• Journal of the Korean Chemical Society
• /
• v.29 no.3
• /
• pp.205-212
• /
• 1985

By using the Mass-Weighted-Cartesian coordinate method, the allosteric effect of 2,2'-bipyridyl crown(4) ether is studied. The vibrational modes of 235, 234, 188, and 178cm$^{-1}$ belong to the pore opening motion of crown ether and those of 168, 104, and 67cm$^{-1}$ belong to the rotational vibration motion of bipyridyl. Especially the mode appearing at 178cm$^{-1}$ shows a large allosteric effect by activation of the allosteric site.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.3
• /
• pp.313-320
• /
• 1999

The Lane-Curvature Method(LCM) presented in this paper is a new local obstacle avoidance method for indoor mobile robots. The method combines Curvature-Velocith Method(CVM) with a new directional method called the Lane Method. The Lane Method divides the environment into lanes taking the information on obstacles and desired heading of the robot into account ; then it chooses the best lane to follow to optimize travel along a desired heading. A local heading is then calculated for entering and following the best lane, and CVM uses this heading to determine the optimal translational and rotational velocity space methods, LCM yields safe collision-free motion as well as smooth motion taking the dynamics of the robot Xavier, show the efficiency of the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.34-44
• /
• 2000

In this paper, a modified skyhook control for the semi-active Macpherson suspension system is investigated. A new model for the semi-active type suspension, which incorporates the rotational motion of the unsprung mass, is introduced and an output feedback control law using the skyhook control method is derived. The gains in the skyhook controller are adaptively adjusted by estimating the road conditions. Because two vertical acceleration sensors, one for the sprung mass and another for the unsprung mass, are used rather than using the angle sensor for the rotational motion of the control arm, the relative velocity of the rattle space is filtered using the acceleration signals. For testing the control performance, the actual damping force has been incorporated via the hardware-in-the-loop simulations. The performances of a passive damper and a semi-active damper are compared. Simulation results are provided.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.126-134
• /
• 1998

본 연구에서는 회전운동을 제어하기 위한 새로운 작동기로서 전기장에 대하여 매우 빠른 응답특성을 갖고 있는 두 쌍의 실린더형 ER(electro-rheological) 클러치/브레이크 작동기를 제안하였다. 자체조성 된 ER유체의 빙햄특성 모델을 실험적으로 도출하였으며, 이와 연계한 작동기 모델을 구성하여 전기장에 따른 전달 및 제동 토크를 해석한 후 알맞은 크기의 클러치/브레이크 작동기를 제작하였다. 제작된 작동기의 동적특성(시상수 등)을 작동기 모델에 고려하기 위하여 계단입력 전기장에 따른 과도응답 실험을 클러치와 브레이크 모드에서 각각 수행하였다. 제안된 작동기의 응용성을 보이기 위하여 두쌍의 작동기로 구동되는 실험실 차원의 소형 와권식 세탁기 시스템을 구성한 후 동적지배방정식을 유도하다. 각 작동기와 연계된 PID제어기를 설계하여 세탁과 탈수시의 회전운동을 제어하였으며, 부하질량의 변화에 대한 작동기 시스템의 제어 효율성과 장시간 운전을 통한 제어 내구성 실험을 수행하였다.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.444-451
• /
• 2005

The analysis of human arm motion during steering maneuver is carried out for investigation of man-machine interface of driver and steering system Each arm is modeled as interconnection of upper arm, lower arm, and hand by rotational joints that can properly represents permissible joint motion, and both arms are connected to a steering wheel through spring and damper at the contact points. The joint motion law during steering motion is determined through the measurement of each arm movement, and subsequent inverse kinematic analysis. Combining the joint motion law and inverse dynamic analysis, joint stiffness of arm is estimated. Arm dynamic analysis model for steering maneuver is setup, and is validated through the comparison with experimentally measured data, which shows relatively good agreement. To demonstrate the usefulness of the arm model, it is applied to study the effect of steering column angle on the steering motion.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.289-290
• /
• 2008

• International journal of advanced smart convergence
• /
• v.11 no.3
• /
• pp.206-214
• /
• 2022

