• 한국정밀공학회지
• /
• 제25권2호
• /
• pp.148-155
• /
• 2008

The aim of the study is to interpret the distribution of occlusal force by 3-dimensional finite element analysis of ISP(Implant Supported Prosthesis) supported by minimum number of implant to restore the edentulous patients. For this study, the Astra Tech implant system is used. Geometric modeling for 6 and 4 fixture ISP group is performed with respect to the bone, implant and one piece superstructure, respectively. Implants are arbitrarily placed according to the anatomical limit of lower jaw and for the favorable distribution of occlusal force, which is applied at the end of cantilever extension of ISP with 30mm. Element type is tetrahedral for finite element model and the typical mechanical properties, Young's modulus and Poisson's ratio of each material, cortical, cancellous bone and implant material are utilized for the finite element analysis. From this study, we can see the distribution of equivalent stress equal to real situation and speculate the difference in the stress distribution in the whole model and at each implant fixture, From the analysis, the area of maximum stress is distributed on distal contact area between bone and fixture in the crestal bone. The maximum stress is 53MPa at the 0.2mm area from the bone-implant interface in the maximum side for 300N load condition for 4 fixture case, which is slightly less than the stress calculated from allowable strain. This stress has not been deduced to directly cause the loss of crestal bone around implant fixture, but the stress can be much reduced as the old peoples may have lower chewing force. Thus, clinical trial may be performed with this treatment protocol to use 4 fixtured ISP for old patients.

• 한국환경보건학회지
• /
• 제40권2호
• /
• pp.147-156
• /
• 2014

Objectives: This study was carried out to examine whether the apparent photolysis with or without sensitizers [NaOH and humic acid (HA)] was prompted photodegradation of polychlorinated biphenyl (PCB) in aqueous solution. Methods: PCBs photodegradation occurred using fluorescence black lamps at ${\lambda}_{max}=300nm$. PCB congeners were exposed in 10 ppm HA or 0.05N NaOH solutions, to investigate the decreasing profile of PCB concentration with time. The PCBs were then analyzed by gas chromatography/mass spectrometry (GC-MS). Reductive degradation profile of PCB congeners in the presence of both sensitizers under oxygen-saturated protic conditions was described using the wind-rose diagrams. Results: Use of HA or NaOH decreased PCB concentration with time in the dark and on irradiation, indicating that photolysis underwent through reductive dechlorination through energy transfer and possibly with reactive oxygens. The dechlorination was marked by a chromatographic shift, observed in the GC-MS plots. Therefore it is logical to assume that increasing the dose of sensitizers would increase the photodegradation rates of PCBs. The half-lives of pentachloro-PCB (penta-3) in 0.05N NaOH and 10 ppm HA were estimated at about 47 hours and 39 hours, respectively, under the same experimental conditions of photolysis. It was found that the rate of photolysis of pentachloro-PCB in aqueous solution followed apparent first-order kinetics compared to other congeners. Conclusion: Photochemical degradation (using 328 nm UV light) of penta- and hexa-PCBs in HA or alkaline solution is a viable method for pretreatment method. The results are helpful for the further comprehension of the reaction mechanism for photolytic dechlorination of PCBs in aquatic system.

• Parasites, Hosts and Diseases
• /
• 제50권2호
• /
• pp.119-126
• /
• 2012

Carboxylic acids play an important role in both aerobic and anaerobic metabolic pathways of both the snail and the parasite. Monitoring the effects of infection by schistosome on Biomphalaria alexandrina carboxylic acids metabolic profiles represents a promising additional source of information about the state of metabolic system. We separated and quantified pyruvic, fumaric, malic, oxalic, and acetic acids using ion-suppression reversed-phase high performance liquid chromatography (HPLC) to detect correlations between these acids in both hemolymph and digestive gland gonad complex (DGG's) samples in a total of 300 B. alexandrina snails (150 infected and 150 controls) at different stages of infection. The results showed that the majority of metabolite pairs did not show significant correlations. However, some high correlations were found between the studied acids within the control group but not in other groups. More striking was the existence of reversed correlations between the same acids at different stages of infection. Some possible explanations of the underlying mechanisms were discussed. Ultimately, however, further data are required for resolving the responsible regulatory events. These findings highlight the potential of metabolomics as a novel approach for fundamental investigations of host-pathogen interactions as well as disease surveillance and control.

