• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.603-609
• /
• 2008

개발품의 품질을 평가하기 위해 무엇을 어떻게 시험할 것인가 적합한 모델을 정하는 것은 중요하다. 개발된 제품의 대부분의 패키지화된 소프트웨어는 소스코드를 공개하지 않으므로 외부적인 동작 특성을 측정하여 평가한다. 고속철도 선로변 정보처리 기기는 단일계로 구성되어 있던 것을 최근에 2중화하므로 신뢰성을 향상하도록 개발하였다. 철도에 사용되는 용품에 대하여 성능 및 안전성을 확보하기 위하여 철도안전법에서 공인시험기관에서 품질인증을 받을 수 있도록 하고 있어 우선 규정의 적용 가능성을 검토를 하였다. 아울러 정보처리모듈 일반 및 전용 그리고 절체기에 대하여 H/W 와 S/W의 검증을 위하여 필요한 절차와 성능을 확인하는 방안을 검토하고, TFM(Track-side Functional Module) Tester기와 Simulator를 활용하여 보드별 성능시험을 하는 방안에 대하여 고찰하고자 한다.

• 한국태양에너지학회 논문집
• /
• 제22권3호
• /
• pp.67-76
• /
• 2002

Data-Acquisition systems are widely used in Photovoltaic(PV) system application in order to analyze and optimize the performance of PV systems. In this paper, the development of a computer-based data-acquisition system and its application are described. The proposed Computer-based data-acquisition System consists of a set of sensors for measuring both environmental and electrical parameters. The collected data are first conditioned and then interfaced to PC using a data-acquisition card. The Labview program was used to further process, display on the monitor at real time and store on the hard disk. We designed and installed two stand-alone PV systems to supply different loads, which in this case a Low Pressure Sodium(LPS) 55 [W] lamp and a electrodless 55 [W] lamp. When the proposed data acquisition system is applied on the designed PV systems, Optimized system operation methods are investigated to confirm a stable load availability and extend battery life time.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 C
• /
• pp.1475-1477
• /
• 1999

The setting of protective relays, which is critical to the system security, requires a huge volume of data and a lot of repetitive calculations. Therefore computerization of this process, named PROSET2000 is in progress in KEPCO. PROSET2000 is based on a power system protection database. The database must accomodate a variety of protective device data efficiently, which need be viewed and updated with ease. This paper suggests several database management functions for PROSET2000.

• International Journal of Automotive Technology
• /
• 제7권2호
• /
• pp.161-166
• /
• 2006

This paper presents shift characteristics of a dual clutch transmission(DCT). To obtain the shift force, dynamic models of the DCT are constructed by using MATLAB/Simulink and considering the rotational inertia of every component and the target pre-select time. Dynamic models of the shift and clutch actuators are derived based on the experimental results of the dynamic characteristics test. Based on the dynamic model of the DCT synchronizer, control actuator and vehicle model, a DCT vehicle performance simulator is developed. Using the simulator, the shift force and speed of the relevant shafts are obtained. In addition, the torque and acceleration of actuators are calculated during the shift process by considering the engaging and disengaging dynamics of the two clutches. It is observed from the performance simulator that uninterrupted torque can be transmitted by proper control of the two clutches.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.167-169
• /
• 2010

추진시스템 전자 제어장치는 추진시스템 내부의 각종 센서신호를 입력 받아 신호처리를 통해 제어알고리즘을 수행하는 장치이다. 기존의 아날로그 센서를 이용한 시스템에서는 센서와 전자제어장치의 전송에 의한 영향으로 신호감쇄가 일어나고 노이즈에 민감한 단점이 있었다. 디지털센서는 센서와 AMP, AD Converter가 하나의 모듈 안에 포함되어 있어 전송선에 의한 영향을 감소시킬 수 있으며, 전자제어장치에서 별도의 S/W 필터를 적용할 필요가 없어 제어 알고리즘의 수행시간을 단축시킬 수 있다. 본 논문에서는 디지털센서를 사용한 전자제어장치의 회로설계 및 제어알고리즘 적용에 따른 신호처리 방안에 대한 내용을 기술하였다.

