• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.1003-1011
• /
• 2009

Transverse flux machine(TFM) has been developed to drive a machine of large input power at low-speed. However, it has complicated structure and large torque ripple due to its inherent structure. In this paper the characteristics of torque of a rotatory two-phase TFM are analyzed by using the 3-dimensional finite element method and optimal design. This research shows that one of the effective design variables is the skew angle of permanent magnet. The skew angles of permanent magnet are optimized by using a genetic algorithm. It also shows that the proposed optimal skew magnet not only increases average torque but also decreases torque ripple of a rotatory two-phase TFM.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.216-222
• /
• 2002

Brake Moan is a laud and strong noise occurring at any vehicle speed over 2 mph as a low frequency in below 600Hz. In this study, we targeted to shift the unstable mode that causes the brake moan from the moats frequency range to sufficiently higher frequency range to avoid the moan phenomenon. We simulated the finite element model and found out the nodes in which the brake moan occurs the most and we regarded the boundary and its relationship between the brake pad and the rotor as a spring coefficient k. With the binary set of the spring coefficient k, we finally used genetic algorithm (GA) to get the optimal topology of the brake pad and its shape to avoid the brake moan. The final result remarkably shows that genetic algorithm can be used in topology optimization procedures requiring complex eigenvalue problems.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.86-88
• /
• 2007

By reason of variation magnetic field, cogging torque is generated. Cogging torque of Spoke type motor is bigger than other type permanent magnet motor. So, this paper presents a design notch on stator and variation rotor shape to reduce cogging torque of Spoke Type motor. Through Fourier formulation of magnetic field on air gap, we found position of notch. The validity of the proposed design is confirmed with FEM analysis method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.12
• /
• pp.125-132
• /
• 2013

This paper has done a three-dimensional FEM analysis of the PM claw pole stepping motor. As magnetization happens in the z-axis, which does not have a constant value, three-dimensional FEM analysis is necessary for characteristic analysis of PM claw pole stepping motors. Because it is a type of permanent magnet motor, the PM claw pole stepping motor naturally has a detent torque. This torque is known to show negative effects on motor performance. To improve motor performance, reducing the detent torque is very important during the motor design. This paper applied DOE for optimization of stator pole design of the motor. Also, we compared motor performance by applying a different type of rotor shape, dividing the permanent magnet. To verify the simulation results, an experiment was done.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.924-926
• /
• 2001

This paper presents the characteristics of current harmonics and torque ripple of Brushless DC motor, which is developed the fan blower of vehicles, according to permanent magnet shape input voltage wave form. To investigate the torque ripple and the phase current harmonics, these characteristics is analysed and compared the experimental results. In the process of analysis, FEM is introduced and computed a transient state torque of BLDC with a sinusoidal and a PWM wave voltage.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.780-782
• /
• 2001

SRM은 회전자의 구조가 간단하고 간단한 제어장치로 구동이 가능한 장점이 있지만 Cogging Torque로 인한 소음, 진동, 토크리플 등으로 인해 SRM의 안정화 운전에 장애가 되는 단점이 있다. 이를 제거하기 위한 방법으로는 외부회로에 제어기를 도입하여 전류파형을 조절하는 방법이 있으나 이 경우 고가의 복잡한 정밀제어기를 부착해야한다. 본 연구에서는 회전자의 형상을 조절하여 Cogging Torque를 감소시키는 방법을 연구한다. 이를 위하여 유한요소법을 이용하여 설계변수의 민감도를 계산하고 최적화 기법을 사용하여 형상변경 실시를 반복하여 최적설계를 하고자 한다.

• Journal of Aerospace System Engineering
• /
• v.6 no.1
• /
• pp.1-6
• /
• 2012

During helicopter rotor system development process, whirl tower test is conducted basically. For conducting whirl tower test during bearingless hub development process, design new blade or using existing blade with repair or remodeling. Because simple shape and efficient aerodynamic characteristic, BO-105 blade is used for hub system development widely. Originally BO-105 Blade is used for hingeless hub, so flap stiffness and lag stiffness on blade root area is relatively low. So appling BO-105 blade to bearingless hub whirl tower test, root area have to be reinforce. In this paper, suggest reinforcement method of BO-105 blade root area.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.3
• /
• pp.253-259
• /
• 2004

A numerical investigation was performed to determine the effect of airfoil on the optimum flap height using NACA0015 Wells turbine. The five double flaps which have 0.5% difference were selected. A Navier-Stokes code, CFX-TASCflow, was used to calculate the flow field of the Wells turbine. The basic feature of the Wells turbine is that even though the cyclic airflow produces oscillating axial forces on the airfoil blades, the tangential force on the rotor is always in the same direction. Geometry used to define the three dimension numerical grid is based upon that of an experimental test rig. This paper tries In optimized disign the double flap of Wells turbine with the numerical analysis.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.12
• /
• pp.700-708
• /
• 2004

Flux-reversal machine (FRM) is a new doubly-salient stator-permanent magnet (PM) machine with flux linkage reversal in the stator concentrated windings. It can operate in both motoring and generating modes. In this paper, a novel design technique to improve the performance of FRM is proposed. Proposed techniques have a new stator winding and a magnet arrangement method. The stator and rotor shape with a concave type and a flux barrier are also proposed. According to the experimental results, it is shown that the proposed FRM have an improved performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.321-321
• /
• 2010

In this paper, we propose a novel type shaft-less ring type ultrasonic motor. A traveling wave rotary type ultrasonic motor is selected as a base model. The newly designed stator has two piezoelectric ceramic rings which are bonded in sandwich shape as traveling wave generator. So, we can expect to produce higher torque. The proposed model has the rotor structure that coupled with the stator provokes the pressure, this model do not install the separate plate any spring device. We used the finite element method to verify the operation principle and to compute the vibration mode of proposed model.