• 한국구조물진단유지관리공학회 논문집
• /
• 제18권5호
• /
• pp.1-8
• /
• 2014

본 연구에서는 유황을 폴리머화하여 내화학성능이 요구되는 구조물의 콘크리트 표면보호재로 활용할 수 있도록 성능을 검토하였다. 평가 결과, 유황폴리머 표면도포재의 중력식 스프레이가 적절한 것으로 나타났으며, 도포횟수는 왕복 3회 이상 도포했을 때 1MPa 이상의 부착강도 확보가 가능하였다. 표면보호재가 도포될 콘크리트 표면조건은 상온조건 ($20{\sim}30^{\circ}C$) 이상에서 높은 부착강도를 나타내었으며, 온도가 높을수록 부착강도가 증가하였다. 표면보호재의 채움재 혼입량에 따른 강도특성 평가결과, 20~40% 정도 혼입된 채움재는 유황폴리머의 수축을 저감시키는 효과를 나타내어 강도 향상에 기여하였다. 또한, 플라이애시 보다는 규사 혼입시 부착강도가 높았고, 동시 혼입시 가장 우수한 부착강도 특성을 나타내었다. 화학저항성은 플라이애시 및 규사를 각각 20% 대체한 배합에서 부착강도 저하가 최소로 되어 우수한 내화학성을 나타내었다. 염소이온 침투에 대한 성능평가를 수행한 결과, 표면보호재를 도포하지 않은 시험체에 비하여 유황폴리머 표면보호재를 도포한 경우, 29~48% 정도 염소이온침투저항성이 증대되었다. 표면보호재의 도포조건, 압축강도, 부착강도, 화학저항성, 염해저항성 등을 모두 고려하여 볼 때, 본 연구범위에서는 유황폴리머에 채움재로서 규사와 플라이애시를 각각 20%씩 대체하는 것이 적절한 수준인 것으로 판단된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.344-344
• /
• 2014

Transparent amorphous oxide semiconductors such as a In-Ga-Zn-O (a-IGZO) have advantages for large area electronic devices; e.g., uniform deposition at a large area, optical transparency, a smooth surface, and large electron mobility >10 cm2/Vs, which is more than an order of magnitude larger than that of hydrogen amorphous silicon (a-Si;H).1) Thin film transistors (TFTs) that employ amorphous oxide semiconductors such as ZnO, In-Ga-Zn-O, or Hf-In-Zn-O (HIZO) are currently subject of intensive study owing to their high potential for application in flat panel displays. The device fabrication process involves a series of thin film deposition and photolithographic patterning steps. In order to minimize contamination, the substrates usually undergo a cleaning procedure using deionized water, before and after the growth of thin films by sputtering methods. The devices structure were fabricated top-contact gate TFTs using the a-IGZO films on the plastic substrates. The channel width and length were 80 and 20 um, respectively. The source and drain electrode regions were defined by photolithography and wet etching process. The electrodes consisting of Ti(15 nm)/Al(120 nm)/Ti(15nm) trilayers were deposited by direct current sputtering. The 30 nm thickness active IGZO layer deposited by rf magnetron sputtering at room temperature. The deposition condition is as follows: a rf power 200 W, a pressure of 5 mtorr, 10% of oxygen [O2/(O2+Ar)=0.1], and room temperature. A 9-nm-thick Al2O3 layer was formed as a first, third gate insulator by ALD deposition. A 290-nm-thick SS6908 organic dielectrics formed as second gate insulator by spin-coating. The schematic structure of the IGZO TFT is top gate contact geometry device structure for typical TFTs fabricated in this study. Drain current (IDS) versus drain-source voltage (VDS) output characteristics curve of a IGZO TFTs fabricated using the 3-layer gate insulator on a plastic substrate and log(IDS)-gate voltage (VG) characteristics for typical IGZO TFTs. The TFTs device has a channel width (W) of $80{\mu}m$ and a channel length (L) of $20{\mu}m$. The IDS-VDS curves showed well-defined transistor characteristics with saturation effects at VG>-10 V and VDS>-20 V for the inkjet printing IGZO device. The carrier charge mobility was determined to be 15.18 cm^2 V-1s-1 with FET threshold voltage of -3 V and on/off current ratio 10^9.

