• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.487-493
• /
• 2020

Recently, the ministry of environment banned the use of the existing airless method using the spray in painting industrial facilities. Therefore, it is necessary to develop a pressure-roller attached to existing airless painting systems. The hole design of the SUS piping and drum-bases of pressure-rollers currently developed and sold have not been studied in detail, so their efficiency is questionable. In particular, if sufficient paint is not supplied to both ends of the roller, it is necessary to rework with a brush after painting. Therefore, the holes of the drum base need to be distributed so that the paint can flow to both ends of the roller. In this study, numerical analysis was performed to determine the effects of the hole design in the SUS piping and drum-base on the flow patterns of the paint and to suggest more efficient design measures. The analysis results showed that the uniform placement of the holes in the SUS piping is good for the balanced inflow of the paint. For the drum-base, the paint can flow better into both ends of the roller when the holes are concentrated and machined on both ends of the drum-base.

• Korean Journal of Applied Biomechanics
• /
• v.26 no.1
• /
• pp.11-20
• /
• 2016

Objective: This study aimed to compare biomechanical data between elite and beginner cyclists during cycle pedaling by performing a comparative analysis and to provide quantitative data for both pedaling performance enhancement and injury prevention. Methods: The subjects of this study included 5 elite cyclists (age: $18{\pm}0years$, body mass: $64.8{\pm}9.52kg$, height: $173.0{\pm}4.80cm$) and 5 amateur cyclists (age: $20{\pm}0years$, mass: $66.6{\pm}2.36kg$, height: $175.6{\pm}1.95cm$). The subjects pedaled on a stationary bicycle mounted on rollers of the same gear (front: 50 T and rear: 17 T = 2.94) and cadence of 90. The saddle height was adjusted to fit the body of each subject, and all the subjects wore shoes with cleats. In order to obtain kinematic data, 4 cameras (GR-HD1KR, JVC, Japan) were installed and set at 60 frames/sec. An electromyography (EMG) system (Telemyo 2400T, Noraxon, USA) was used to measure muscle activation. Eight sets of data from both the left and right lower extremities were obtained from 4 muscles (vastus medialis oblique [VMO], vastus lateralis oblique [VLO], and semitendinosus [Semitend], and lateral gastrocnemius [Gastro]) bilaterally by using a sampling frequency of 1,500 Hz. Five sets of events ($0^{\circ}$, $90^{\circ}$, $180^{\circ}$, $270^{\circ}$, and $360^{\circ}$) and 4 phases (P1, P2, P3, and P4) were set up for the data analysis. Imaging data were analyzed for kinematic factors by using the Kwon3D XP computer software (Visol, Korea). MyoResearch XP Master Edition (Noraxon) was used for filtering and processing EMG signals. Results: The angular velocity at $360^{\circ}$ from the feet was higher in the amateur cyclists, but accelerations at $90^{\circ}$ and $180^{\circ}$ were higher in the elite cyclists. The amateur cyclists had greater joint angles at $270^{\circ}$ from the ankle and wider knee joint distance at $0^{\circ}$, $180^{\circ}$, and $360^{\circ}$ than the elite cyclists. The EMG measurements showed significant differences between P2 and P4 from both the right VLO and Semitend. Conclusion: This study showed that lower body movements appeared to be different according to the level of cycle pedaling experience. This finding may be used to improve pedaling performance and prevent injuries among cyclists.

• Journal of Biosystems Engineering
• /
• v.8 no.1
• /
• pp.17-29
• /
• 1983

The milling process is considered as causing one of the greatest grain losses among all the processes in rice post-production. Major source of grain losses in the rice milling is considered as the whitening process. This study was attempted to develop an abrasive-type whitener, the whitening chamber of which being supplied by jet-air evenly and continuously. To investigate the milling performance by the new whitener, three kind of emery-stone grit(#36, #41, and #46), and three levels of rotational speed of emery stone roller (950, 1070, and 1200 rpm) were tested. The jet-air abrasive-type whitener was also compared with the conventional abrasive-type having no jet-air blower in terms of their milling performance. In addition, the effect of different combinations of sequential uses of the abrasive- and friction-type whiteners on the milling performance was also experimentally evaluated. The results of this study are summarized as follows; 1. In general, the whitening system combined with the abrasive type whitener with jet-air supply, which was newly designed, and the existing jet-air friction type whiteners produces more milled- and head-rice by about 0.3% points and 2.8% points, respectively than the system combined with the existing abrasive type without the jet-air supply under the same operational conditions. The former also consumed less electricity by 0.024 KwH per 100kg of milled rice production and gave more milling capacity by about 35 kg/hr. As compared with the conventional whitening system consisting of jet-air friction type whiteners only, the former yielded more milled- and head-rice by 1.5% points and 4.4% points, respectively. 2. The abrasive roller having 46 grit emery was better than the roller having 36 grit in aspects of milling performance and machine efficiency, in general. 3. With regard to the effect of combination method of abrasive type and friction type whiteners, one pass in abrasive type plus three passes in friction type gave better milling performance and energy efficiency than the two passes in abrasive type plus two passes in friction type regardless of the designs of the emery stone rollers. 4. The increase in rotational speed of the emery stone roller from 950 rpm to 1200 rpm presented negative effects on milled and head-rice yields and machine efficiency, but slightly positive effect on milling capacity.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.79-85
• /
• 2010

