• Korea-Australia Rheology Journal
• /
• v.21 no.2
• /
• pp.127-133
• /
• 2009

Hemorheological results may be influenced by the time between blood sampling and measurement, and storage conditions (e.g., temperature, time) during sample delivery between laboratories may further affect the resulting data. This study examined possible hemorheological alterations subsequent to storage of rat and dog blood at room temperature ($22^{\circ}C$) or with cooling ($4{\sim}10^{\circ}C$) for 2, 4, 6, 24, 48 and 72 hours. Measured hemorheological parameters included hematological indices, RBC aggregation and RBC deformability. Our results indicate that marked changes of RBC deformability and of RBC aggregation in whole blood can occur during storage, especially for samples stored at room temperature. The patterns of deformability and aggregation changes at room temperature are complex and species specific, whereas those for storage at the lower temperature range are much less complicated. For room temperature storage, it thus seems logical to suggest measuring rat and dog cell deformability within 6 hours; aggregation should be measured immediately for rat blood or within 6 hours for dog blood. Storage at lower temperatures allows measuring EI up to 72 hours after sampling, while aggregation must be measured immediately, or if willing to accept a constant decrease, over 24~72 hours.

• Korean Journal of Materials Research
• /
• v.26 no.4
• /
• pp.187-193
• /
• 2016

Fabrication of iron oxide/carbon nanotube composite structures for detection of ammonia gas at room temperature is reported. The iron oxide/carbon nanotube composite structures are fabricated by in situ co-arc-discharge method using a graphite source with varying numbers of iron wires inserted. The composite structures reveal higher response signals at room temperature than at high temperatures. As the number of iron wires inserted increased, the volume of carbon nanotubes and iron nanoparticles produced increased. The oxidation condition of the composite structures varied the carbon nanotube/iron oxide ratio in the structure and, consequently, the resistance of the structures and, finally, the ammonia gas sensing performance. The highest sensor performance was realized with $500^{\circ}C/2h$ oxidation heat-treatment condition, in which most of the carbon nanotubes were removed from the composite and iron oxide played the main role of ammonia sensing. The response signal level was 62% at room temperature. We also found that UV irradiation enhances the sensing response with reduced recovery time.

• Korean Journal of Materials Research
• /
• v.26 no.12
• /
• pp.709-713
• /
• 2016

Grain morphology, phase stability and mechanical properties in binary Ti-Al alloys containing 43-52 mo1% Al have been investigated. Isothermal forging was used to control the grain sizes of these alloys in the range of 5 to $350{\mu}m$. Grain morphology and volume fraction of ${\alpha}_2$ phase were observed by optical metallography and scanning electron microscopy. Compressive properties were evaluated at room temperature, 1070 K, and 1270 K in an argon atmosphere. Work hardening is significant at room temperature, but it hardly took place at 1070 K and 1270 K because of dynamical recrystallization. The grain morphologies were determined as functions of aluminum content and processing conditions. The transus curve of ${\alpha}$ and ${\alpha}+{\gamma}$ shifted more to the aluminum-rich side than was the case in McCullough's phase diagram. Flow stress at room temperature depends strongly on the volume fraction of the ${\alpha}_2$ phase and the grain size, whereas flow stress at 1070 K is insensitive to the alloy composition or the grain size, and flow stress at 1270 K depends mainly on the grain size. The ${\alpha}_2$ phase in the alloys does not increase the proof stress at high temperatures. These observations indicate that improvement of both the proof stress at high temperature and the room temperature ductility should be achieved to obtain slightly Ti-rich TiAl base alloys.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.2 no.2
• /
• pp.105-133
• /
• 1969

