• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.263-266
• /
• 2005

The critical speeds and mode shapes are most important to determine the behaviors of rotor in designing rotating machinery. As the capacity and the span of turbine-generator increases, the turbine-generator system has many components such as bearings, pedestal, turbine and baseplates etc. and it is getting flexible and has many critical speeds. Especially, the characteristics of bearing-pedestal are very complicated and then they affect the entire vibration characteristics of turbine-generator system. In this paper, it is observed how to determine the equivalent dynamic stiffness of bearing-pedestal by analytic and experimental method.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.64-69
• /
• 1997

정격속도 100,000RPM용 원심분리기(centrifuge) 로터베어링계에 대해 회전체동역학 해석이 수행된다. 시스템은 원심분리기 로터, 유연축, 모터 로터와 축, 그리고 모터축 지지용 두 개의 구름베어링으로 구성된다. 설계목표는 정격속도가 위험속도(critical speed)에 대해 충분한 분리여유를 갖고, 위험속도에서 로터의 양호한 불균형응답특성을 이루어 내는 것이다. 후자의 요구조건은, 시스템이 다수의 위험속도를 통과하며 정격속도 주위에서 충분한 분리 여유를 갖지 않을 수도 있기 때문에 특히 중요하다. 시스템에 초유연축(extra-flexible shaft)을 도입함으로써, 비록 1차 위험속도에서 만족스럽지 못한 큰 불균형응답을 가질지라도 고차 위험속도에서 만족스런 작은 불균형응답을 보인다. 1차 위험속도에서 로터의 큰 변위를 억제하기 위해서 범퍼링(bumper ring) 또는 안내베어링(guide bearing)을 유연축의 적절한 위치에 설치할 필요가 있다. 비록 유연축계라 할지라도 정격속도와 가까운 4차 이상의 고차 위험속도를 정확히 규명하기 위해서는 모터의 동역학을 전체시스템에 결합하여야 함을 볼 수 있다. 해석은 유한요소법(finite element method)에 의해 수행된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.101-109
• /
• 1997

An analytical procedure on the base of the substructure synthesis and assumed modes method is developed to investigate the flexibility effect of bladed disk assembly on vibrational modes of flexible rotor system. In modeling the system, Coriolis forces, gyroscopic moments, and centrifugal stiffening effects are taken into account. The coupled vibrations between the shaft and bladed disk are then extensively investigated through the numerical simulation of simplified models, with varying the shaft rotational speed and the pretwist and stagger angles of the blade. It is found that the Coriolis and inertia forces and the inertia torque, which are induced by the one nodal diameter modes of the bladed disk and vary depending upon the stagger and pretwist angles, lead to the coupled motions of the shaft and the bladed disk.

• Journal of Power Electronics
• /
• 제17권4호
• /
• pp.953-962
• /
• 2017

Momentum flywheels are widely applied for the generation of small and precise torque for the attitude control and inertial stabilization of satellites and space stations. Due to its inherited system nonlinearity, the tracking performance of the flywheel torque/speed in dynamic/plug braking operations is limited when a conventional controller is employed. To take advantage of the well-separated two-time-scale quantities of a flywheel driving system, the singular perturbation technique is adopted to improve the torque tracking performance. In addition, the composite control law, which combines slow- and fast- dynamic portions, is derived for flywheel driving systems. Furthermore, a novel control strategy for plug braking dynamics, which considers couplings between the Buck converter and the three-phase inverter load, is designed with easy implementation. Finally, experimental results are presented to demonstrate the correctness of the analysis and the superiority of the proposed methods.

• Structural Engineering and Mechanics
• /
• 제60권6호
• /
• pp.1079-1092
• /
• 2016

In this paper, an electromechanical integrated harmonic piezodrive system is proposed. The operating principle of the drive system is introduced. The equation of the relationship between the displacements of the flexible ring and the rotating angle of the rotor is deduced. Using the equation, the displacements of the flexible ring for the drive system and their changes along with the system parameters are investigated. The results show that the displacements of the flexible ring changes periodically along with the rotation of the vibrator; there are abrupt changes in the displacements of the flexible ring at some points where there are abrupt changes in the number of the mesh teeth pair; the length of the flexible ring, the excitation voltage, and the speed ratio have obvious effects on the displacements of the flexible ring. The results are useful for the design of the drive system. ;

• 전기학회논문지
• /
• 제68권1호
• /
• pp.36-43
• /
• 2019

In this paper, the characteristics of the coaxial magnetic gear according to the shape of the same gear ratio are analyzed using the two - dimensional finite element analysis. The rotor shape is SMCMG, CPCMG and RCMG. After this we analyzed the characteristics according to three shapes. Also, the amount of permanent magnet used in each shape was compared. Next, characteristics analysis of the magnetic gear according to the shape at the same torque was performed. And the total weight and efficiency of the magnetic gears were compared and verified.

