• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.759-762
• /
• 2003

The epitaxially grown Mg-doped GaN thin film was prepared by MOCVD (Metal Organic Chemical Vapor Deposition) for a SAW(Surface Acoustic Wave) filter. Mg-doped GaN thin film had enough properties for a SAW filter which include crystallinity and morphology. The surface morphology and crystalline of the Mg-doped GaN thin films were characterized using AFM and an X-ray rocking curve. The SAW filter, which was fabricated by lift-off process and frequency response, was measured by HP 8753C network analyzer. Center frequency was 96.687 MHz and SAW velocity was 5801 m/s when wavelength(λ) was 60${\mu}{\textrm}{m}$. Insertion loss was over -10 dB, Q was factor over 200, and side lobe attenuation was over 22 dB which was suitable for use as a SAW filter. Electro-mechanical coupling coefficient (k$^2$) was calculated from the measured data. k$^2$ was from 1 % to 1.44 %. The fabricated SAW filter using Mg-doped GaN/sapphire structure has good qualities as a filter and will be used as a SAW filter for operating RF frequency.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.31-34
• /
• 1998

CDMA base station SAW filter has been designed and fabricated successfully. Through the computer simulation, SAW filter is designed to have center frequency of 69.99MHz, ripples lower than 0.7dB and rejection level lower than 50dB. To obtain low noise band pass SAW filter, Input electrode has a apodization type and output electrode has a withdrawal type. For the fabrication of the SAW filter, Al thin film is deposited to the quartz substrates. The fabricated SAW filter has center frequency of 70.5MHz, ripples of 1dB and rejection level of 45dB.

• 한국정보통신학회논문지
• /
• 제3권2호
• /
• pp.291-304
• /
• 1999

주 연구에서는 압전체에서의 IDT 변환기, 음향 반사기에 대한 전기 음향 모드의 결합 모드 방정식을 유도, 정리함으로써 SAW 공진기 필터의 결합 모드를 수학적으로 분석할 수 있는 모델링 방법을 소프트웨어 설계 모듈화하고, SAW 공진기 필터를 구성하고 있는 각 구성 요소에 대한 회로적인 결합 방법의 제안을 통하여 SAW 결합 모드 공진기 필터의 설계 및 시뮬레이션 방법을 제안하였다. 또한, 제작된 소프트웨어 설계 모듈을 시뮬레이션 소프트웨어 패키지화함으로써 설계자가 손쉽게 이동통신기기용 결합 모드 공진기 필터를 설계할 수 있도록 그래픽 사용자 인터페이스를 갖는 SAW 결합 모드 공진기 필터의 설계 시뮬레이터를 구현하였으며 이를 통하여 이동통신기기에서 사용할 수 있는 결합 모드 공진기 필터를 모의 설계하고 주파수 특성을 해석함으로써 그 응용 타당성을 제시하였다.

• 한국음향학회지
• /
• 제18권1호
• /
• pp.16-24
• /
• 1999

사다리형 SAW 필터의 개발을 위해서 종래에는 설계변수 하나하나를 변화시켜 시행착오식으로 사양을 만족시키는 값을 찾아야만 하였다. 본 연구에서는 주어진 사양을 만족시킬 수 있는 사다리형 SAW 필터의 패턴을 자동으로 설계하는 최적 설계법을 개발하였다. 우선 Smith 등가회로 해석법을 이용하여 사다리형 SAW 필터용 해석 프로그램을 제작하였으며, 그 프로그램에 의한 시뮬레이션 결과를 실제 제작된 시작품의 성능과 비교해 봄으로써 타당성을 검증하였다. 이 해석 프로그램을 바탕으로 설계변수의 조정에 따른 성능변수의 변화 경향을 분석함으로써 최적 설계 알고리즘을 개발하였으며. 그 타당성 및 효용성을 기 상용화된 제품들에 대해 시험 설계해 봄으로써 증명하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.325-326
• /
• 2007

SAW filter was designed by optimization technique using impulse sampling. To carry out characteristics of SAW filter the uniform IDT was adapted. And SAW filter was fabricated on $LiNbO_3$ substrates to evaluate frequency response. To apply properties of photolithography, lift off method was used. Lift off method was superior to etch method in fabrication process, frequency response property was measured by network analyzer. From a measurement of acoustic property, SAW propagation velocity was 2663.5m/sec.

