• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.1232-1240
• /
• 2001

In this study. a computer simulation of the Korean High Speed Prototype Test Train was performed to investigate the dynamic behavior(running stability. safety and comfort) in detail design process. The simulation model which was prepared by ADAMS/Rail V10.l consists of power car and middle car assembly (2 motorized cars ＋ 3 trailer cars). The nonlinear analysis takes into account the full vehicle model including wheel/rail contact and the influence of disturbed track. Throughout the dynamic calculation of KHST on the straight and the curved track. accelerations in car body. ride comforts and wheel rail forces were investigated.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.970-978
• /
• 2010

In this study, interior noise of the high speed EMU was estimated by statistical energy analysis (SEA) method. Based on the data measured at a distance of 25m from a running train, exterior noise of the running train was calculated. And then it was designed as noise sources in VA ONE, a commercial software of SEA. coupling and damping loss factor of high speed EMU studied in previous studies is used. The interior noise of the train was estimated for a open-land section. The analysis of interior noise of HST in the tunnel section will be estimated through same method.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.813-819
• /
• 2008

For the wear characteristics assessment of Saemaul train passing through curves, an analysis model for multi-car system has been developed. By using this model and ADAMS/Rail, sensitivity analyses have been conducted for the wear characteristics by changing the related parameters. According to the increase of running speed, the wear number, the sliding mean and friction coefficient were increased. At high speed, the wear number, the sliding mean and friction coefficient of left wheel showed higher than right wheel. If the cant increased, the wear number the sliding mean and friction coefficient increased. but decreased based on the balance cant value by the curvature and running speed.

• 전기의세계
• /
• v.17 no.4
• /
• pp.7-12
• /
• 1968

In recent years the development of the SCR has made possible the control of the power system. It is one example that the speed control of the induction motor can be done by changing the frequency with the S.C.R. This paper is devoted primarily to a study of the running characteristics of the single phase induction motor through the experimental and theoretical methods when the speed of the motor is controlled by varying the conduction period in current with S.C.R. under the constant frequency. We conclude from the experiments that the adjustment of the phase angle in current is equivalent to the change of the supply voltage to the motor. Therefore, the speed control of the motor such as a fan duty motor is possibly by this methods.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.507-509
• /
• 2015

In this paper, a novel method of sensorless control scheme is proposed to apply on a single phase hybrid SRM used in high speed operation. The proposed method utilizes beneficially permanent magnet field whose performance is motor parameter independent to estimate the rotor position. Also, the current slope is adopted to complete the sensorless control when the motor running with heavy torque at high speed condition. Through this approach, the adjustable turn on/off position can be achieved without prior knowledge of inductance profile which is always employed by many sensorless schemes. And this paper may offer an available method to do the sensorless control in hybrid SRM used for high speed running.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.810-813
• /
• 2003

The present headway on KNR(Korea National Railway) lines varies from 6 to 10 minutes depending on the each line and by the operation of High Speed line in 2004, the bottleneck would be expected within a few sections such as Daejeon-Daejeon shunting yard which will be the common mute between KTX(Korea Train Express) and conventional trains. Therefore, KNR would like to reduce the headway of the all lines by 4 minutes with the implementation of ERTMS/ETCS on-board system. Where ETCS(European Train Control system), the subsystem of ERTMS, is Automatic Train Protection system for safety train running. This study will be analyze expected braking distance and running time depending on characteristics of conventional passenger and freight trains and high speed train will be operated within electrified conventional line for comparing the headways of ATS(Automatic Train Stop) system and ETRMS/ETCS system within the Daejeon-Daejeon shunting yard section.

