• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.843-850
• /
• 1991

There is a growing demend for absorptive electromagentic shielding materials for wide band frequency application. In this study, the absorber which consists of a rubber plus Ni-Zn ferrite which have been prepared by direct-wet method. A rubber ferrite composite for electromagnetic shielding, it is most importan facter the homogeneous ultra fine size and high dispersitive ferrite powder. Direct-wet method and solid-solid reaction method for preparing of ultra fine ferrite powder was used. It has been experimentally verified that the powder which prepared by direct-wet method was very fine and almost same size spherical powder, the composite ferrite have excellent electromagnetic wave absorption in X-band.

• Electrical & Electronic Materials
• /
• v.9 no.4
• /
• pp.344-350
• /
• 1996

Tracking is one of the biggist problems to be overcome in polymeric materials for outdoor insulators. But It can be decreased with the addition of filler such as alumina trihydrate (ATH). In this paper, the tracking of surface and evaluation of insulating ability at silicone rubber is investigated, using the salt fog test. At initial state, the peak leakage current and numbers by dry band arcing is increasing with increasing the filler level, but at aged state decreasing at high concentration filler samples. This is because the roughness of the surface may contribute to the increase in peak leakage cur-rent and numbers. As increasing the filler level, the insulating ability of materials is higher and weight loss is decreased. The mechanism of insulating failure is occurred by the erosion than the tracking and the erosion caused weight loss of 2 g.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.501-504
• /
• 1997

We investigated the tracking and erosion resistance of the silicone rubber by Inclined-Plane Method. And. with the variation of experiment time, the chance of the leakage current waveform was evaluated. The typical leakage current waveform was the form of mixture of sinusoidal wave and rectifying wave. It is thought that the sinusoidal wave is due to conductivity of contaminant when wet. and the rectifying wave is due to arc of dry band.

• Journal of Powder Materials
• /
• v.20 no.2
• /
• pp.125-128
• /
• 2013

Magnetic and dielectric properties of rubber composites are controlled by using two kinds of high-permeability metal particles with different electrical conductivity (Sendust, Permalloy), and their effect on microwave absorbance has been investigated, focusing on the quasi-microwave frequency band (0.8-2 GHz). Noise absorbing sheets are composite materials of magnetic flake particles of high aspect ratio dispersed in polymer matrix with various filler amount of 80-90 wt.%. The frequency dispersion and magnitude of complex permeability is almost the same for Sendust and Permalloy composite specimens. However, the complex permittivity of the Permalloy composite (${{\varepsilon}_r}^{\prime}{\simeq}250$, ${{\varepsilon}_r}^{{\prime}{\prime}}{\simeq}50$) is much greater than that of Sendust composite (${{\varepsilon}_r}^{\prime}{\simeq}70$, ${{\varepsilon}_r}^{{\prime}{\prime}}{\simeq}0$). Due to the large dielectric permittivity of Permalloy composite, the absorbing band is shifted to lower frequency region. However, the investigation of impedance matching reveals that the magnetic permeability is still small to satisfy the zero-reflected condition at the quasi-microwave frequency band, resulting in a small microwave absorbance lower than 10 dB.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.306-309
• /
• 2003

Carbon uses included (32 wt %) Silicone Rubber, use different composition and thickness and investigated effect and special quality that get to electromagnetic absorber to sintering style Ba Ferrite that have composition of Fe$_2$O$_3$: $Ba_2$CO$_3$= 82.1 : 17.9 wt% to develop high efficiency X-Band electric wave absorber

• Elastomers and Composites
• /
• v.13 no.2
• /
• pp.99-107
• /
• 1978

The measurement of the infrared absorption spectrum of supporting reinforcing filler which is oltained from the domestic area of Korea, Japan and U.S.A., is used by the method of KBr pellet. As a result of experiment, each absorption fond of the filler had appeared differently, because of each filler is consisted of different chemical composition, different crystalline form, different method of preparation, and the different ways of use etc. According to the above phenomena, each filler seems to have a different characteristic infrared absorption band, We can find what filler is used for sample rubber.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.12 no.1
• /
• pp.1-10
• /
• 1999

