• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.62-66
• /
• 2011

In this study, a new RF method to extract the drain-source voltage Vds-dependent gate-bulk capacitance of deep-submicron MOSFETs is developed by determining Vds-independent gate-source overlap capacitance using measured S-parameters. The accuracy of extraction method is verified by observing good agreements between the measured and modeled S-parameters. The lateral channel doping profile in the drain region is experimentally measured using a Vds-dependent curve of the overlap and depletion length obtained from the extracted data.

• Electrical & Electronic Materials
• /
• v.7 no.3
• /
• pp.225-230
• /
• 1994

In this paper, we have fabricated short channel MOSFETs with these parameters to verify the validity of process parameters extraction by DTC method. The experimental results of fabricated short channel devices according to the optimal process parameters demonstrate good device characteristics such as good drain current-voltage characteristics, low body effects and threshold voltage of$\leq$+-.1.0V, high punch through and breakdown voltage of$\leq$12V, low subthreshold swing(S.S) values of$\leq$105mV/decade.

• Analytical Science and Technology
• /
• v.26 no.4
• /
• pp.256-261
• /
• 2013

The efficiency of the two extractions (refluxing extraction and heating-block extraction) was compared to develop the simple analytical method for the determination of capsaicinoids, including capsaicin and dihydrocapsaicin in red pepper powder. For the method development, the parameters, including particle size, extraction time and sample size, were evaluated using ultra high performance liquid chromatography (u-HPLC). It was found that the most effective extraction time of the refluxing extraction was 3 hr. The higher extraction efficiency was obtained with the fine particle of a mild red pepper powder, while the particle size did not affect the extraction efficiency in case of the hot red pepper powder. The higher extraction efficiency was obtained with the small size of sample taken because of the ratio of the large extracting solvent to sample amount. The extraction efficiency of the refluxing method was 3-9% higher than that of the heating-block method, however, the heating-block method could be applied to the determination of capsaicinoids in the red pepper powder for the purpose of quality control of the product.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.66-73
• /
• 2010

This work was focused on the material parameter extraction for the isothermal cyclic deformation analysis for which Chaboche(Combined Nonlinear Isotropic and Kinematic Hardening) and Overlay(Multi Linear Hardening) models are normally used. In this study all the parameters were driven especially based on Overlay theories. A simple method is suggested to find out best material parameters for the cyclic deformation analysis prior to the isothermal LCF(Low Cycle Fatigue) analysis. The parameter extraction was done using 400 series stainless steel data which were published in the reference papers. For simple and quick review of the parameters extracted by suggested method, 1D FORTRAN program was developed, and this program could reduce the time for checking the material data tremendously. For the application to FE code ABAQUS user subroutine for the material models was developed by means of UMAT(User Material Subroutine), and the stabilized hysteresis loops obtained by the numerical analysis were in good harmony with test results.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.49-52
• /
• 2002

A new method is developed to extract model parameters of SiGe HBT equivalent circuit including the base impedance and base-collector junction capacitance. Using this method, all resistances and capacitances of SiGe HBT are independently determined from measured S-parameters using two-port parameter formula. This method is proposed to reduce possible errors generated from global optimization process, and its accuracy has been verified by finding good agreements between measured and modeled current / power gain up to 18 GHz.

• Proceedings of the IEEK Conference
• /
• 2000.07b
• /
• pp.957-960
• /
• 2000

A novel extraction method of high frequency small-signal model parameters for MOSFETS is proposed. From S-parameter measurement, this technique accurately extracts the model parameters including the charge conservation capacitance parameters. To consider charge conservation, nonreciprocal capacitance is considered. The modeled parameters fit the measurements very well without any optimization.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.11
• /
• pp.17-22
• /
• 2000

A novel and robust direct parameter extraction method for hybrid-p equivalent circuit model of HBT is proposed. A new expression that can accurately resolve the base internal resistance from the measured S-parameters is derived, and it is not sensitive to the values of parasitic access inductance values. Based on the expression, six analytical expressions for the other parameters is developed and these expressions for hybrid-p equivalent circuit modeling ensure robust, fast, and reliable parameter extraction.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4275-4280
• /
• 2011

Present study describes the optimization of disk type sorptive extraction using monolithic material (Mono Trap) for the analysis of volatile aroma compounds from Lantana camara L. in combination with gas chromatography/mass spectrometry (GC/MS). Monolithic material sorptive extraction (MMSE) is a new sampling technique using a monolithic hybrid adsorptive disk (O.D. 10 mm, 1 mm thickness) made of high purity silica and activated carbon having a large surface area chemically bonded with octadecyl silane (ODS). The experimental parameters that may influence the MMSE efficiency have been optimized. Linearity, accuracy, precision and detection limits were evaluated to assess the performance of the proposed method. The method was validated with real plant samples of Lantana camara L. Twenty eight compounds including the main representative compounds of ${\alpha}$-curcumene and ${\beta}$-caryophyllene were found in analyzed samples. Results proved that proposed method could be used as a good alternative for the analysis for such volatile aroma compounds in plant samples.

• Food Engineering Progress
• /
• v.14 no.4
• /
• pp.354-358
• /
• 2010

The methods for determining the diffusion parameters for the diffusion of d-limonene, a major volatile compound of orange juice, through a multi-layered food packaging material and predicting its absorption into the packaging material have been investigated. The packaging material used was the 1.5-mm thick multi-layered packaging material composed of high impact polystyrene (HIPS), polyvinylidene chloride (PVDC), and low density polyethylene (LDPE). Orange juice was placed in a cell where volatiles were absorbed in the sample package and kept at $23{\pm}2^{\circ}C$ for 72 hr. The d-limonene absorbed in a 1.5-mm thick multi-layered food packaging material was analyzed by a solid phase micro-extraction (SPME). The absorption parameters for the absorption of d-limonene in the packaging material were determined and absorption of d-limonene into the packaging material was predicted using absorption storage data. The SPME desorption at $60^{\circ}C$ for 1 hr resulted in the most sensitive and reproducible results. The diffusion coefficients of d-limonene in the packaging material and the partition coefficient at $23{\pm}2^{\circ}C$ were approximately $1-2{\times}10^{12}m^2$/s and 0.03, respectively. The absorption profile no earlier than 30 hr was fit well by a model derived from the Fick's law.

• Journal of Korean Society for Geospatial Information Science
• /
• v.8 no.2 s.16
• /
• pp.11-22
• /
• 2000

It needs to extract the accurate topological characteristics and hydrological parameters of watershed in order to manage water resource efficiently. But, these data are processed yet by manual wok and simple operation in hydrologic fields. In this paper, we presented algorithm that could extract topological characteristics and hydrological parameters over watershed using GSIS and it gives the saving of data processing tin and the confidency of data. We presented coupling method between GSIS and hydrologic model by using extracted parameters into the input parameter of HEC-HMS hydrologic model. The extraction procedure of topological characteristics and hydrological parameters is as below. First, watershed and stream are extracted by DEM and curve unmber is extracted throughout the overlay of landuse map and soil map. Also, we extracted surface parameters like the length of the longest flow path and the slope of the longest flow path by Grid computation into watershed and stream. And we gave the method that could extract hydrologic parameters like Muskingum K and sub-basin lag tin by executing computation into surface parameters and average Sn curve number being extracted.