• Journal of Biosystems Engineering
• /
• 제23권5호
• /
• pp.427-438
• /
• 1998

In Korea, rotary implements are mainly utilized in the tillage operation. The attitude control system for rolling phenominon of tractors, which in caused due to uneven ground surfaces and sinkage of tractor wheels, is one of the most important control systems in agricultural tractors. The attitude control system of a rotary implement, attached on tractors, was designed and fabricated in this study. The control system was largely composed of four main units; a setting unit, a detection unit, a controller and a hydraulic unit. The implement was controlled by control signals from a computer proportional to controlled errors, on/off action of two directional solenoide valve and lift cylinder on the right lift rod. Response characteristic experiments for the control system fabricated in this study were carried out indoors and outdoors. The results of experiments showed the response characteristics sufficient to use as the attitude control system of rotary implements for agricultural tractors.

• Journal of Biosystems Engineering
• /
• 제24권4호
• /
• pp.293-300
• /
• 1999

The objectives of this study were to analyze the load acting on the transmission when tractor performed rotary operations in the poorly drained paddy fields and to compare its severeness with those obtained under different operational conditions. The loads were measured at the input shaft of the transmission and the load spectrum was constructed using the rain-flow cycle counting method. The severeness of the loads was represented by the partial damage sum which was determined by suing the modified Miner's rule. In the field with a shallow hardpan PTO speed affected severeness of the rotary operations greater than the forward speed did. In the field with deep hardpan, on the other hand, the effect of the forward speed was greater. the severeness in the well drained fields did not differ significantly from that in the field with a shallow hardpan. The severest load was recorded in the field with a deep hardpan.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1416-1421
• /
• 2007

In this paper, a novel MR brake with permanent magnet is developed. This system consists of rotary disk, permanent magnet, spring and MR fluid. Permanent magnets are attached to the rotary disk and moves in the direction of radius. The magnets are linked to rotor axis by spring. As rotation speed increases, the magnets move outward from the center of the system by centrifugal force in the MR fluid. A proper design of stator or case makes the system have unique torque characteristics. To show the performance of the system, the research is performed by following procedure. First, the electromagnetic characteristic of the system is analyzed using FEM and commercial code, Maxwell is used for this analysis. Then, torque is calculated using the result of the electromagnetic analysis to validate the performance of the system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.428-433
• /
• 2002

There have been many studies to visualize the vibration and noise of rotary compressor. Most of these studies assumed that the signal is stationary and the time-averaged signal is used for visualization. However, the noise and vibration signals generated during one cycle of crank shaft vary continuously. In this paper, the noise and vibration of rotary compressor which vary continuously are visualized by short time fourier transform method. The location of source and the transfer path of vibration and noise at arbitrary frequencies, which can not be visualized by averaged signal, can be visualized clearly.

• 한국연소학회지
• /
• 제12권3호
• /
• pp.24-32
• /
• 2007

A theoretical model was developed for rotary kiln and computational study was conducted to find the effect of feeding characteristics. One dimensional model with the variations of heating distribution, length of heating zone, excess air ratio and revolution was considered. The comparison of parallel-flow rotary kiln with that of counter-flow was conducted. For parallel-flow type, it is found that the variation of temperature of solid is not great for the zone that is following flame-heating zone. This zone is good to take the special treatment because thermal deviation is small and contacting time is enough for another treatment. Increase of excess air ratio have the effect of decreasing solid temperature. But this effect of decreasing solid temperature goes small for the great excess air ratio. The heating is efficient for the flame which has the maximum heating at the central region of the full length.

• 한국연소학회지
• /
• 제20권2호
• /
• pp.1-13
• /
• 2015

Drying, which is the oldest and most energy-intensive process, is an essential process for treatment of solid product. The specific procedure to design and evaluate the dryers, which are a rotary kiln dryer and a flash dryer, in case of drying the high-moisture coal was described. From determination of size to the heat and mass balance in one-dimensional model were conducted to evaluate the performance of dryers. Heat consumption, inlet gas temperature and size of the dryers were compared between a rotary kiln dryer and a flash dryer. Further considerations to evaluate the reactor elaborately were also discussed. Performance simulation of dryers along with the design procedure described here will provide helpful basis for understanding the concept of reactor design.

• 한국연소학회지
• /
• 제20권2호
• /
• pp.14-27
• /
• 2015

Calcination, which represents thermal decomposition of $CaCO_3$, is the key reaction in a cement process. Some reactions including heating-up also take place simultaneously in the calcination reactors. Basic thermal performance and dimensions of the reactors in two cases, which are a rotary kiln wih a four-stage cyclone pre-heater and a simple single rotary kiln, were compared. To employ the heat transfer, mass transfer and reaction rate as well as calcination, one-dimensional modeling was conducted in each case. Some simplification about the reactors was described, however, the reliable Nusselt number and heat transfer coefficients on the reactors were used to make results reliable.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.291-296
• /
• 1993

Taking a bledes axle of rotary tiller as a example, this paper discusses influences of four loading essential factors, which are strengthened amplitude, cycle times, loading sequence and loading frequency. in fatigue life. Determination principles of above four factors and monitoring methods of fatigue damage by local strain are dealt with. The actual field testing check of farm machinery is rapidly simulated by laboratory program fatigue test can shorten the period of development and improvement of a product. In the time of in-door simulation test, damage monitoring and four loading essential factors, which are strengthened amplitude , cycle times, loading sequence and loading frequency, have to be dealt with . If these problems are solved successfully, it is possible to accelerated test speed, reduce costs and manhours, and raise accuracy of test result. However strengthening method, loading pattern and influence of loading frequency on test result have not so far been discu sed systematically, damage monitoring is even more a difficult problem. Authors have studied above problems with the object of blades axle of rotary tiller.

• Structural Engineering and Mechanics
• /
• 제10권3호
• /
• pp.277-288
• /
• 2000

The present paper, deals with the dynamic analysis of a thin-walled tower with varying cross-section and additional masses. It, especially, deals with the effect of the rotary inertia of those masses, which have been neglected up to now. Using Galerkin's method, we can find the spectrum of the eigenfrequencies and, also, the shape functions. Finally, we can solve the equations of the problem of the forced vibrations, by using Carson-Laplace's transformation. Applying this method on a tall mast with 2 concentrated masses, we can examine the effect of the rotary inertia and the diaphragmatic operation of the above masses, on the 3 first eigenfrequencies.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제51권7호
• /
• pp.351-356
• /
• 2002

The oil circulation rate (OCR) of the rotary compressor is a crucial factor affecting the performance and reliability of air-conditioning systems. In this paper, topology optimization of the single-phase induction motor of rotary compressor is carried out for reducing the OCR. The nonlinear transient characteristic of single-phase induction motor for rotary compressor is analyzed by using FLUX2D. The topology optimization for electromagnetic systems is developed using the finite element method (FEM). The topology optimization is applied to a single-phase induction motor for reducing the OCR. For validation, optimize induction motors are manufactured and tested.