• 제목/요약/키워드: Roll-Rate

검색결과 304건 처리시간 0.026초

Development of Blue Light Cut Films Using a Roll-to-Roll Nano Micro Coating System

  • Hwang, Joong Kook;Shina, Hoon-Kyu;Chang, Sang-Mok
    • Transactions on Electrical and Electronic Materials
    • /
    • 제17권3호
    • /
    • pp.178-181
    • /
    • 2016
  • In this study a coating experiment was performed to fabricate blue light cut films, which represent a 390~430 nm cut off rate of more than 40% and a transmittance rate of more than 90%, using a roll-to-roll nano micro coating system. The study also analyzed the characteristics of the blue light cut films. Thus, the hardness, which is more than 3H, is ensured through fabricating films using a Sol-Gel process that will determine the proper hardness level. Also, the experiment shows excellent results by cutting blue light through a mixing blue light powder.

농산 부산물 수확방법에 관한 연구(I) -조제장치- (Development of Harvesting System for Agricultural By-Product(I) -Macerator-)

  • 김상헌;강화석;신범수;박청용
    • Journal of Biosystems Engineering
    • /
    • 제21권2호
    • /
    • pp.182-190
    • /
    • 1996
  • A macerating technique which can apply to the mechanical production system of the agricultural by-product was developed to increase the utilization of agricultural waste and solve the shortage problem in the forage supply for the livestock production. The macerating method is to shred the agricultural by-product by the two rolls which rotate at different speeds each other. The testing macerator was built and the optimum operating conditions are suggested. Results of this research are as follows: 1. The increase of the base roll speed and speed ratio between two rolls shows the better shredding index but decrease the drying rate. The optimum conditions of the base roll speed and the speed ratio between two rolls for the rice straw are 1200 rpm and 1.7-2.0 respectively. 2. The macerated alfalfa was dried to the 15%(w.b.) within 3 hrs in a field at speed ratio of rolls, 2:1 and base roll speed, 1800rpm. 3. The milled surface and straight knurled surface for the macerating roll have same effect on the drying rate of material. Both rolls have self-cleaning functions during operation.

  • PDF

세기변조방사선치료에서 Pitch와 Roll 변화에 따른 선량전달 정확성 평가 (Evaluation of dose delivery accuracy due to variation in pitch and roll)

  • 정창영;배선명;이동형;민순기;강태영;백금문
    • 대한방사선치료학회지
    • /
    • 제26권2호
    • /
    • pp.239-245
    • /
    • 2014
  • 목 적 : 세기변조방사선치료에서(Intensity modulated radiation therapy,IMRT) 6D robotic couch의 pitch 와 roll 변화에 따른 선량전달의 정확성을 평가하고자 한다. 대상 및 방법 : Trilogy(Varian Medical Systems, USA)와 6D robotic couch(ProturaTM 1.4, CIVCO, USA)를 사용하여 골반부위의 세기변조방사선치료를 진행한 14명의 환자를 대상으로 영상유도 시 발생한 pitch 와 roll 방향의 오차 값과 발생빈도를 분석하였다. 오차의 변화에 따른 선량전달 정확성의 차이를 평가하기 위해 pitch 와 roll의 변화가 $0^{\circ}$인 상태의 측정치를 기준으로 각각 $1.0^{\circ}$, $1.5^{\circ}$, $2.0^{\circ}$, $2.5^{\circ}$로 변화시킨 경우에 대하여 2차원 이온전리함 배열 검출기(I'mRT Matrixx, IBA Dosimetry,Germany)와 MultiCube Phantom(IBA Dosimetry, Germany)를 이용하여 측정 후 감마지수(3 mm, 3%)의 비교평가를 실시하였다. 실험에는 Dynamic Multi-Leaf Collimator의 sliding window기법을 사용한 3명의 자궁경부암 치료계획을 적용하였다. 결 과 : 대상 환자의 영상(3D/3D Match 78건, 2D/2D match 79건)을 분석한 결과 pitch 와 roll의 평균 오차값은 $0.9^{\circ}{\pm}0.7$, $0.5^{\circ}{\pm}0.6$, 최대 값은 $2.8^{\circ}$, $2.0^{\circ}$로 분석되었고, 최소값은 pitch 와 roll 모두 $0^{\circ}$으로 나타났다. 각각의 조건에서 측정된 선량전달에 대하여 감마지수를 이용하여 비교한 결과, pitch가 $1.0^{\circ}$, $1.5^{\circ}$, $2.0^{\circ}$, $2.5^{\circ}$일 때 gamma pass rate의 평균은 각각 97.75%, 96.65%, 94.38%, 90.91%, roll의 경우 $1.0^{\circ}$, $1.5^{\circ}$, $2.0^{\circ}$, $2.5^{\circ}$에서 평균 93.68%, 93.05%, 87.77%, 84.96%로 나타났고, pitch 와 roll을 동시에 변화시킨 경우 $1.0^{\circ}$, $1.5^{\circ}$, $2.0^{\circ}$에서 평균 94.90%, 92.37%, 87.88%의 결과 값을 얻었다. 결 론 : 대상 환자의 영상 유도 시 pitch 와 roll의 오차 발생률은 전체 치료 횟수에서 각각 82.20%, 72.20%로 분석되었고, 감마지수를 통해 오차 값이 커질수록 선량전달의 정확성이 낮아진다는 것을 확인할 수 있었다. 세기변조방사선치료 시 선량전달의 정확성을 높이기 위해서는 정확한 자세잡이와 더블어 적절한 영상유도를 통해서 pitch 와 roll 방향으로 발생할 수 있는 오차를 줄이도록 노력해야 할 것으로 사료된다.