Automobile manufacturers in each country are spurring the development of electric vehicles that use electric energy, an eco-friendly energy, as a futuristic vehicle. Electric vehicles have the advantage of no harmful gas or environmental pollution and low noise. Unlike automobiles using existing internal combustion engines using fossil fuels, electric vehicles use the electricity of batteries to cause rotational motion of motors. In the electric vehicle driven by the motor, it is indispensable to develop a controller for controlling the motor. One of the areas where automobile manufacturers are concentrating is the development of small electric vehicles as a personal transportation means. Small electric vehicles such as electric motorcycles, one-seat electric vehicles and two-seat electric vehicles are expanding the market as a means of operating throughout the city. In the domestic road conditions with many hills, it is effective to have a separate transmission system for small electric vehicles to drive smoothly. In this study, we propose a new type of continuously variable transmission(CVT) system to ensure that small electric vehicles can be driven smoothly in hilly domestic terrain. The proposed CVT system is equipped with a basic disk and a rotational disk in the driving pulley and the driven pulley, respectively, and is applied with a sloping spline to rotate the rotational disk. To commercialize the proposed CVT system, an experimental device was developed to examine the power transmission efficiency and the configuration of the CVT system was proposed.

• Coupled systems mechanics
• /
• v.12 no.1
• /
• pp.1-20
• /
• 2023

On the basis of the explicit time-domain method, an investigation is performed on the influence of the rotational stiffness and rotational damping of the vehicle body and front-rear bogies on the dynamic responses of the vehicle-bridge coupled systems. The equation of motion for the vehicle subsystem is derived employing rigid dynamical theories without considering the rotational stiffness and rotational damping of the vehicle body, as well as the front-rear bogies. The explicit expressions for the dynamic responses of the vehicle and bridge subsystems to contact forces are generated utilizing the explicit time-domain method. Due to the compact wheel-rail model, which reflects the compatibility requirement of the two subsystems, the explicit expression of the evolutionary statistical moment for the contact forces may be performed with relative ease. Then, the evolutionary statistical moments for the respective responses of the two subsystems can be determined. The numerical results indicate that the simplification of vehicle model has little effect on the responses of the bridge subsystem and the vehicle body, except for the responses of the rotational degrees of freedom for the vehicle subsystem, regardless of whether deterministic or random analyses are performed.

• KSTLE International Journal
• /
• v.2 no.2
• /
• pp.93-102
• /
• 2001

Ball bearings have been widely used for the spindle motor bearing in various kinds of information storage devices. Recently many researchers have been trying to replace ball bearings with fluid film bearings because of their superior NRRO(non-repeatable runout) characteristics. In this study, a numerical analysis has been conducted for the complicate bearing system composed of herringbone groove journal bearing and spiral groove thrust bearing for the spindle motor of the information storage device. At first, spindle motor bearing is modeled as journal bearing part and thrust bearing part separately, and then observed various influences of geometric parameters. Previous studies had considered only the translational motion of the journal bearing. However, this study takes the additional 2-degree of freedom rotation into consideration to attempt to describe the real motion of the spindle bearing. As a result, rotational stiffness coefficients and rotational damping coefficients are obtained. In addition, a spindle bearing system made up of four bearings is modeled and interpreted at once and coefficients of dynamic characteristics of each bearing are obtained. Finally, an eigen analysis of bearing system is made with these results. Through this analysis, it is possible to estimate an unstable condition of the system for given geometric parameters and to propose a method which is able to avoid the unstable condition by a proper adjustment of geometric parameters.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1958-1961
• /
• 2004

Ring Laser Gyroscopes used as navigational sensors inherently experience a lock-in region, where very low rotational rates are not measurable. Most RLG manufacturers use a mechanical dither motor that applies a small oscillatory rotational motion larger than this region to resolve this problem. Any input acceleration that bends this dithering axis causes flexure error, which is a noncommutative error that can not be compensated by simply using integrated gyro sensor output. This paper introduces noncommutative error equations that define attitude errors caused by flexure errors. In this paper, flexure error is classified as sensor level error if the sensing axis coincides with the dithering axis and as system level error if the two axes do not coincide. The relationship between gyro output and the rotation vector is introduced and is used to define the coordinate transformation matrix and angular motion. Equations are derived for both sensor level and system level flexure error analysis. These equations show that RLG based INS attitude error caused by flexure is directly proportional to time, amount of input acceleration and the dynamic frequency of the vehicle.