehicle compartments has been one of the primary concerns in the development of vehicles. The booming is an annoying low frequency interior noise and vibration in vehicle. But it is difficult to reduce the structure-born booming noise in traditional method - trial and error within the shorten development schedule. So in present, the structure dynamic modification (SDM) method helpful to predict the effect of the local mass, stiffness, and damping is introduced. So in order to reduce the interior booming noise, the SDM was performed, and verified with modal test result. It was shown that the interior booming noise was reduced as predicted.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.10
• /
• pp.513-519
• /
• 2001

This paper proposed a random sigma-delta modulator(RSDM), which is constructed by a 1st order sigma-delta modulator(SDM) and a simple structured random binary generator(RBG). The 1st order SDM produces a switching pulse waveform which has the same low-frequency component as the reference input, while the RBG spreads the distribution of the number of sampling per switching cycle, and thus disperses the spectrum spikes in the output. The relationship between the harmonic spectra and the number of sampling per switching cycle is studied through computer simulations, and the frequency spectra of the RSDM are confirmed in an experimental setup.

• Imaging Science in Dentistry
• /
• v.43 no.1
• /
• pp.59-62
• /
• 2013

Non-Hodgkin's lymphoma (NHL) constitutes a group of malignancies those arises from cellular components of lymphoid or extranodal tissues. The head and neck is the most common area for the presentation of these lymphoproliferative disorders. Primary involvement of salivary glands is uncommon. This report described a case of a 73-year-old female patient who presented with involvement of both nodal and extranodal sites, with predominant involvement of salivary glands. The tumor staging worked up along with imaging, histopathological, and immunohistochemical findings were discussed. Computed tomographic images showed the involvement of Waldeyer's ring, larynx, orbit, and spleen. This report described imaging and prognostic tumor markers in diagnosing, treatment planning, and prognosis.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.529-532
• /
• 2010

본 연구에서는 철근가격 급등과 배근시공도 작성 인력 부족에 대비하여 SDM# 제품군을 사용하여 이음/정착을 고려한 3차원 철근 배근 자동화 기술(RAP)로 철근 배근 자동생성 및 배근시공도 작성 시스템을 개발하였다. 최근 철근가격 급등으로 인한 공사원가상승/인건비 상승/배근시공도 작성 인력 부족 등의 기존현황의 문제점 등을 SDM# 제품군의 철근 배근 자동화 기술(RAP)을 이용하여 자동 철근배근/배근시공도 작성/정밀 골조물량 산출/인력절감/시공 정밀도 향상/골조 공사비 절감 등의 효과와 기존의 현장가공으로 인한 철근 손실률 8%를 공장가공을 적용함으로써 3% 수준으로 낮출 수 있어 5% 내외의 절감효과를 얻을 수 있다. 철근현장가공에서 공장가공 전환으로 골조물량 절감을 기대할 수 있고, 이음/정착/응력분포가 고려된 3차원 철근 배근 자동화 기술(RAP)을 이용하여 자동배근 알고리즘에 의한 배근시공도/가공도 작성 효율을 높이고, 기술 자립을 통해 건설시공 분야의 기술력 향상을 기대할 수 있다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.830-833
• /
• 2005

SDM(Structural Dynamics Modification) is to improve dynamic characteristics of a structure, more specifically of a base structure, by adding or deleting auxiliary(modifying) structures. In this paper, I will focus on the optimal layout of the stiffeners which are attached to the plate to maximize 1st natural frequency. Recently, a new topology method was proposed by yamazaki. He uses growing and branching tree model. I modified the growing and branching tree model. The method is designated modified tree model. To expand the layout of stiffeners, I will consider non-matching problem. The problem is solved by using local lagrange multiplier without the mesh regeneration. Moreover The CMS(Component mode synthesis) method is employed to reduce the computing time of eigen reanalysis using reduced componet models.