• 풍력에너지저널
• /
• 제4권2호
• /
• pp.17-24
• /
• 2013

Idealized PID-controlled rotor-speed error for blade pitch control of wind turbines responds as a second-order system with natural frequency and damping ratio for closed-loop system. RISO National Laboratory has recommended specific natural frequency(=0.6 rad/s) and damping ratio(=0.7) for 2 MW wind turbine. The baseline controller for 5 MW wind turbine of NREL(National Renewable Energy Laboratory) is designed based on the same values of RISO recommendation. This study investigates the effect of the natural frequency and damping ratio of the controller for NREL 5 MW wind turbine. It is confirmed that RISO recommendation shall be tuned for each wind turbine.

• 대한기계학회논문집B
• /
• 제32권7호
• /
• pp.549-557
• /
• 2008

Despite of the laminar-turbulent transition region co-exist with fully turbulence region around the leading edge of an airfoil, still lots of researchers apply to fully turbulence models to predict aerodynamic characteristics. It is well known that fully turbulent model such as standard k-model couldn't predict the complex stall and the separation behavior on an airfoil accurately, it usually leads to over prediction of the aerodynamic characteristics such as lift and drag forces. So, we apply correlation based transition model to predict aerodynamic performance of the NREL (National Renewable Energy Laboratory) Phase IV wind turbine. And also, compare the computed results from transition model with experimental measurement and fully turbulence results. Results are presented for a range of wind speed, for a NREL Phase IV wind turbine rotor. Low speed shaft torque, power, root bending moment, aerodynamic coefficients of 2D airfoil and several flow field figures results included in this study. As a result, the low speed shaft torque predicted by transitional turbulence model is very good agree with the experimental measurement in whole operating conditions but fully turbulent model(${\kappa}-\;{\varepsilon}$) over predict the shaft torque after 7m/s. Root bending moment is also good agreement between the prediction and experiments for most of the operating conditions, especially with the transition model.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.799-806
• /
• 2007

One method for improving the torque capacity of the CVT is to use a split-powered CVT(SPCVT) to reduce the power transmitted into a continuously variable unit(CVU). A variable bridge SPCVT with two planetary gear units(PGUs), which are composed of a sun gear, a ring gear, and carrier and planetary gears, can minimize the power to the CVU. However, a SPCVT with a conventional CVT should possess a dual mode, which would allow the conventional CVT to be used at high speeds and an additional gear train to be used at low speeds. The inner-spherical CVU(ISCVU) with an inner and outer spherical contact mechanism developed in this study can cover the range from low to high speeds. The rated power and the overall speed ratios were 100 kW and $0.09{\sim}0.36$, respectively. Power efficiency was numerically calculated to be over 90% over the speed ratio range of $0.1{\sim}0.29$. The maximum shear stress at the two contact areas of the rotor pairs, the minimum life and the overall size were estimated to be 700 MPa, 276 kh and $350{\times}350{\times}400mm^3$, respectively. This study shows that an ISCVU and a variable bridge type PGU can realize the SPCVT with a single mode for a vehicle.

• 한국산학기술학회논문지
• /
• 제18권1호
• /
• pp.238-244
• /
• 2017

공작기계 응용에 있어서 고속 및 고효율 가공의 추세는 스핀들의 고속화를 지속적으로 요구하고 있다. 내장형 모터를 장착한 스핀들은 가공시스템의 구조를 단순하게 한다. 하지만 로터에는 불평형 질량에 의해 진동이 발생하며, 이를 제거하기 위한 밸런싱 작업은 필수적이다. 이 논문에서는 내장형 모터를 장착한 고속 스핀들의 동적거동을 해석하였다. 불평형 질량, 베어링 강성, 회전 속도의 변화에 따른 휘돌림 궤적을 해석하였고, 이를 저감시키는 방법을 모색하였다. 또한 Timoshenko 빔 요소를 적용하여 스핀들-베어링 시스템을 모델링하고, 영향 계수법을 적용하여 밸런싱 과정을 시뮬레이션 하였다. 스핀들의 경우, 불평형 하중이 작용할 때, 베어링 지지점에서 가장 작은 휘돌림 궤적이 나타났으며, 양단에서 가장 큰 휘돌림 궤적을 나타내었다. 스핀들의 회전속도가 증가함에 따라 스핀들 선단에서의 휘돌림 궤적도 증가하였다. 베어링의 강성이 커짐에 따라 휘돌림 궤적 또한 증가하였다. 밸런싱 전, 후의 휘돌림 궤적 반경은 최대 73%까지 감소함을 확인할 수 있었다. 이러한 연구 결과는 CNC 자동선반의 스핀들 고속화에 중요한 정보를 제공하고 있다.