• 한국작물학회지
• /
• 제49권1호
• /
• pp.52-60
• /
• 2004

The optimized in vitro culture system was investigated for improvement of regeneration efficiencies by observing the responses of scutella-derived callus of Korean rice (Oryza sativa L.). Large variations of callus induction (43.9-93.9%) and shoot regeneration (0-88.7%) were observed among the rice cultivars depending on medium. However, shoot regeneration was significantly improved by selected utilization of basal medium, growth regulators, and carbon sources. N6 basal medium was more efficient for embryogenic callus induction than MS or LS basal medium, while MS was superior to N6 for shoot regeneration. The calli of highly regenerative cultivars grew faster and showed higher rates of green tissue formation (GT) and shoot regeneration (SR) and lower rate of callus browning (CB) than those of recalcitrant cultivars. Although a higher level of kinetin stimulated the GT and SR in highly regenerative cultivars, $10\textrm{mgL}^{-1}$ kinetin generally suppressed the GT and SR, while CB was accelerated compared to $2\textrm{mgL}^{-1}$ kinetin. Additional benefits of sorbitol combined with maltose (or sucrose) under $5\textrm{mgL}^{-1}$ kinetin were certainly confirmed on regeneration efficiencies compared to sucrose alone as carbon source and osmotic regulator. This combination showed high rate of GT and SR with multiple shoots while low rate of CB. With MSRK5SM-Pr medium ($5\textrm{mgL}^{-1}$ kinetin, 3% sorbitol, 2% maltose, $500\textrm{mgL}^{-1}$ proline), the regeneration efficiencies of total 17 out of 24 cultivars were practically improved 160% on average compared to MSRK2S ($2\textrm{mgL}^{-1}$ kinetin, 3% sucrose) control medium. Especially, the medium was most effective to the cultivars showing a medium level of regenerability such as Daesanbyeo and Dongjinbyeo and Suwon477, enhancing efficiencies more than 300-600% compared to MSRK2S medium.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.65-65
• /
• 1999

Dry etching technique provides more easy controllability on the etch profile such as anisotropic etching than wet etching process and the results of lots of researches on the characterization of various plasmas or ion beams for semiconductor etching have been reported. Chlorine-based plasmas or chlorine ion beam have been often used to etch several semiconductor materials, in particular Si-based materials. We have studied the effect of He flow rate on the Si and SiO2 dry etching using chlorine-based plasma. Experiments were performed using reactive ion etching system. RF power was 300W. Cl2 gas flow rate was fixed at 58.6 sccm, and the He flow rate was varied from 0 to 120 sccm. Fig. 1 presents the etch depth of si layer versus the etching time at various He flow rate. In case of low He flow rate, the etch rate was measured to be negligible for both Si and SiO2. As the He flow increases over 30% of the total inlet gas flow, the plasma state becomes stable and the etch rate starts to increase. In high Ge flow rate (over 60%), the relation between the etch depth and the time was observed to be nearly linear. Fig. 2 presents the variation of the etch rate depending on the He flow rate. The etch rate increases linearly with He flow rate. The results of this preliminary study show that Cl2/He mixture plasma is good candidate for the controllable si dry etching.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.79-79
• /
• 1999

The varous techniques for fabrication of si or metal tip as a field emission electron source have been reported due to great potential capabilities of flat panel display application. In this report, 240nm thermal oxide was initially grown at the p-type (100) (5-25 ohm-cm) 4 inch Si wafer and 310nm Si3N4 thin layer was deposited using low pressure chemical vapor deposition technique(LPCVD). The 2 micron size dot array was photolithographically patterned. The KOH anisotropic etching of the silicon substrate was utilized to provide V-groove formation. After formation of the V-groove shape, dry oxidation at 100$0^{\circ}C$ for 600 minutes was followed. In this procedure, the orientation dependent oxide growth was performed to have a etch-mask for dry etching. The thicknesses of the grown oxides on the (111) surface and on the (100) etch stop surface were found to be ~330nm and ~90nm, respectively. The reactive ion etching by 100 watt, 9 mtorr, 40 sccm Cl2 feed gas using inductively coupled plasma (ICP) system was performed in order to etch ~90nm SiO layer on the bottom of the etch stop and to etch the Si layer on the bottom. The 300 watt RF power was connected to the substrate in order to supply ~(-500)eV. The negative ion energy would enhance the directional anisotropic etching of the Cl2 RIE. After etching, remaining thickness of the oxide on the (111) was measured to be ~130nm by scanning electron microscopy.