• 한국전기전자재료학회논문지
• /
• 제14권5호
• /
• pp.435-443
• /
• 2001

As power durable RF SAW filters, AL-(0∼2wt%)Cu alloy multi-layered thin electrodes were deposited on 42° LiTaO$_3$ piezoelectric substrates by magnetron sputtering process, and then ladder-type RF SAW filters, satisfying the electrical specification of CDMA transmission band, were fabricated through optimizing SAW resonator structures. The temperature of film electrodes in SAW filter was increased with RF power, and reached the maxima to cause a failure of SAW filters at the cut-off frequencies of the RF filter band. As RF power increases, the electrodes of Al-Cu alloy showed higher power durability than that of pure Al. The multi-layer laminated film of Al-1wt.% Cu/Cu/Al-1wt%Cu resulted in the best power durability up to 4W of RF power. Every film electrode, however, was destroyed within seconds whenever applying a critical RF power to SAW filters, regardless of the composition and structure of film electrodes. The breakdown of film electrodes under FR power seems to believe due to the fatigue of electrodes caused by repetitive cyclic stress of surface acoustic wave, which is amplified as RF power increases.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.5-8
• /
• 2000

This paper proposes GaN film as a piezoelectric material for SAW(surface acoustic wave) filters. The fabricated GaN SAW filter exhibited a very high velocity of 5800 ㎧and relatively low insertion loss of -9.9 dB without matching circuit. From Smith's equivalent circuit model, the calculated electromechanical coupling factor (K$^2$) was about 4.$\pm$03％. which is larger than those obtained from other thin film piezoelectric materials and allows the realization of wider filter fractional bandwidths.

• 전기의세계
• /
• 제31권2호
• /
• pp.141-146
• /
• 1982

In this paper, surface acoustic wave (SAW) bandpass filter is designed using the Fourier series approach and the I$_{0}$-shin window function. And also we studied a method to realize SAW filter using the apodized ID transducer which was fabricated with aluminum metallization of about 1500 A over .deg. thickness on Y-cut Z-propagating LiNbO$_{3}$, crystal by photolithographic technique (lift-off method). Experimental results on SAW bandpass filter responses show good agreements with the theoretical characteristics.s.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 추계종합학술대회 논문집
• /
• pp.173-176
• /
• 1999

Frequency responses of the surface acoustic wave(SAW) filters are simulated by using the impulse modeling. The simulation technique of the SAW filters is to use the Fourier transformation to make a correspondence between the impulse response of the filter and the taps in the delay line. Since the Fourier series must be truncated after a finite number of terms, window functions are often used to weight the coefficients to obtain the desirable side-lobe level and bandwidth. The filter design is operated through the iterative simulation procedures. The design process is capable of yielding filters with optimized frequency response characteristics.

• 한국결정성장학회지
• /
• 제4권2호
• /
• pp.134-138
• /
• 1994

표면탄성파 소자응요을 위하여 완전용융조성, 48.65 mole % $Li_2O에서 LiTaO_3(LT)$ 단결정(Y, X-axis)을 육성하였다. 육성된 $LiTaO_3(LT)$ 단결정의 SAW 소자성능을 확인하기 위하여 photolithography를 거쳐 기본적인 SAW filter를 제작하였다. Yamaju LT Y-cut 단결정 기판과 본 연구에서 제작된 RIST LT Y-cut 단결정 기판에서의 SAW특성결과를 비교하여 성능을 결정하였다. Yamaju LT 기판에서보다 본 연구에서 육성된 LT 단결정 기판에서 우수한 SAW 성능을 보였다.