In this paper, we have investigated the effects of the environmental factors on Low Molecular Weight (LMW) silicone fluid contents existing in high temperature vulcanized (HTV) silicone rubber sample, using dipping method and contact angle, current measurement. Artificial treatments such as immersion in water, elevated temperature, UV irradiation and dry band arcing under salt-fog condition are selected as the environmental factors. This results will be helpful to investigate the degradation with time and to expect a life time, because the LMW silicone content, which is important to recovery the hydrophobicity of silicone rubber surface, show different results by each environmental factors.

• Earthquakes and Structures
• /
• v.24 no.3
• /
• pp.193-204
• /
• 2023

The concept of meta-material-based isolation systems (MMIS) for structural columns has been revisited in the present study in order to enhance the stability of rubber pads by using steel shim reinforced rubber (SSRR) layers. Analytical calculations have shown a significant improvement in the stability of MMIS with SSRR pads. Finite element analysis has also been conducted to further show the reduced response of a bridge with the modified MMIS under excitations having frequencies within the corresponding attenuation zone (AZ) as compared to the response of a conventional bridge without MMIS. FE analysis further shows the stress generated on the bridge with MMIS systems are within safe limits. Finally, a generalized procedure has been developed to design bridge columns with the proposed modified MMIS.

• The korean journal of orthodontics
• /
• v.21 no.3
• /
• pp.563-580
• /
• 1991

The purpose of this study was to investigate and compare the biomechanical properties of orthodontic rubber elastic materials. Latex bands, nylon-covered elastic threads and polyurethane-based elastic modules, delivering $205{\pm}10$ grams force at 30mm stretching state were selected and stored separately in 3 environments-air ($22{\pm}3^{\circ}C$), distilled water ($37{\pm}1^{\circ}C$), or natural saliva ($37{\pm}1^{\circ}C$). And, the amount of remaining force and permanent elongation of each sample were measured on Instron at interval of 1 hour, 6 hours, 12 hours, 24 hours, 1 week, and 2 weeks. So the data derived were analyzed statistically. The results were as follows: 1. Force decay and permanent elongation of all materials increased with time lapsed; elastic module, latex band and nylon-covered elastic thread in that order of the amount of force decay; elastic module, elastic thread, latex band in that order of the amount of permanent elongation. 2. Among environmental conditions, force decay and permanent elongation in natural saliva, most increased, and those in air, least increased. 3. There was a negative correlation between force decay and permanent elongation. 4. Force decay and permanent elongation were most affected by the material itself, time and environments in that order. 5. After 24 hours in saliva, the percentage of remaining force in elastic module was 51.9% (107.37grams); in latex band, 83.2%(172.62grams); in elastic thread, 85.0%(179.25grams). After 2 weeks in saliva, the percentage of remaining force in elastic module was 42.9%(88.75grams); in latex band, 74.5%(154.50grams); in elastic thread, 77.6%(163.75grams).

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.724-726
• /
• 1992

In this paper, the permeability ($\mu_{\tau}'$, $\mu_{\tau}''$), dielectric constants($\varepsilon_{\tau}'$, $\varepsilon_{\tau}''$) and absorbption characteristics of Ferrite/Rubber 0-3 composites were investigated. The composite specimens were prepared by molding and curing the mixtures of matrix rubber and Ni-Zn ferrite powders which were synthesized by wet-direct method. The permeability ($u_{\tau}'$) of specimen was decreased from 2.58 to 0.7 in the range of 1$\sim$7(GHz) and kept constant 0.7$\sim$0.8 at higher than 7(GHz), the higher the frequency was, the less the valves of $u_{\tau}"$ was from 1.57 to 0.03. The optimum thickness of microwave absorber, utilizing the Smith chart, was 5(mm). The reflection loss shows over than 20(dB) from 5.5(GHz) to 7.5(GHz) at 5(mm) thickness and relative band width(B/fm) was about 30%.