This paper presents a preliminary study of roller types for chip seals based on aggregate retention performance. Chip seal test sections composed of single seals of granite 78M aggregate and CRS-2 emulsion were constructed using three different roller types: the pneumatic tire roller, steel wheel roller, and combination roller. In order to investigate the performance of these rollers effectively, it is critical to test chip seal samples obtained directly from field construction. Therefore, test sections were constructed on New Sandy Hill Church Road near Bailey, North Carolina. Chip seal samples obtained from these sections were used for laboratory testing. The aggregate retention performance was evaluated using the flip-over test (FOT), Vialit test, and the third-scale Model Mobile Loading Simulator (MMLS3). Based on the test results and visual observation, both the pneumatic roller and the combination roller used together are recommended to improve chip seal performance with the sequence of the pneumatic roller rolling first followed by the combination roller.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.12-18
• /
• 2021

The purpose of this study is to effectively mitigate the bending displacement that occurs in the bridge due to forced vibration. We developed CTMD (Combine Tuned Mass Damper) that combines the relationship between spring and mass to control the bending behavior of simple beams. The experiment was conducted to confirm the control effect according to the change in the mass ratio of the developed CTMD. The developed CTMD is designed and manufactured so that the mass ratio can be adjusted according to the characteristics of the bridge. The maximum load of the spring applied to CTMD was fixed at 33.15 N. In order to evaluate the performance of the developed CTMD, a simple beam composed of hinges and rollers as boundary conditions was fabricated. In the experimental method, a CTMD was installed in the center of a simple beam and the deflection displacement according to the mass ratio was measured. The shaking condition was shaken at 3 Hz to induce the maximum bending behavior of the simple beam. As a result of the experiment, it was confirmed that when the optimal mass ratio was 2.1, the damping rate of the bending behavior displacement was about 71.2 %, indicating the best control effect.

• Journal of Aerospace System Engineering
• /
• v.16 no.6
• /
• pp.35-44
• /
• 2022

This study aims to evaluate the stress and life of cylindrical roller bearings used in aircraft gearboxes, and to select a roller profile that minimises the contact stress between bearing rollers and raceways. The mounting clearance of four points contact ball bearing was determined, so that cylindrical roller bearings support all radial loads, and the bearing mounting position was determined to maximise the bearing lives. In addition, the static safety factor and dynamic life of bearing were predicted according to ISO 76 & ISO/TS 16281 using the load spectrum determined based on the operating load cases of aircraft gearboxes. Furthermore, the optimal roller profile was selected by analysing the contact stress according to the roller profile shape, and the safety of each roller was evaluated. The results stated that the required safety factor and lifetime were satisfied, and Johns Gohar roller profile was optimal.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.25 no.2
• /
• pp.75-81
• /
• 1989

In this paper, the authors describe on the field experiment of the newly designed actual stow net, standing on the result of the model experiment to examine the performance of the conventional net and the newly designed net, presented in two previous reports of this series. Concurrently the additional experiment to find out the possibility of changing of operating system from the side to the stern was carried out. 1. Fundamental shape of the experimented net was 20 times aslarge asthe newly designed model net. Performance of the net was detected by using two ultrasonic echo sounders: one was set downward at the top-most spreader of the shearing device to detect the opening height of the device from the sea bed, and the other sidewise at the starboard top-most spreader to detect the top-most opening width of the devices. Opening height of the newly designed net showed about 3m smaller than the conventional net at slow current of 0.6m/sec and less but it overcome 1m at speedy current of 0.8m/sec and more. Opening width of the newly designed net was 1.4 times as large as that of the conventional net, ant the front projection area of the newly designed net mouth was estimated as 1.3~1.6 times as large as that of the conventional net. 2. The experiment on the stern operating system was tightly limited by the structure of the ship employed in the experiment, which was a stern trawler of 2275 GT. The ship confronted by the wind with main anchor, while the net was put over the stern slipway and the hauling line of shearing device was operated through the top rollers of gallows. The experiment was very suggestive in the view point to mechanize the operating system, and so to decrease the man power except the following question. The of bow-stern line of ship, and that of net is much different.