• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1120-1123
• /
• 2003

This paper is proposed a ANN-based rotor position and speed estimation method for IPMSM by measuring the currents. Because the proposed estimator treats the estimated motor speed as the weights, it is possible to estimate motor speed to adapt back propagation algorithm with 2 layered neural network. The proposed control algorithm is applied to IPMSM drive system. The operating characteristics controlled by neural networks control are examined in detail.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.407-408
• /
• 2012

본 논문은 매입형 영구자석 동기 전동기의 감자 상황에서의 초기 위치 추정 방법을 제시한다. 신호 주입 센서리스 제어시, 영구자석의 극성을 추정하기 위해 영구자석의 자속에 의한 자기 포화 현상을 이용한다. 그러나 영구자석에 감자가 발생하였을 때는 극성에 따른 포화의 특성이 정상적인 경우와 달라져 전압을 주입했을 때 영구자석의 극성을 잘못 판단하게 될 수 있다. 본 논문에서는 감자 상황에서도 바른 극성 검출을 위해 d축 전류를 변경시켜가면서 전압을 주입하여 영구자석의 극성을 추정한다. 이를 통해 영구자석의 감자 상태를 파악하고, 감자 상황에서도 초기 위치 추정이 가능하게 된다. 정상적인 매입형 영구자석 동기전동기와 동일한 사양의 감자된 회전자를 가진 전동기에 제안된 초기 위치 추정 방법을 적용되어 그 타당성을 실험적으로 입증하였다.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.337-338
• /
• 2015

본 논문에서는 고주파 신호 주입 센서리스 제어를 위한 정지 좌표계 상의 회전자 위치를 추정하는 새로운 기법에 대하여 제안한다. 기존 방법은 저역 통과 필터의 시지연 및 전류 차로 이루어진 행렬의 역행렬 유무 문제가 존재하였다. 제안된 기법은 이러한 문제의 해결방안으로 정지 좌표계 상에서 변환 행렬을 이용하여 회전자 위치 정보를 추출해 낸다. 또한 추출해 낸 위치 정보로 전대역 통과 필터를 이용하여 회전자 위치를 정밀하게 추정하게 된다. 시뮬레이션을 통하여 제안된 방법의 타당성을 검증하였다.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1614-1622
• /
• 2014

A novel equivalent flux sliding-mode observer (SMO) is proposed for dual three-phase interior permanent magnet synchronous motor (DT-IPMSM) drive system in this paper. The DT-IPMSM has two sets of Y-connected stator three-phase windings spatially shifted by 30 electrical degrees. In this method, the sensorless drive system employs a flux SMO with soft phase-locked loop method for rotor speed and position estimation, not only are low-pass filter and phase compensation module eliminated, but also estimation accuracy is improved. Meanwhile, to get the regulator parameters of current control, the inner current loop is realized using a decoupling and diagonal internal model control algorithm. Experiment results of 2MW-level DT-IPMSM drives system show that the proposed method has good dynamic and static performances.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.104-111
• /
• 2018

The sensorless control of high efficiency air compressors using a permanent magnet type synchronous motor as an oil-free air compressor is quite common. However, due to the nature of the air compressor, it is difficult to install a position sensor. In order to control the permanent magnet type synchronous motor at variable speed, the inclusion of a position sensor to grasp the position of the rotor is essential. Therefore, in order to achieve sensorless control, it is essential to use a permanent magnet type synchronous motor in the compressor. The position estimation method based on the back electromotive force, which is widely used as the sensorless control method, has a limitation in that position errors occur due either to the phase delay caused by the use of a stationary coordinate system or to the estimated back electromotive force in the transient state caused by the use of a synchronous coordinate system. Therefore, in this paper, we propose a method of estimating the position and velocity using a rotation angle tracking observer and reducing the speed ripple through a disturbance observer. An experimental apparatus was constructed using Freescale's MPU and the feasibility of the proposed algorithm was examined. It was confirmed that even if a position error occurs at a certain point in time, the position correction value converges to the actual vector position when the position error value is found.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.2
• /
• pp.121-127
• /
• 2017