The stability of three major pigments in lavers, namely chlorophylls, carotenoids, and phy-cobilins, during processing and storage was studied. The results of the pigment retention in fresh lavers during storage at low temperatures, of heat lability during heat treatment, and of the pigment loss during storage are summarized as follows: 1. The contents of chlorophyll a, xanthophyll (lutein+zeaxanthin), and carotene ($\alpha-+\beta-carotene$) averaged 1,525, 627, and $409{\mu}g/g$ of dry samples respectively The comparative composition of four carotenoids, lutein, $\beta-carotene$, zeaxanthin, and $\alpha-carotene$, was 35.9, 33.7, 12.2, and $5.8\%$ respectively. 2. In storage of fresh lavers at room ternperature ($20-25^{\circ}C$), 2 to $5^{\circ}C$, and $-15^{\circ}C$, the pigments generally were retained more at 2 to $5^{\circ}C$ than others while carotene only showed more retention at $-15^{\circ}C$ than at 2 to $5^{\circ}C$. Phycocyanin tended to decrease more rapidly than phyco-erythrin at low temperatures. 3. In regard to heat treatment of both dried and wet materials at 40, 60, 80, $100^{\circ}C$ respectively, the pigments were more stable at lower temperatures than at higher temperatures in both cases of materials. Carotenoids were retained more in wet materials than in the sun dried. Xanthophylls showed higher heat stability than carotenes. Phycoerythrin was considered more heat labile than phycocyanin, particularly at higher temperatures. 4. In storage of heat treated lavers for 50 days at room temperature, the retention of pigments appeared differently in accordance with the temperatures of treatment The materials treated at $60^{\circ}C$ showed better relention of pigments than those treated at the other temperatures. Degradation rate of xanthopllylls, carotenes, and phycobilins was decreased in the materials treated at higher temperatures, showing a tendency of great pigment retention even for a long period storage. Chlorophyll il was retained more in sun dried materials whereas xanthophyll and carotene were retained more in the wet. 5. In order to maintain a higher pigment stability during storage, the materials must be treated at $60^{\circ}C$ in a dryer with rapid ventilation until the moisture level reaches about $6.0\%$. In case of treatment at a higher temperature than $60^{\circ}C$, they must be treated for a short period of time to minimize pigment degradation by heat. 6. The lavers treated with the solutions of pH around 7.8 showed a higher retention of chlorophyll a. When treated with the solutions of algal extracts such as agar and alginic acid, uniform layer of laver sheets and better surface gloss of dried layers were obtained.

• Tribology and Lubricants
• /
• v.14 no.2
• /
• pp.57-62
• /
• 1998

When lubricants is used under severe running conditions, their tribological characteristics are very important. We have studied the lubricating oil viscosity, kinds of additives and their amounts, and lubricating oil temperatures were changed. In order to study the effect of oil temperature on the wear of the surface, the temperature of the oil was changed for the same sample. Moreover, the temperatures of three kinds of oils which have very different viscosities at room temperature, were varied between 6$0^{\circ}C$ and 115$^{\circ}C$ while the oil viscosity was unchanged. It was shown from the test results that surface wear is not greatly affected by the amount of ZnDTP (Zinc dialkyl dithio phosphate) antiwear agent, but EP (Extreme pressure) additives are less effective against wear than ZnDTP additives. The viscosity of lubricating oil and its temperature greatly affect the wear of the surface. Combining all the wear data with those of the surface strength, it was observed that the higher the load, the wider the scratching of wear, and also in the case of the same running load, the lower the wear, the longer the life of the surface strength.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.16 no.1
• /
• pp.92-99
• /
• 2020

High-temperature mechanical behaviors of Type 316L stainless steel (SS), which is considered as one of the major structural materials of Generation-IV nuclear reactors, were investigated through the tension and creep tests at elevated temperatures. The tension tests were performed under the strain rate of 6.67×10^-4 (1/s) from room temperature to 650℃, and the creep tests were conducted under different applied stresses at 550℃, 600℃, 650℃, and 700℃. The tensile behavior was investigated, and the modeling equations for tensile strengths and elongation were proposed as a function of temperature. The creep behavior was analyzed in terms of various creep equations: Norton's power law, modified Monkman-Grant relation, damage tolerance factor(λ), and Z-parameter, and the creep constants were proposed. In addition, the tested tensile and creep strengths were compared with those of RCC-MRx. Results showed that creep exponent value decreased from n=13.55 to n=7.58 with increasing temperature, λ = 6.3, and Z-parameter obeyed well a power-law form of Z=5.79E52(σ/E)^9.12. RCC-MRx showed lower creep strength and marginally different in creep strain rate, compared to the tested results. Same creep deformation was operative for dislocation movement regardless of the temperatures.

