• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.304-307
• /
• 2001

This Paper describes a method for indirect sensing of the rotor position in switched reluctance motors(SRM's) using only current sensors. The detailed operation and simulation of this technique is shown. In particular, current waveform should have at least one peak and estimate the speed and rotor position by detecting position. The simulation result shows that the technique can gives the information of rotor position.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 A
• /
• pp.64-66
• /
• 1999

Switched reluctance motor(SRM) has the advantages of simple structure, low rotor inertia and high efficiency. However, position sensor is essential in SRM in order to synchronize the phase excitation to the rotor position. The position sensors increase the cost of drive system and tend to reduce system reliability. This paper investigates the speed control of sensorless SRM in which the phase current and change rate are utilized in position decision, and the period of dwell angle is variable by compensating the rotor angle. The proposed system consists of position decision, phase locked loop controller, switching angle controller and inverter. The performances in the proposed system are verified through experiments.

• 한국정밀공학회지
• /
• 제24권6호
• /
• pp.78-85
• /
• 2007

In this study, we performed finite element analysis for the design of a medical centrifuge and two-types of centrifuge were compared with each other. The types of centrifuge are 2-arm straight type and 3-arm type. Structural analysis was done with respect to the change of the rotational speed of the rotor of a centrifuge. When the rotor of centrifuge was rotated, the von Mises stress of 2-arm straight type-rotor was compared with the von Mises stress of 3-arm type. The margin of safety was estimated from the result. We found the critical speed of centrifuge from the campbell diagram by modal analysis.

• 전기학회논문지
• /
• 제60권11호
• /
• pp.2035-2042
• /
• 2011

In this paper, we proposed the outer-rotor type of FSPM motor for high speed operation and optimized motor shape. First of all, combinations of pole and slot numbers are examined for the optimal back-EMF and cogging torque, then optimizes the better shape design of the permanent magnet, rotor pole width. Further, The winding turns are obtained by circle of the voltage limit equation and motor parameters to minimize the current and to improve the efficiency. As a result, the performance of the designed model is satisfied, and it is verified through a two-dimensional finite element method (2D-FEA).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.311-313
• /
• 1996

In case of field weakening region, the dynamic behavior of the speed controller depends on the rotor flux level. In this region, the flux is decreased inversely proportional to the rotor speed. As the rotor flux is decreased, as the magnetizing inductance is increased. In this paper, the effect of this increased magnetizing inductance to the performance of vector control is illustrated. The stationary reference frame torque not including the magnetizing inductance is calculated by stationary stator flux, and the rotating reference frame torque including the magnetizing inductance is calculated by rotating rotor flux. If the magnetizing inductance value is constant, two torque values are same regardless of the flux-component current. However, if the magnetizing inductance is varied, those two values are different. The paper presents the new tuning scheme of the magnetizing inductance using the difference between the stationary and rotating torque. Computer simulation demonstrates the efficacy of the proposed scheme.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 추계학술대회논문집; 한국과학기술회관, 8 Nov. 1996
• /
• pp.313-318
• /
• 1996

In this paper, a parametric study of the unbalance response and the stability is carried out to show the influence of seal parameters on the response of rotor. The seal parameters optimized are the seal clearance and the seal length. The minimum quantity of a Q factor in the critical speed and the maximum quantity of a logarithmic decreement in the operating speed, avoiding the reign of resonance, are the objective function. This paper describes a new approach to find a seal parameter of rotor system. The optimization method is used genetic algorithms, which are search algorithms based on the mechanics of natural selection and natural genetics. The results show the capability of this method and indicate that an optimal design of seals can improve the unbalance and the stability of rotor.