• Korean Chemical Engineering Research
• /
• 제51권6호
• /
• pp.666-670
• /
• 2013

실리콘계 태양전지 제조과정에서 발생하는 불량품에서 실리콘웨이퍼를 회수하는 연구를 수행하였다. 상온($25^{\circ}C$)에서 인산용액 농도, 산성불화암모늄 농도, 킬레이트제 종류 및 농도를 변화시키면서 폐태양전지의 반사방지막 및 N층의 제거 효율을 조사하였다. 10 wt% 인산, 2.0 wt% 산성불화암모늄, 1.5 wt% Hydantoin 사용 시 제거 효율이 가장 우수 하였다. 인산농도가 증가할수록 미세입자의 표면전위가 (+)로 변하여 정전기적 인력에 의해 실리콘웨이퍼 표면에 재흡착하여 표면처리 전보다 두께가 두꺼워졌으며, 표면의 오염도도 증가하였다. 인산-산성불화암모늄-킬레이트제 용액에 의한 표면처리방법은 모든 공정이 상온에서 수행되며, 공정이 단순하고, 폐수 발생량이 적고, 표면제거 효율이 우수한 방법으로 폐 태양전지의 재활용 및 기존 RCA 세정법의 대안으로 가능성이 매우 클 것으로 판단되었다.

• 한국진공학회지
• /
• 제13권1호
• /
• pp.39-45
• /
• 2004

UV-나노임프린팅 (Ultraviolet-Nanoimprinting Lithography:UV-NIL) 공정 기술은 수십 나노에서 수 나노미터 크기의 구조물을 적은 비용으로 대량생산 할 수 있다는 장점을 가지고 있는 기술로 최근 전세계적으로 연구가 활발히 진행되고 있다. 본 연구에서는 반도체 공정 중 마스크 제작 공정을 이용하여 나노패턴을 가진 5${\times}$5${\times}$0.09 인치 크기의 수정스탬프(quartz stamp)를 제작하였고, 임프린팅 (imprinting)시에 레지스트(resist)와 스탬프(stamp) 사이에서 발생하는 점착현상(adhesion)을 방지하고자 그 표면에 Fluoroalkanesilane(FAS) 표면처리를 하였다. 웨이퍼의 평탄도를 개선하고 친수(hydrophilic) 상태의 표면을 만들기 위해 그 표면에 평탄화층을 스핀코팅하였고, 1 nl의 분해능을 가진 디스펜서(dispenser)를 이용하여 레지스트 액적을 도포하였다. 스템프 상의 패턴과 레지스트에 임프린트된 패턴은 SEM, AFM 등을 이용하여 측정하였으며, EVG620-NIL 장비를 이용한 임프린팅 실험에서 370 nm - 1 um 크기의 다양한 패턴을 가진 스탬프의 패턴들이 정확하게 레지스트에 전사됨을 확인하였다.

• 한국수소및신에너지학회논문집
• /
• 제21권4호
• /
• pp.271-277
• /
• 2010

$(Ba(Zr_{0.85}Y_{0.15})O_{3-\delta})$ oxide, showing high protonic conductivity at high temperatures and good chemical stability with $CO_2$ are referred to as hydrogen separation membrane. For high efficiency of hydrogen separation ($H_2$ flux and selectivity) and low fabrication cost, ultimate thin and dense BZY-Ni layer has to be coated on a porous substrate such as $ZrO_2$. Aerosol depostion (AD) process is a novel technique to grow ceramic film with high density and nano-crystal structure at room-temperature, and may be applicable to the fabrication process of AD integration ceramic layer effectively. XRD, SEM, X-ray mapping measurements were conducted in order to analyze the characteristics of BZY-Ni membrane fabricated by AD process. it is observed that it is homogeneous distribution for BZY-Ni. The result of $H_2$ permeation rate suggests that BZY-Ni composite is higher than BZY.

