• Journal of Ship and Ocean Technology
• /
• v.8 no.2
• /
• pp.1-12
• /
• 2004

To keep the ocean environment from pollutions, strict international requirements on the controllability are arisen to the VLCC. Especially in low speed operations near the harbor, the VLCC is often supported by tug to replenish the insufficient rudder force. When water jet is blown to the flapped rudder, the Coanda effect induces a high-lift force by delaying stall and re-enforcing circulation in a large angle of attack (Lachmann 1961, Ahn 2003). Based on numerous research efforts, the rudder system supported by the Coanda effect was devised and its performances were evaluated in the towing tank for a large VLCC model. Hydrodynamic forces acting on the rudder system were measured with a water jet blowing on the rudder surface and compared with those acting on a conventional rudder. The effectiveness of the new rudder system was proven through an experimental evaluation.

• Journal of Navigation and Port Research
• /
• v.29 no.10 s.106
• /
• pp.839-845
• /
• 2005

A rudder roll control system is developed and analyzed to control the yawing and rolling motion of ship in irregular waves. The 4-DOF maneuvering equations of motion are derived to carry out the simulation of the motion of a ship and the wave forces are considered as the external forces of a ship in the simulation. The wave forces in the time domain analysis are generated from the frequency transfer function calculated by 3-D source distribution method. The rudder roll control system is developed by linear combination of PD rudder controllers of yawing and rolling motion. Rudder rate speed and Schilling rudder are considered to increase the roll reduction efficiency.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2005.10a
• /
• pp.55-61
• /
• 2005

A rudder roll control system is developed and analyzed to control yawing and rolling motion of ship in irregular waves. The 4-DOF maneuvering equations of motion are derived to carry out the simulation of the motion of a ship and the wave forces are considered as the external forces of a ship in the simulation. The wave forces in the time domain analysis are generated from the frequency transfer function calculated by 3-D source distribution method. The rudder roll control system is developed by linear combination of PD rudder controllers of yawing and rolling motion Rudder rate speed and Schilling rudder are considered to increase roll reduction efficiency.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1647-1650
• /
• 1997

This paper presents the control law of Automatic Rudder Trim System(ARTS) for the KTX-1. The proposed ARTS is designed mainly t reduce the pilot's work load for trimming in the various conditiions of engine torque. airspeed, and aircraft configuration. The ARTS partially compensates the transient yawing motion due to change of engine power in turboprop aircraft because of the limitation of the actuation speed of the trim motor. In this paper flight test data are analyzed to understand the phenomena and the dynamics of the reversible rudder flight control system is derived. Finally, the control concept and conrtol law of ARTS are described and the characteristics of the ARTS are analyzed through simulation study.

• Journal of Navigation and Port Research
• /
• v.31 no.4
• /
• pp.289-293
• /
• 2007

In this paper, new application of adaptive neural network to design a ship's Rudder-Roll Damping(RRD) control system is presented Firstly, the ANNAI neural network controller is presented. Secondly, new RRD control system using this neural network approach is developed. It uses two neural network controllers for heading control and roll damping control separately. Finally, Computer simulation of this RRD control system is carried out to compare with a linear quadratic optimal RRD control system; discussions and conclusions are provided. The simulation results show the feasibility of using ANNAI controller for RRD. Also, the necessity of mathematical ship model in designing RRD control system is removed by using NN control technique.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.5
• /
• pp.577-585
• /
• 2015

This paper deals with development of an autopilot system for leisure yacht based on NMEA 2000 network and android platform. The developed system can operate both for manual steering and automatic navigation mode. In automatic steering mode, after manipulation of commands which are NMEA 0183 sentences by android platform, the developed system translates and sends the packets through NMEA 2000 network. Then the controller which is connected to NMEA 2000 network receives the commands and controls the boat's rudder system automatically. The automatic steering mode is achieved by cooperation of two controllers; one for controlling the rudder system, and the other for controlling the vessel's heading. To control the vessel's rudder and heading angle two PID controllers are developed with an adjustable dead-band gain. Also, in order to eliminate the steady-state error occurred by applying dead-band, an integral controller which specifically supervises the system's behavior inside the dead-band area is developed. In this paper, at the first stage, simulations are accomplished using computer in order to examine the feasibility of the proposed based on simulation results. In the next step, the system on a real hydraulic steering model is implemented and at the end the performance examination by implementing it on a real boat and doing test navigation is executed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.1
• /
• pp.121-131
• /
• 1999

Automatic Rudder Trim System(ARTS) is a device to reduce the pilot's work load for rudder trimming greatly required in varying abruptly aircraft's engine power. This paper represents a technical analysis and a design of control law of the ARTS. The control law of the ARTS is designed based on the analysis of aircraft's characteristics, system's requirements, and limitations. The control law is comprised of open loop control using the rudder trim map for a specific aircraft and closed loop control to compensate the error of the open loop control system. flight test results show that the ARTS can reduce pilot's work load for rudder trimming dramatically and can compensate the aircraft's transient yaw motion.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.2
• /
• pp.122-131
• /
• 2010

The increasing size and speed of cargo ships result in high speed flow in propeller slipstream, and thereby cavitation is frequently observed on and around a rudder system. Rudder gap cavitation is the most difficult one to control and suppress among various types of the cavitation on a rudder system. In the present study, experiments of the incipient cavitation and pressure measurement were carried out for typical cargo ship rudder sections with and without the suppression devices, which were suggested by the authors. Fundamental understanding of the rudder gap cavitation inception was obtained along with its relevance to the surface pressure distribution. It is confirmed that the gap flow blocking devices effectively suppress the rudder gap cavitation and, at the same time, augment lift.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.2
• /
• pp.115-121
• /
• 2002

This report summarized the static test of the rudder system for the KTX-1 basic trainer. The test loads are applied up to the limit and ultimate loads in a stepping sequence. Test loads and test results matt the strength and stiffness requirements of the rudder control system.. Using #004 full scale structure test airframe.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.8
• /
• pp.1285-1290
• /
• 2017

In this paper, we developed a core module of the steering system to control and operate the outboard ship with the automatic steering system, and implemented it as a complete integrated system. In particular, this paper presents the problem of the rudder sensor used in the existing system and implements the contactless rudder sensor as an improvement. In the case of existing rudder sensors, there is a problem that safety operation and economic loss of the ship operation is caused by malfunction due to immersion during use in outboard vessels. However, the proposed rudder sensor is separated from the rotary shaft to constitute a contactless type, and a circular magnet is fixed so that the rotating value can be detected and used by the Hall sensor to completely solve the flooding problem. As a result of the characteristic test, the voltage value from 1.8V to 3.2V was obtained between $-35^{\circ}$ and $+35^{\circ}$ degrees and satisfied the reference value. The proposed rudder sensor was mounted on the outboard ship, and all the performance of controller system were checked. According to the system proposed in this paper, it satisfies the Korean Standard Specification, which defines the speed of convergence in 30 seconds by switching from left to right in 7 seconds. We also confirmed that automatic steering was performed by comparing the compass sensor with the destination in the integrated controller at the start-up.