• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.218-221
• /
• 2004

This Research is to test the running stability of the developed bogie with 350km/h of which conventional speed is faster than Korea TGV 300Km/h. The running stability test has been executed in status of a car with the developed bogie on the roller rigger to adjust similar to the actual condition. And the test has been done in the two rail conditions, i.e. excitation and non-excitation, respectively. Running speed of bogie increased by the roller step by step. In consequence, the developed bogie in the non-excitation has run without any unstable point for 400kn0h. Vibration characteristics of carbody also was within the value specified on the UIC 518.

• 한국정밀공학회지
• /
• 제21권9호
• /
• pp.119-126
• /
• 2004

In this paper, we design a wedge type rail clamp which can protect container crane from a sudden strong blast with constant clamping force regardless of the operating period. When we design wedge type rail clamp, it is important to determine the angle of wedge and analyze a contact condition of roller and wedge so that we might develop a wedge type rail clamp for parking devices of port cargo working system with variable capacity. Therefore, this paper suggests a process to decide wedge angles within feasible range which could be obtained using load analysis and FEA of wedge type rail clamp

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 Asia Navigation Conference
• /
• pp.115-120
• /
• 2006

The rail clamp is the device to prevent the crane slips along rails from the wind blast as well as to locate a container crane in the set position in operating mode. In this study we conduct the research for the sliding distance of rail clamp and the proper position of supporter with respect to the wedge angle in the wedge type rail clamp. The sliding distance to display the clamping force of the jaw pad corresponding to the design wind speed criteria is determined by the total displacement of the rail clamp at the roller center and the wedge angle. And the supporter is the device to prevent the overload which is applied on each part of the rail clamp by wind speed increment, because a clamping force is generated by the sliding of the wedge due to the wind. Accordingly the position of the supporter to prevent the overload is determined by analyzing the forces applied to the rail clamp. In order to analyze the sliding distance and the proper position of supporter with respect to the wedge angle as the wind speed is 40m/s, 5-kinds of wedge angles, such as 2, 4, 6, 8, $10^{\circ}$, were adopted as the design parameter.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.71-76
• /
• 2008

This paper is concerned with the active vibration control of elevator by means of the active roller guide. To this end, a dynamic model for the horizontal vibration of the elevator consisting of a supporting frame, cage and active roller guides was derived using the energy method. Free vibration analysis was then carried out based on the equations of motion. Active vibration controller was designed based on the equations of motion using the LQR theory and applied to the numerical model. Rail irregularity and wind pressure variation were considered as external disturbance in the numerical simulations. The numerical results show that the active vibration control of elevator is possible.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(II)
• /
• pp.839-844
• /
• 2002

This research aims to test the running stability of the developed bogie with maximum operating speed of 350km/h, which of Korea TGV was 300km/h. The running stability test has been executed in status of a dummy car with one developed bogie and one dummy bogie on the roller rig to embody similar operation condition. The test has been done in the two rail conditions, i.e. excitation and non-excitation, respectively. Running speed has been increased by the roller step by step. In consequence, the developed bogie was proven to be able to run upto 400 Km/h without any unstable point in the non-excitation. Vibration characteristics of carbody also was within the value specified on the UIC 515.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.606-612
• /
• 2008

Creep force is one of the only appeared at conventional train which used to be driven by metallic wheel and rail contact. Due to the elastic deformation of wheel/rail contact patch by the weights of wheel and all the components related to it, creep force generates and becomes to the decision factor of critical speed of bogie(or railway vehicle) which is the criteria of avoiding vehicle to be unstable. There are many kind of factors which affect generation of creep force at a wheel/rail contact surface such as viscosity of contact patch, velocity, wheel and rail geometric profile, mechanical properties of wheel and rail. This paper concentrates on a wheelset simple 2 DOF Equation of Motion being exerted. From the simple numerical analysis using linear solution about getting creep force some factors could find roughly. Among the factors geometric parameter could be the one of most important for this study. In the future we'll prolong the range of study to find out method of measuring creep force easily.

• 한국기계가공학회지
• /
• 제6권3호
• /
• pp.58-64
• /
• 2007

The clamping force of a jaw pad is determined by the displacements of main part when two lockers are locked, after the clamping angle of a locker was set up in the wedge type rail clamp for a container crane. In this time, if the resistance of wedge frame generates due to several factors, the clamping angle of a locker to display the initial clamping force will be changed because of the reduction of displacement of extension bar. This resistance is determined by the eccentric distance between the roller and the wedge, and by the gap between the wedge frame and outer frame. In this study we measured the tensile force of both extension bar through the performance test of the prototype rail clamp in order to evaluate the effect of the resistance of wedge frame on the clamping force of the wedge type rail clamp.

• Tribology and Lubricants
• /
• 제33권1호
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• 동력기계공학회지
• /
• 제20권4호
• /
• pp.19-25
• /
• 2016

It is needed to use the gait training system for the rehabilitation of the disabled and old people. In this study, a gait training system of turn roller type is proposed for the purpose of helping the rehabilitation. A driving mechanism with the turn roller is designed by using the RecurDyn which is the dynamic analysis program. RecurDyn is used to analyze the dynamic behavior of the gait training system. The static load analysis is carried out to investigate the safety of this system. From the operating test of this system, it is noted that the driving error is little and the load capacity is 130 kgf.

• 대한기계학회논문집A
• /
• 제32권6호
• /
• pp.474-480
• /
• 2008

Recently, rods having irregular sections more complex than a rectangle or ellipse are necessary to produce mechanical parts. The cold shaped drawing process is used to obtain shaped drawn products with high levels of dimensional accuracy and quality. A cross roller guide, considered in this study, is one of the parts produced by shaped drawing process. A cross roller guide has a linear bearing system that rolls along a guide way. A cross roller guide is one of the most important components in terms of equipment because the quality of the product influences the precision linear motion. Therefore, the final dimensional accuracy of the linear rail in the shaped drawing is very important. The objective of this study is to find the optimized die angles to improve the dimensional accuracy and straightness of the final shaped drawn product. In order to achieve the aim of this study, design of experiment, FE-simulation, and the Taguchi method were used. Based on the analytical results, shaped drawing experiment has been performed to verify the result.