바이올린 음원을 이용한 스펙트랄 롤오프 포인트의 최적점 검출 (Detection of the Optimum Spectral Roll-off Point using Violin as a Sound Source)

  • 김재천
    • 한국컴퓨터정보학회논문지
    • /
    • 제12권1호
    • /
    • pp.51-56
    • /
    • 2007
  • 음악을 분류하기 위해 특성함수를 사용하여 추출한 특성값 벡터를 사용한다. 본 실험에서는 특성값 벡터를 추출하기 위해 스펙트랄 롤오프, 분산, 평균 피크레벨을 사용하였다. 이중에서 스펙트랄 롤오프는 저음프레임과 고음프레임의 상대적인 비를 나타낸다. 최적의 롤오프 포인트를 찾기 위하여 롤오프 포인트를 0.05에서 0.9까지 0.05간격으로 증가시키며 반복실험 하였다. 롤오프 포인트를 증가시키며 분류성공률을 관찰하였다. 그리고 실험에 사용된 음원데이터는 바로크바이올린과 현대바이올린 연주이다. 두 종류의 악기는 모양과 주파수대역에 있어서 유사하지만 약간의 대역차와 질감의 차이를 가지고 있다. 이러한 특성이 최적의 롤오프 포인트를 찾는데 유용할 것으로 판단하였다. 실험결과 롤오프 포인트 0.85에서 가장 높은 분류성공률 85%를 나타냈다.

  • PDF

Linear Ion Beam Applications for Roll-to-Roll Metal Thin Film Coatings on PET Substrates

  • Lee, Seunghun;Kim, Do-Geun
    • Applied Science and Convergence Technology
    • /
    • 제24권5호
    • /
    • pp.162-166
    • /
    • 2015
  • Linear ion beams have been introduced for the ion beam treatments of flexible substrates in roll-to-roll web coating systems. Anode layer linear ion sources (300 mm width) were used to make the linear ion beams. Oxygen ion beams having an ion energy from 200 eV to 800 eV used for the adhesion improvement of Cu thin films on PET substrates. The Cu thin films deposited by a conventional magnetron sputtering on the oxygen ion beam treated PET substrates showed Class 5 adhesion defined by ASTM D3359-97 (tape test). Argon ion beams with 1~3 keV used for the ion beam sputtering deposition process, which aims to control the initial layer before the magnetron sputtering deposition. When the discharge power of the linear ion source is 1.2 kW, static deposition rate of Cu and Ni were 7.4 and $3.5{\AA}/sec$, respectively.

신경망 함수를 이용한 자동차강의 변형저항 개발 및 압연하중 예측 (Development of Flow Stress equation of High strength steel for automobile using Neural Network and Precision Roll Force Model)

  • 곽우진
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
    • /
    • pp.145-152
    • /
    • 2004
  • The flow stress value was calculated by comparing predicted and measured roll force. Using basic on-line roll force model and logged mill data the flow stress equation of high strength steel for automobile was derived. The flow stress equation consists of the flow stress equation of carbon steel and flow stress factor calculated by neural network with input parameters not only carbon contents, strip temperature, strain, and strain rate, but also compositions such as Mn, p, Ti, Nb, and Mo. Using the flow stress equation and basic roll force model, precision roll force model of high strength steel for automobile was derived. Using test set of logged mill data the flow stress equation was verified.