• 터널과지하공간
• /
• 제24권1호
• /
• pp.1-10
• /
• 2014

본 논문에서 트럭의 고장 발생 가능성과 파쇄기의 처리 용량 변화를 고려하여 노천광산 소밸-트럭 운반시스템의 시뮬레이션을 수행한 사례연구 결과를 제시한다. 강원도 동해시에 위치한 쌍용자원개발 석회석 노천광산을 연구지역으로 선정하고, 시뮬레이션 알고리즘을 설계 하였다. GPSS/H 시뮬레이션 언어를 이용하여 설계된 시뮬레이션 알고리즘들을 콘솔 프로그램 형식의 시뮬레이터로 개발하였다. 또한, 연구지역의 현장조사를 통해 시뮬레이터에 입력되는 인자 값들은 직접 측정하였다. 시뮬레이션 결과 40시간 빈도의 트럭 고장 발생 가능성을 고려할 경우에는 7대의 트럭을 시스템에 투입하는 것이 하루 평균수익을 73,775 USD로 최대화할 수 있는 것으로 분석되었다. 또한, 파쇄기의 처리 용량은 1,300 thp로 운영하는 것이 연구지역의 쇼밸-트럭 운반 시스템의 효율을 높일 수 있는 것으로 분석되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.127-127
• /
• 2011

We investigate the transparent TFTs using a transparent ZnSnO3 (ZTO)/Ag/ZTO multilayer electrode as S/D electrodes with low resistivity of $3.24{\times}10^{-5}$ ohm-cm, and high transparency of 86.29% in ZTO based TFTs. The Transparent TFTs (TTFTs) are prepared on glass substrate coated 100 nm of ITO thin film. On atomic layer deposited $Al_2\;O_3$, 50 nm ZTO layer is deposited by RF magnetron sputtering through a shadow mask for channel layer using ZTO target with 1 : 1 molar ratio of ZnO : $SnO_2$. The power of 100W, the working pressure of 2mTorr, and the gas flow of Ar 20 sccm during the ZTO deposition. After channel layer deposition, a ZTO (35 nm)/Ag (12 nm)/ZTO(35 nm) multilayer is deposited by DC/RF magnetron sputtering to form transparent S/D electrodes which are patterned through the shadow mask. Devices are annealed in air at 300$^{\circ}C$ for 30 min following ZTO deposition. Using UV/Visible spectrometer, the optical transmittances of the TTFT using ZTO/Ag/ ZTO multilayer electrodes are compared with TFT using Mo electrode. The structural properties of ZTO based TTFT with ZTO/Ag/ZTO multilayer electrodes are analyzed by high resolution transmission electron microscopy (HREM) and X-ray photoelectron spectroscopy (XPS). The transfer and output characterization of ZTO TTFTs are examined by a customized probe station with HP4145B system in are.

• 자원환경지질
• /
• 제26권1호
• /
• pp.97-106
• /
• 1993

In order to provide informations for the earth's deep interior and the earthquake mechanism, we have been operating the three components of Streckeisen Seismometers at Pohang Observatory, Korea, as a part of a long period seismic network (POSEIDON) in the northwestern Pacific now under construction. The recording system is specially designed to be able to obtain outputs of broad band and wide dynamic range; BRB (Broad Band), LP (Long Period), and VLP (Very Long Period) output. The triggered BRB and LP signals are digitized with the sampling intervals of 0.1 and 0.4 second, respectively. The lowpass filtered VLP output is digitized and recorded contineously with the sampling interval of 10 seconds. About 120 regional and teleseismic events have been successfully recorded for one and half year since late March, 1991. As a preliminary study, eight events of them are analyzed to determine Rayleigh wave dispersion curves in the period range of 20 to 300 seconds for the continental and oceanic paths. The curves are compared with the typical continental and oceanic ones to discuss the earth's deep interior.

• Journal of Preventive Medicine and Public Health
• /
• 제53권2호
• /
• pp.117-125
• /
• 2020

Objectives: This study investigated the role of information and communication technology and women's empowerment in contraceptive discontinuation in Indonesia. Methods: The study used data from the 2017 Indonesia Demographic and Health Survey and monthly contraceptive calendar data. A Gompertz proportional hazards model was used for analysis. Results: The 12-month contraceptive discontinuation rate was higher among women who had used the Internet in the past year, women who were mobile phone owners, and women who reported having fully participated in household decision-making than among their counterparts. These factors significantly impacted the risk of contraceptive discontinuation in Indonesia, even after controlling for contraceptive method, age, parity, contraceptive intent, education, work status, place of residence, and wealth status. Conclusions: After adjustment for the control variables, a higher risk of contraceptive discontinuation was associated with having used the Internet in the past year, owning a mobile phone, and not participating in household decision-making. Higher contraceptive discontinuation risk was also associated with using contraceptive pills, older age, lower parity, intent of spacing births, more education, current unemployment, and rural residence, and the risk was also significantly higher for those in the lowest household wealth quintile than for those in the fourth household wealth quintile. The association of contraceptive discontinuation with the use of modern information and communication technology and relatively disempowerment in household decision-making may imply that information regarding family planning and contraception should be conveyed via social media as part of setting up an eHealth system. This must include a strong communication strategy to empower and educate women in contraceptive decision-making.