• 한국정밀공학회지
• /
• 제12권9호
• /
• pp.137-147
• /
• 1995

The unbalance response analysis is one of the essential area in the forced vibration analysis of rotor-bearing systems. Local bearing parameters in rotor-bearing systems are the major sources which give rise to a difficulty in unbalance response computation due to the complicated dynamic properties such as rotational speed dependency and anisotropy. In the present paper, an efficient method for unbalance responses is proposed so as to easily take into account bearing parameters in computation. An exact matrix condensation procedure is proposed which enables the present method to compute unbalance responses by dealing with condensed, small matrices. The proposed method causes no errors even though the computation procedure is based on the small matrices condensed from the full matrices. The present method is illustrated through a numerical example and compared with the conventional method.

• 한국산학기술학회논문지
• /
• 제16권4호
• /
• pp.2344-2349
• /
• 2015

여름철이 고온 다습한 우리나라에서는 잠열부하가 크기 때문에 에어컨만을 사용하면 냉방에너지를 많이 사용하게 된다. 이 때에 제습기를 동시에 사용하면 냉방 중 큰 비중을 차지하는 잠열부하를 줄일 수 있어 실내 공기질도 개선하고 냉방에너지도 절약할 수 있다. 본 연구에서는 가정용 제습기에 사용되는 무기섬유 기질에 메탈 실리케이트가 함침된 소형제습 로터에 대하여 항온항습실에서 로터 회전속도, 재생 공기온도, 실내 공기온도, 실내 상대습도, 제습부 전방풍속을 변화시키며 제습 성능을 측정하였다. 제습 로터는 최적 회전수 (1.0rpm)가 존재하며 최적치를 초과하면 불완전 재생 등으로 제습량이 급격히 감소한다. 재생온도가 높아질수록 재생에는 유리하나 제습-재생과정의 열적인 편차가 급격히 증가하여 제습량이 감소한다. 따라서 최적 재생온도가 존재하는데 본 연구의 경우는 $100^{\circ}C$로 나타났다. 상대습도의 증가에 따라 제습량도 증가한다. 이는 제습제의 제습능력이 상대습도에 의존하는 때문이다. 실내 공기온도의 증가에 따라 제습량도 증가한다. 이는 제습측 온도가 높을 때 재생측 공기와의 열적 편차가 감소하여 제습부의 상당량이 제습에만 사용될 수 있기 때문이다. 전방풍속의 증가에 따라 제습량도 증가한다. 이는 전방풍속의 증가에 따라 열 및 물질전달계수가 증가하기 때문이다.

• Journal of Mechanical Science and Technology
• /
• 제15권2호
• /
• pp.152-159
• /
• 2001

In this paper it is intended to set-up a sound model of the 60,000rpm 100kW prototype APU gas turbine rotor-bearing system, and particularly to investigate the influences of the tie shaft on the rotordynamic characteristics of the entire APU gas turbine rotor-bearing system, employing the dual shaft model. Firstly, a mock-up APU rotor has been constructed to test and verify the model. Analytical natural frequency results have agreed with the corresponding modal test ones to within 5% difference. Then, the rotordynamic characteristics of the prototype APU rotorbearing system have been investigated. Natural vibration and unbalance response analyses results have shown that the inner tie shaft resonance can cause high enough vibration of the outer main rotor shaft. This could be a concern as the rotor journals operate on very thin air film at high speed. It is concluded as a conservative design practice that the inner tie shaft should be explicitly modeled in the rotordynamic analysis of the APU rotor-bearing system.

• 제어로봇시스템학회논문지
• /
• 제11권3호
• /
• pp.193-199
• /
• 2005

VTOL(Vertical Take-Off and Landing) aircraft is attractive due to the reason that it is not necessary to have long runway. However a rotorcraft has a definite limitation to fly at the high speed due to the stall at the tip of rotor. To solve this problem, tilt rotor, tilt wing and lift fan were researched and developed. It was verified that the tilt rotor aircraft among them was more effective in disk loading. On this basis, the tilt rotor aircraft has been made into XV-15, V-22, BA-609 and Eagle Eye. This paper shows a nonlinear simulation program for general tilt rotor aircraft that was developed in order to validate the flight characteristics of tilt rotor aircraft and verified through the simulation analysis.