• 한국산업융합학회 논문집
• /
• 제26권6_1호
• /
• pp.993-999
• /
• 2023

In this paper, a novel polishing tool mechanism with 3-axis compliance is presented, which consists of 2-axis rotational and 1-axis linear compliances in series. The 2-axis rotational compliance mechanism is made up of four cantilever beams for adjusting rotational stiffness and one flexure universal joint at the center for constraining the z-axis deflection. The 2-axis rotational compliance can mechanically adjust the polishing tool to machined surfaces. The polishing press force can be simply controlled by using a linear spring along the z-axis. The 2-axis rotational and 1-axis linear compliance design is decoupled. The stiffness analysis of the 2-axis compliance mechanism was performed based on link compliance matrix and rigid body transformation. A 3-axis polishing tool was designed by configuring the 2-axis compliance mechanism and one linear spring.

• 소성∙가공
• /
• 제18권2호
• /
• pp.172-176
• /
• 2009

In this paper, new aspherical surface polishing mechanism is suggested to polish aspherical glass lens mold by both airbag polishing tool and reverse-rotational eccentric motion. Up to now, conventional aspherical lens polishing method by the small tool polishing uses the aspherical surface profile and the trajectory of the polishing tool is also controlled. However, full contact concept by airbag polishing tool and no position control make the easy polishing setup and does not need aspherical design profile. An aspherical lens polishing machine was made for this study and a tool mark removal experiment fur the fine-grounded lens mold was successfully performed.

• 한국생산제조학회지
• /
• 제21권5호
• /
• pp.714-719
• /
• 2012

In this paper, the polishing force monitoring and the control method were implemented for the polishing machine with the airbag tool. Airbag tool has been known to be adaptable to the curvature variation such as the aspherical and the free-form surface. However, it was necessary to control the tool movement of vertical axis also because of the table rotational wobble and vibration. To solve it by the polishing force control, we installed another stepping motor to the z-axis. And the polishing force was measured with the load cell and controlled by the PID Labview controller. A few hundreds gram of the polishing force were well controlled under 0.8 second of the response time and 5% variation. An experiment was done to clean the edge burrs of the micro channel structure of width $87{\mu}m$ using the polishing force control.

• 한국공작기계학회논문집
• /
• 제11권1호
• /
• pp.38-44
• /
• 2002

In manufacturing die and mold, polishing: is important as it takes as much as 50% of the production cost. In this research, an attachable type polishing device to a WC machining center was developed. experiments were done with a special1y designed rotation type polishing device. Also an ultra-sonic (vibration type) waving device was introduced to acquire finer surface finishes. From the constructed data base based on the experimental results, it is shown that optimal polishing conditions are generated by the combined use of the rotation type tool and the vibration type tool.

• 한국정밀공학회지
• /
• 제30권12호
• /
• pp.1253-1258
• /
• 2013

Ceramic particles as polishing abrasives are often used in a magnetic abrasive polishing process because they have strong wear resistance. Non-ferromagnetic ceramic abrasives should be mixed with ferromagnetic iron particles for controlling the mixture within a magnetic brush during the polishing process. This study describes the application of the ceramic particles for the magnetic abrasive polishing. The distribution of the magnetic abrasives attached on a tool varies with magnetic flux density and tool rotational speed. From the correlation between abrasive adhesion ratio in the tool and surface roughness produced on a workpiece, practical polishing conditions can be determined. A step-over for polishing a large sized workpiece is able to be selected by a S curve, and an ultrasonic vibration assisted MAP produces a better surface roughness and increases a polishing efficiency.

• 한국공작기계학회논문집
• /
• 제18권1호
• /
• pp.22-28
• /
• 2009

In order to optimize the polishing process, Run to Run control scheme has been applied to the micro mold polishing in this study. Also, to fully understand the effect of parameters on the surface roughness a design of experiment is performed. By linear approximation of main factors such as gap and rotational speed of micro quill, EWMA (Exponential Weighted Moving Average) gradual mode controller is adopted as a optimizing tool. Consequently, the process converged quickly at a target value of surface roughness Ra 10nm and Rmax 50nm, and was hardly affected by unwanted process noises like initial surface quality and wear of magnetic abrasives.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.497-498
• /
• 2006

Tribological properties of a Magneto-Rheological(MR) fluid in a polishing process are studied. For this polishing process, abrasive wear model is proposed as a function of shear force, normal force and actual mean velocity of MR particles at workpiece surface. Experimental conditions are changed by varying the gap distance between workpiece and tool and the rotational speed of tool. From the experimental results, a modified Stribeck curve is obtained, and the friction coefficient turns out to have linear relationship with a modified Sommerfeld number. The validity of the wear model is supported by additional experiments performed for measuring material removal rates.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.326-331
• /
• 2000

This paper describes the statistical analysis techniques for the surface roughness assessment of polished surfaces. In experiments, the polishing process of the sample surfaces which are manufactured by ball end mill is consist of two steps; the cusp removal process and the surface finishing process. For the cusp removal process, the criterion of cusp removal was established from the power spectrum analysis to assess the change of the cusp removal rate. For the finishing process, the surface was polished by the rotational CBN tool and vibration wood tool. And the surface quality of polished surface was assessed using the functional parameters based on the statistical values of surface profiles. Consequently, the surface finish performance of the polished surface using the vibration wood tool was improved.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.617-623
• /
• 2004

This paper describes a dynamic thermal model for a representative dual axis rotational Chemical-Mechanical Polishing (CMP) tool. The model is one-dimensional but configured in the two-dimensional space and consists of three sub-models (pad, wafer and slurry fluid), with the first and the second that are time-dependent heat conduction-convection models with linear stationary (wafer) and nonlinear moving (pad) boundary conditions, and the last one that is a heat transport-convection model (slurry fluid). The modeling approach is validated by comparing the simulation results with available experimental data.

• 터널과지하공간
• /
• 제8권4호
• /
• pp.332-341
• /
• 1998

석판재의 모서리 가공작업은 많은 경우 자동화가 이루어지고 있지만 제품의 형태 가 복잡해지면 여전히 수작업에 의해 연마가 이루어지고 있다. 본 논문을 성형공구의 제작 에 앞서 성형공구의 특성과 장비의 운영요소들의 변화에 따른 연마절삭성능을 파악하기 위 한 기본시험이 수행결과를 나타내는 것이다. 장비의 운영요소는 헤드의 회전속도 및 이송속 도, 가압하중, 급수율, 절삭방향과 이송방향이 포함된다. 실험결과는 연마절삭성능 즉 공구 마모 무게에 대한 판재의 절삭량으로 표시하였고, 각 운영요소들 마다의 적정 운영수준이 제시되어 있다. 또한 연마재 투입략의 변화에 대한 마모시험에서는 마모도는 연마재의 증가 에 따라 증가하지만 어느 이상의 양에서는 오히려 감소하고 있다.