• KIEAE Journal
• /
• v.15 no.2
• /
• pp.37-43
• /
• 2015

Purpose: It is crucially important that indoor luminous conditions of built environments be carefully studied so as to promote comfort and occupants' well-being. Method: The current study therefore focuses on the lit aspect of an enclosed space considered to be a resting room ($4.5m{\times}6.32m{\times}2.5m$). Particularly, on the effect that light levels and light color temperatures have on the physiological and psychological responses of resting occupants. To do so, a questionnaire survey was carried out on 50 subjects. The independent variables for the experiment included 9 different luminous environment conditions setup using 3 different levels of illuminance (50 lx, 150 lx, 300 lx) and 3 different color temperatures (2000 K, 3800 K, 5600 K). A questionnaire was utilized in determining which conditions were preferred by occupants. Result: As it turns out, indoor luminous environment designed for relaxation purposes should display luminance levels of at least 150 lx and 3800 K of color temperature in order to provide a visually comfortable environment suitable for the occupant's relaxation while at the same time promoting the psychological and HRV well-being of resting occupants.

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.458-463
• /
• 1995

The optical and electrical properties of $C_{22}$-Quinolinium(TCNQ) Langmuir-Blodgett films have been studied depending on the annealing temperatures. The optimal properties were investigated using UV/visible(300-800[nm]) absorption spectra and FTIR(Fourier-transformed- infrared) absorption measurements. The electrical properties were investigated in a frequency range of 10[Hz]-13[MHz]. The UV/visible absorption spectra at room temperature show that there are four characteristic peaks at 320, 380, 494 and 678[nm]. These absorption peaks decrease very rapidly above the annealing temperature of 180[.deg. C], which is due to a structural change of TCNQ. The FTIR absorption measurements strongly support the result of the UV/visible absorption spectra, because the absorption peak of TCNQ- at 2181[$cm^{-1}$ /] also decreases above 140[.deg. C]. The frequency-dependent dielectric constant shows that there is a dielectric dispersion near 1[MHz] which is due to an orientational polarization of the molecules inside the film. The overall frequency-dependent dielectric constant is higher near 80[.deg. C]. It may be due to a softness of the alkyl chains.s.

• Nuclear Engineering and Technology
• /
• v.42 no.2
• /
• pp.193-202
• /
• 2010

In order to study the cladding properties of zirconium after a loss-of-coolant accident (LOCA)-simulation oxidation and water quenching test, commercial Zircaloy-4 and two kinds of HANA claddings were oxidized at temperatures ranging from $900^{\circ}C$ to $1250^{\circ}C$ and exposed for 300 s, and then cooled to $700^{\circ}C$ before quenching. Microstructural observations were made to evaluate the matrix characteristics with the chemical compositions after the LOCA-simulation test. Ring compression testing was then performed to compare the ductile behaviour of the HANA and Zircaloy-4 claddings. An X-ray diffraction (XRD) analysis was carried out for temperatures ranging from room temperature to $1250^{\circ}C$ for the oxide layer to verify the oxide crystal structure at each oxidation temperature.

• Advances in nano research
• /
• v.2 no.1
• /
• pp.23-56
• /
• 2014

The significant growth of the Si photovoltaic industry has been so far limited due to the high cost of the Si photovoltaic system. In this regard, the most expensive factors are the intrinsic cost of silicon material and the Si solar cell fabrication processes. Conventional Si solar cells have p-n junctions inside for an efficient extraction of light-generated charge carriers. However, the p-n junction is normally formed through very expensive processes requiring very high temperature (${\sim}1000^{\circ}C$). Therefore, several systems are currently under study to form heterojunctions at low temperatures. Among them, carbon nanotube (CNT)/Si hybrid solar cells are very promising, with power conversion efficiency up to 15%. In these cells, the p-type Si layer is replaced by a semitransparent CNT film deposited at room temperature on the n-doped Si wafer, thus giving rise to an overall reduction of the total Si thickness and to the fabrication of a device with cheaper methods at low temperatures. In particular, the CNT film coating the Si wafer acts as a conductive electrode for charge carrier collection and establishes a built-in voltage for separating photocarriers. Moreover, due to the CNT film optical semitransparency, most of the incoming light is absorbed in Si; thus the efficiency of the CNT/Si device is in principle comparable to that of a conventional Si one. In this paper an overview of several factors at the basis of this device operation and of the suggested improvements to its architecture is given. In addition, still open physical/technological issues are also addressed.