• 한국재료학회지
• /
• 제22권3호
• /
• pp.155-158
• /
• 2012

In this work, AlON-$Al_2O_3$ coatings were prepared on Al2021 alloy by the electrolytic plasma processing (EPP) method. The experimental electrolytes include: 2 g/l NaOH as the electrolytic conductive agent, 10 g/l $Na_2AlO_2$ as the alumina formative agent, and 0.5 g/l $NaNO_2$, $NaNO_3$, and $NH_4NO_3$ as the nitride inducing agents. The effects of different nitrogen inducing agents were studied by a combined compositional and structural analyses of the ceramic coatings carried out by Xray diffractometry (XRD) and scanning electron microscopy (SEM) for the specimens EPP-treated at room temperature for 15 min under a hybrid voltage of 260 DC along with an AC 50 Hz power supply (200 V). Microhardness tests and wear tests were carried out to correlate the evolution of the microstructure and the resulting mechanical properties. Potentiodynamic polarizations and immersion corrosion tests were carried out in 3.5wt% NaCl water solutions under static conditions in order to evaluate the corrosion behavior of the coated samples. The results demonstrate that $NaNO_2$ is proven to be a good nitrogen inducing agent to produce high quality AlON-$Al_2O_3$ ceramic coatings.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.24-27
• /
• 2009

Solid-state dye-sensitized solar cells (DSSCs) have been constructed employing supramolecular electrolytes with multiple hydrogen bonding. A supramolecule was facilely synthesized by one-pot reaction between the amines of methyl isocytosine (MIC) and the epoxy groups of poly(ethylene glycol diglycidyl ether) (PEGDGE) to produce quadruple hydrogen bonding units. Hydrogen bonding interactions and dissolution behavior of salt in supramolecular electrolytes are investigated. The ionic conductivity of the supramolecular electrolytes with ionic liquid, i.e. 1-methyl-3-propylimidazolium iodide (MPII) reaches $8.5{\times}10^{-5}$ S/cm at room temperature, which is higher than that with metal salt (KI). A worm-like morphology is observed in the FE-SEM micrographs of $TiO_2$ nanoporous layer, due to the connection of $TiO_2$ nanoparticles resulting from adequate coating by electrolytes. DSSCs employing the supramolecular electrolytes with MPII and KI exhibit an energy conversion efficiency of 2.5 % and 0.5 %, respectively, at 100 $mW/cm^2$, indicating the importance of the cation of salt. Solar cell performances were further improved up to 3.7 % upon introduction of poly(ethylene glycol dimethyl ether) (PEGDME) with 500 g/mol.

• 한국가축번식학회지
• /
• 제9권2호
• /
• pp.105-112
• /
• 1985

This research was carried out to investigate the optimal conditions ssociated with the RIA procedures such as a bridging phenomena, prozone effects and a new separation methods etc. The results obtained were summarized as follows: 1. The lgG fractions of donkey anti-rabbit IgG sera were purified by Protein-A-Sepharose affinity column, which indicates that Protein-A an affinity for IgG class of donkey antiserum. 2. In coating the IgG fraction on polystryene tubes, incubation conditions made no differences between 2 hr at room temperature and overnight at 4$^{\circ}C$. 3. There were no significant differences between 1st antibody-coated tube and 2nd antibody-coated tube as a separation method when compared in terms of reproducbility. A better reproducibility may be expected if the titers of 1st antibody for the progesterone to be assayed and of corresponding 2nd antibody are reasonably high. 4. The titers of anti-progesterone antibody for 3H-progesterone and progesterone-11HS-125I were 1:300 and 1:700 in liquid-phase, and 1:100 and 1:300 in solid-phse for the separation methods. 5. A bridging phenomena in which a standard curve is long and shallow were observed when progesterone-11HS-125I was used for the tracer, but not in 3H-progesterone. 6. A prozone effect in a solid-phase system, especially 1st antibody-coated tube method was observed which the degree of inhibition was significantly different although zero bindings look the same. In this case, the titration curve should be made both in the absence and in the presence of a, pp.opriate amount of competiter, standard, respectively.