  • PDF

회전체의 GPS 신호 영향 분석 (Analysis of Effect of the Spinning Vehicle on the GPS Signal)

  • 조종철;김정원;황동환;이상정
    • 대한전기학회:학술대회논문집
    • /
    • 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
    • /
    • pp.189-191
    • /
    • 2006
  • This paper analyzes effect of the spinning vehicle on the GPS signal. In rapid spinning vehicles such as missiles and space rockets, carrier phase and frequency depend on the roll rate of the vehicle. It induces phase and frequency modulation caused by the roll rate. The modulated phase and frequency increase dynamic stress error of the tracking loop. Even though higher order tracking loop can remove dynamic stress error, the dynamic stress error can not be remove in this case. In order to analyze the effect of the spinning vehicle on the GPS signal, the experiments are carried out. The experiment results show the modulation of the carrier frequency and phase caused by the roll rate of the spinning vehicle.

  • PDF

길이방향을 따라 선형 대칭적으로 변하는 좌우대칭 U형 단면을 가진 제품의 포밍 롤 설계 (Design of Forming Rolls for Parts with a Symmetric U-type Cross-section that Varies Linearly and Symmetrically in the Longitudinal Direction)

  • 김광희;윤문철
    • 한국기계가공학회지
    • /
    • 제15권4호
    • /
    • pp.73-82
    • /
    • 2016
  • Recently, automobile industries have been developing many structural automotive parts made of thin, high-strength steel strips to produce safer and more environmentally friendly cars. The roll forming process has been considered one of the most efficient processes in manufacturing high-strength steel parts because it is a high-speed process that forms sheets in increments. However, most automotive parts vary longitudinally in their cross-sections. Therefore, it is difficult to apply the roll forming process to automotive parts made of high-strength steel. A variable section roll forming process has been proposed in recent studies. The rotational axes of the forming rolls are fixed, and the forming rolls have three-dimensional shape. As such, the cross-section of the part varies linearly along its length, and the angle between the bend line and longitudinal axis is less than 1 degree. Thus, the rate of cross-sectional variation along the length is relatively small. In this study, the rate of cross-sectional change along the length of a forming roll has been increased. Moreover, the angle between the bend line and longitudinal axis has been increased up to 15 degrees. The variable sections of the forming rolls have been designed for high strength steel parts with a symmetric u-type cross-section that varies linearly and symmetrically along the longitudinal axis.

열간 압연 공정의 신근사해법 (An Approximate Analysis of Host Strip Rolling-a New Approach)

  • 전만수;강윤호;황상무
    • 대한기계학회논문집
    • /
    • 제14권5호
    • /
    • pp.1155-1165
    • /
    • 1990
  • 본 연구에서는 롤압력과 롤토크를 예측하는 새로운 방법이 제시된다. 이 방 법은 롤 간극에서의 자세한 변형도속도의 분포를 예측할 수 있으며, 특히 롤압력과 롤 토크의 계산에 필요한 유동응력 분포도 계산할 수 있다. 이 방법을 이용하여 압연조 건과 재료성질이 롤압력, 압하력, 롤토그 등에 미치는 영향을 조사하였다. 또한, 이 방법에 의해서 예측된 결과를 참고문헌과 포항제철의 공정 데이터로부터 발췌한 실험 데이터와 비교하였으며, 유한요소 해석결과와도 비교하였다.

인쇄 롤의 간접식 레이저 가공을 위한 코팅과 에칭 기술 (Coating and Etching Technologies for Indirect Laser processing of Printing Roll)

  • 이승우;김정오;강희신
    • 한국레이저가공학회지
    • /
    • 제16권4호
    • /
    • pp.12-16
    • /
    • 2013
  • For mass production of electronic devices, the processing of the printing roll is one of the most important key technologies for printed electronics technology. A roll of printing process, the gravure printing that is used to print the electronic device is most often used. The indirect laser processing has been used in order to produce printing roll for gravure printing. It consists of the following processing that is coating of photo polymer or black lacquer on the surface of printing roll, pattering using a laser beam and etching process. In this study, we have carried out study on the coating and etching for $25{\mu}m$ line width on the printing roll. To do this goals, a $4{\mu}m$ coating thickness and 20% average coating thickness of the coating homogeneity of variance is performed. The factors to determine the thickness and homogeneity are a viscosity of coating solution, the liquid injection, the number of injection, feed rate, rotational speed, and the like. After the laser patterning, a line width of $25{\mu}m$ or less was confirmed to be processed through etching and the chromium plating process.

  • PDF