• Journal of the Korean Society of Safety
• /
• v.27 no.3
• /
• pp.167-175
• /
• 2012

For establishing a standard of design element of the smart highway, this study investigated driver's anxiety EEG according to running speeds and geometric designs. Also, the experiment was implemented on 60 subjects. Based on running speed data and brainwave data, which were obtained from the experiment, this study analyzes anxiety EEG according to running speeds and geometric designs, and finally draws a forecasting model of anxiety EEG by selecting affecting factors of anxiety EEG. Forecasting model shows that left curve is the most influential on anxiety EEG figure. The reason is because when driver is driving on the first-lane, his or her visibility is impeded by a median strip. For this reason, anxiety EEG figure increases. And also steep downward slope and large radius of curve are heavily influential on driver's anxiety EEG figure. It is judged that anxiety EEG figure is increased by high speed on those section. Thus, the forecasting model of anxiety EEG suggested on this study will be utilized for design phase, and will decide the design speed on the superhighway. So, it will be used to make practical and safety road.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.6
• /
• pp.723-730
• /
• 2013

The speed-limit regulation on a turnout is the main factor inhibiting the speed-up of conventional lines. The specified speed for a train moving through a turnout system is lower than that for a train traveling over the general track. This is done to ensure the running safety of a railway vehicle moving through a turnout. In this study, the shape change example of the guard rail component of a turnout in the Daegu Metropolitan Transit Corporation (DTRO) system was studied. A theoretical examination of the geometrical interaction formula according to wheel/rail shape at the turnout was conducted. Running safety analysis by changing the length of the guard rail on the F10/F12 turnout using the developed analysis techniques (by VI-Rail) was achieved, and the effect on railway safety was examined accordingly.

• Journal of the Korean Regional Science Association
• /
• v.6 no.1
• /
• pp.57-68
• /
• 1990

The purpose of this study is to develop the models to predict the noise PCE (Passenger Car Equivalence) of large running vehicles through noise prediction models. The noises were measured at the distance of 7.5M, 11.0M, and 14.5M from the noise source with test vehicles running at the speed of 40 Km/h, 60 Km/h, and 80 Km/h while normal traffic were detoured. Total noise levels were measured while vehicles were running at given speeds, Engine noise level was considered as the noise of its idle running at the three vehicle speeds shown above friction noise level was ascertained by moving the vehicle at given speeds without the engin operating. The noise prediction models for each noise source were developed by factors which affect to the each noise level. As a result of this paper, the reduction of total vehicle noise by increasing the distance to the noise source from 10 M to 15 M is as much as that by dropping its speed from 60 Km/h to 40 Km/h. Also, the reduction of PCE of total noise of large vehicle by making the noise source to that by reducing its speed from 80 Km/h to 60 Km/h. Enging noise PCE, which is in range between 65 and 160, is larger than friction noise PCE which is in range 3.5 and 5.5. Engin noise is the main noise of the large vehicles while friction noise is that of the small vehicles. Machine noise for large vehicles, and engin noise for small vehicles should be tightly controlled to reduce the vehicle noise. A low noise engine and tire, and the shape of vehicle body are needed to be developed to reduce noise further.

• The Research Journal of the Costume Culture
• /
• v.22 no.2
• /
• pp.290-299
• /
• 2014

This research sought to analyze the characteristics of breast movement at the treadmill activity levels. It also examined the effect of wearing a sports bra in reducing breast displacement. The subjects for the data collection were females in their 20s (n=2) with C-cup size breast. The experimental conditions were three different moving speeds (4 km/h, jogging: 7 km/h, and sprinting: 10 km/h) and two types of sports bras. Three dimensional breast displacement was measured. The displacement of the right nipple point was measured with a 3D motion analyzer. The results show that the breasts were greatly displaced from the walking speed (4 km/h) when subjects did not wear any bra. Whereas their breast displacement distance decreased remarkably when they wore sports bras. The nipple point moved 42~44 mm in the vertical direction at walking speed with naked condition. But it was reduced by 80% after wearing sports bras. When subjects running (7 km/h, 10 km/h) without any bra, the nipple point moved 122~141 mm. However it was reduced by 60~70% when they wore sports bras. The apartment time (time delay) between at the highest point of the upper body and the nipple was 0.25 seconds at the running speeds (7 km/h, 10 km/h) without wearing any bra. After wearing sports bras, the time delay was cut to 0.06~0.12 seconds. These results implies that without wearing any bra the skin surrounding the breasts might be seriously pulled at running activity. The functional sports bra suppress breast movement. It might prevent the sagging of breasts by preventing the damage of the Cooper's ligaments.