• 한국기계가공학회지
• /
• 제18권8호
• /
• pp.24-30
• /
• 2019

This study investigated the heat dissipation characteristics of a heat-sensitive LED. The results of the empirical test showed that the best temperature intensification was found at 90 with 15-fins, and the heatsink installed perpendicular to the direction of the flow of air was directly connected to the air in the largest heat shield area, leading to the best cooling, and the number of fin also resulted increase in the heat discharge area, resulting in the largest cooling action with 15 fins. It was found that the rate of air flow changed in the range of 1.5m/s to 2.5m/s, but only by a deviation of about $2^{\circ}C$ to $3^{\circ}C$ from the current state of 15 fins at 2.5m/s, and the rate of air flow increased, but the performance of the heat release was not significantly increased. As a result wind speed with minimum air flow conditions of 1.5m/s can greatly contribute to the heat dissipation performance.

• 한국분말재료학회지
• /
• 제23권5호
• /
• pp.372-378
• /
• 2016

This study focuses on the development of an alkaline leaching hydrometallurgy process for the recovery of tungsten from WC/Co hardmetal sludge, and an examination of the effect of the process parameters on tungsten recovery. The alkaline leaching hydrometallurgy process has four stages, i.e., oxidation of the sludge, leaching of tungsten by NaOH, refinement of the leaching solution, and precipitation of tungsten. The WC/Co hardmetal sludge oxide consists of $WO_3$ and $CoWO_4$. The leaching of tungsten is most affected by the leaching temperature, followed by the NaOH concentration and the leaching time. About 99% of tungsten in the WC/Co hardmetal sludge is leached at temperatures above $90^{\circ}C$ and a NaOH concentration above 15%. For refinement of the leaching solution, pH control of the solution using HCl is more effective than the addition of $Na_2S{\cdot}9H_2O$. The tungsten is precipitated as high-purity $H_2WO_4{\cdot}H_2O$ by pH control using HCl. With decreasing pH of the solution, the tungsten recovery rate increases and then decrease. About 93% of tungsten in the WC/Co hardmetal sludge is recovered by the alkaline leaching hydrometallurgy process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.403-407
• /
• 2009

In this work, finite element investigations were carried out to manufacture a seamless aluminum liner without crack generation using four-stage deep drawing followed by two-stage ironing process. In order to predict the crack generation during the liner manufacturing process, the Normalize Cockroft-Latham(NCL) which is one of ductile fracture criteria was adopted. In addition, the tensile tests were carried out to obtain the critical value of NCL by comparing the experimental and FE simulation results. From this, various case studies based on FE simulation were carried to obtain the optimum die designs which can prevent the crack generation during ironing processes. Finally, the aluminum liner was successfully made using obtained die designs so that requirements were met in terms of thickness and height of the liner.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2973-2978
• /
• 2011

In this paper, a system is developed to support multi-attribute decision making for designing light-weight of rolling stock. Conceptual design of light-weight of rolling stock does not only mean reducing weight. It should be considered about some attributes like safety and environment, technology, etc. So technical attributes and needs of customers, manufacturers and management companies, passengers, should be reflected and qualitative evaluation methods are required. AHP(Analytical Hierarchy Process) and QFD(Quality Function Deployment) are used to decide weighted values of technical attributes and needs from customers. Finally, Alternatives for light-weight of rolling stock that are composed of alternatives of equipment are evaluated by TOPSIS(Technique for Order Preference by Similarity to Ideal Solution). A series of this process are made as a S/W. It could suggest a near-optimal alternative for light-weight of rolling stock.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.665-670
• /
• 2001

The purpose of this study is to develop a new type dryer, which is to proceed mixing and drying of wet-materials at the same time and drying process is carried out in a closed system. In this drying system, thermal contact occurs, when a fluidized zone is created by paddle mechanism. Accordingly, wet-materials is dried in a short time without any damage. Also wet-materials could be dried uniformly to low moisture contents. It is suitable to dry a small quantity of multi-kind materials. And drying process is carried out in a closed system, so as for environmental pollution dust not to be emitted into the atmosphere. Accordingly, it could be used to dry not only food and chemical materials, but also environmental pollution materials.