• Journal of Pharmaceutical Investigation
• /
• 제23권3호spc1호
• /
• pp.9-18
• /
• 1993

Sugar spheres loaded with melatonin (MT) were coated with $Aquacoat^{\circledR}$ to control the release rate of MT over 8 hours. A zero-order release pattern over 8 hours was obtained with 20% coating on 8-10 mesh beads in USP basket dissolution studies. MT in 20% coated beads was quite stable at room temperature with less than 5% MT degraded during 6 months' storage. Dissolution profiles were also unchanged after 6 months. An oral preparation containing MT-loaded uncoated beads for immediate release and 20% coated beads with $Aquacoat^{\circledR}$ for controlled release over 8 hours was evaluated in six human subjects. When total 0.5 mg MT as low dose (immediate release portion of MT, 0.1 mg) was administered to four subjects, average peak plasma MT concentration was reached at about 600 pg/ml and maintained at about 10 pg/ml over 8 hours. Plasma MT concentration-time profiles were similar in shape to computer-simulated profiles. However, maximal plasma MT concentrations were three times greater compared to computer simulated curve. These results suggest that MT dose, ratio of immediate and controlled release MT, and pharmacokinetic parameters selected are adjusted to mimic endogenous MT concentration-time curve. In another study, 0.2 mg MT having 10% of immediate release portion and 80% controlled release portion produced plasma MT concentration-time curve which is more similar to endogenous profiles. A low bioavailability (<20%) may result from extensive first pass metabolism and remaining amounts of MT from controlled beads. A good correlation between plasma MT concentration and urinary excretion rate of 6-sulphatoxymelatonin (6-STMT), a major metabolite of MT was observed. As plasma MT concentration increased, urinary excretion rate of 6-STMT increased concomitantly. The linear relation between plasma MT and urinary excretion rate of 6-STMT was statistically significant. This result suggests that urinary 6-STMT may be used as an index of circadian rhythms of MT in humans.

• 한국응용과학기술학회지
• /
• 제23권1호
• /
• pp.77-84
• /
• 2006

Modified polyesters (TTBA-10C, -20C, -30C) that contain phosphorus and chlorine were synthesized by the condensation polymerization of tetramethylene bis(orthophosphate), neohexanediol trichlorobenzoate, 1,4-butanediol and adipic acid, in which tetramethylene bis(orthophosphate) and neohexanediol trichlorobenzoate were prepared previously in our laboratory. In this study, two-component flame-retardant polyurethane coatings (TTBA-10C/HDI-trimer=TTHD-10C, TTBA-20C/ HDI-trimer= TTHD-20C, TTBA-30C/HDI-trimer= TTHD-30C) were obtained by curing at room temperature with the synthesized TTBAs and hexamethylene diisocyanate (HDI)-trimer as a curing agent. The obtained TTHDs were made into coating samples and used as test samples for various physical properties. The physical properties of the flame-retardant coatings containing chlorine and phosphorus groups were generally inferior to those containing only phosphorus group. Flame retardancy was tested by vertical and horizontal combustion method, and $45_{\circ}$ Meckel burner method. Since the retardancy of flame-retardant coatings containing chlorine and phosphorus groups was better than that containing only phosphorus group, it could be concluded that the retardancy by the synergism effect of chlorine and phosphorus groups exhibited.