From the perspective of commercializing rotating machines equipped with magnetic bearings, maintaining the error between the mechanical center and the magnetic center within an acceptable level is crucial. The existing method of measuring the center error is to adjust the position references that minimize the current imbalance present in levitation control outputs. However, this method can be applied only after all the components of the system are operational. In this paper, we present a new method of estimating the center error by using only the position sensors and a current source. A force model that relates the position of the rotor with the coil currents is set up. Using this model, the center error is estimated by minimizing the difference between the force angles and the contact angles measured in a pull test. The feasibility of the method is numerically and experimentally validated.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.5
• /
• pp.427-436
• /
• 2002

This paper presents an implementation of high-dynamic performance of position sensorless motion control system of Reluctance Synchronous Motor(RSM) drives for an industrial servo system with direct torque control(DTC). The problems of high-dynamic performance and maximum efficiency RSM drives controlled by DTC are saturation of stator linkage flux and nonlinear inductance characteristics with various load currents. The accurate estimation of the stator flux and torque are obtained using stator flux observer of which a saturated inductance $L_d$ and $L_q$ can be compensated by adapting from measurable the modulus of the stator current and rotor position. To obtain fast torque response and maximum torque/current with varying load current, the reference command flux is ensured by imposing $I_{ds} = I_{qs}$. This control strategy is proposed to achieve fast response and optimal efficiency for RSM drive. In order to prove rightness of the suggested control algorithm, the actual experiment carried out at $\pm$20 and $\pm$1500 rpm. The developed digitally high-performance motion control system shown good response characteristic of control results and high performance features using 1.0kW RSM which has 2.57 Ld/Lq salient ratio.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.240-243
• /
• 2003

Sensorless Vector control of the permanent magnet synchronous motor(PMSM) typically requires knowledge of the PMSM structure and parameters, which in some situations are not readily available or may be difficult to obtain. In this paper, by measuring the currents of the PMSM drive, a neural-network-based rotor position and speed estimation method for PMSM is described. Because the proposed estimator treats the estimated motor speed as the weights, it is possible to estimate motor speed to adapt back propagation algorithm with 2 layered neural network. The proposed control algorithm is applied to PMSM drive system. The operating characteristics controlled by neural networks control are examined in detail.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.302-304
• /
• 1996

In this paper, a new algorithm for sensorless speed control of switched reluctance motor (SRM) is proposed. It is based on the measurement of initial rate of change of phase current. The initial rate of rise of phase current mainly depends up on the phase inductance at the time instant when the phase is excited. Therefore, the measurement of initial di/dt permits rotor position estimation, which is used to trigger the next phase. In the proposed technique, there is no need to generate additional current pulses when a phase is not excited. Therefore, this scheme does not introduce the unwanted braking torque. Also, only one current measurement is made every time a phase is excited. This reduces the computational load on the micro-controller and enhances the speed range of the sensorless drive. By using this scheme it is possible to implement the sensorless control of SRM using low cost micro-controller.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.143-148
• /
• 2020

In the case of a system that detects and controls the phase of an alternating voltage, the analog control method compensates the phase offset part by filtering for the detected phase and applies it to the control. However, in the digital control method, precise control cannot be achieved due to an error between the operating frequency of the microprocessor or the microcontroller and the input phase time when controlled using such phase detection. In general, when the method used is a certain time, the accumulated error is compensated and adjusted at random. To solve this problem, a method of detecting a zero point in real time and compensating for the operating frequency of the microprocessor is needed. Therefore, the research to be performed in this paper to reduce these errors and apply them to precise digital control is as follows. 1) Research on how to implement Zero Crossing Detection algorithm through simulation modeling to compensate the zero point to match the operating frequency through detection. 2) A study on the method of detecting zero points in real time through the Zero Crossing Detection design using a microcontroller and compensating for the operating frequency of the microprocessor. 3) A study on the estimation of the rotor position of BLDC motors using the Zero Crossing Detection circuit.