• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.740-745
• /
• 2001

The plastic deformation behavior of formed CICC fur the superconducting Tokamac fusion device was examined and appropriate manufacturing information was provided. A relation between travel of the bending roller and spring back displacement was obtained via virtual manufacturing. The radius of CICC after forming was expressed as a function of the bend-roll travel. The maximum von Mises stress after spring back was also monitored fur the SAGBO prediction. Next, the variation of the CICC cross-sectional area was examined during the first turn and during conduit bending with the largest curvature. Finally, the coil radius was measured and compared with the data generated from the virtual manufacturing. The measured data showed similar pattern as predicted one. Using the mapping function found to match with the real data, the data from the virtual manufacturing may facilitate accurate manufacturing.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.950-955
• /
• 2003

The fluid propulsion mechanism of two oscillating flat plates is studied numerically using a discrete vortex method. Presently, the flat plates are assumed to be rigid. To analyze the closely coupled aerodynamic interference between the flat plates, a core addition scheme and a vortex core model are combined together. A calculated wake pattern for a flat plate in heaving oscillation motion is compared with the flow visualization. The effect of wake shapes on the aerodynamic characteristics of the flat plate in pitching oscillation is investigated. The velocity profiles behind the flat plates in pitching oscillations are plotted to investigate the possible thrust generation mechanism.

• Journal of Magnetics
• /
• v.15 no.1
• /
• pp.36-39
• /
• 2010

The multi-degrees of freedom surface permanent-magnet motor (Multi-D.O.F. SPM) has several degrees of freedom operations that are defined as the "roll", "yaw", and "pitch". Normally, the torque that is generated to rotate a rotor includes ripples. The analysis of the torque ripples is important for improving motor performance. In terms of the electric analysis, torque ripple occurs as a result of many factors, including the rotor and stator structures, the distribution of the air-gap flux density, and the waveform of the current in the coils. In particular, the torque ripple is an important factor in the stable operation of the Multi-D.O.F. SPM. Therefore, in this work, the torque ripple was analyzed using various types of magnetization for the permanent magnet. An improved model was proposed for the Multi-D.O.F. SPM based on this analysis.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.3
• /
• pp.11-20
• /
• 2010

The purpose of this study is the investigation of the wave interaction with the rectangular floating breakwater. The flow profile obtained by PIV technique is represented to understand the vortical flow due to the wave interaction with a rectangular floating breakwater in the roll motion and the fixed condition. Also, the transmission coefficients are compared in both conditions over the extensive wave periods, which represent the performance of breakwater to attenuate the incoming waves. These results would be applied to design the floating breakwater having the mooring system to improve its performance for a certain wave period.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.75-79
• /
• 2016

A helical nanosturctrue can be obtained by self-assembly method. Utilizing DPD simulation coarse-grained model, we patterned 2D layer nanosheets with repeated diagonal defects and grafts, and programed to self-roll into hollow helix structure. The defected pattern side caused anisotropy, and formed helix or helix-like structure. This opens the possibility to control the helix pitch or cavity radius. In this work, we designed several patterns about diagonal defect with a variety of defect side densities and defect widths and then simulation was carried out. Thus, our results have that parameters are affecting self-assembly of nanosheets and their conformation.

• Proceedings of the Korean Society of Plant Pathology Conference
• /
• 2003.10a
• /
• pp.121.2-122
• /
• 2003

Since the demonstration that the transgenic plants expressing tobacco mosaic virus(TMV) coat protein(CP) gene showed resistance to TMV infection, there have been numerous attempts to produce virus-resistant plant by introducing of a part of or modified viral genome. This study was conducted to investigate the characterization and variability of disease outbreak of transgenic potato(T-potato) with the CP gene of potato leaf roll virus(PLRV) in an isolated field from 2000 to 2002. In the field inspection, incidence of PLRV on T-potato showed only 3.5％, while non-transgenic potato(N-potato) revealed 13.4％. Infection rate of PLRV was considerably low on T-potato with 4.2％ compared to 15.4％ of N-potato in ELISA tests. Those of potato virus M, potato virus Y and potato virus X on both potatoes were not statistically different. Infection of potato virus A was not observed on both potatoes. Incidence of potato late blight caused by Phytopkhora infestans on T-potato and N-potato did not differ each other with 52.7％, and 50.8％, respectively, Mating type of the causal fungus isolated from both potatoes was all Al types. Results indicates that the CP gene of PLRV affects specifically to the virus in the transgenic potato.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.142-152
• /
• 2016

GPS is not able to be used for indoor positioning and currently most of techniques emerging to overcome the limit of GPS utilize private wireless networks. However, these methods require high costs for installation and maintenance, and they are inappropriate to be used in the place where precise positioning is needed as in indoor parking lots. This paper proposes a vehicular indoor positioning method based on QR-code recognition. The method gets an absolute coordinate through QR-code scanning, and obtain the location (an relative coordinate) of a black-box camera using the tilt and roll angle correction through affine transformation, scale transformation, and trigonometric function. Using these information of an absolute coordinate and an relative one, the precise position of a car is estimated. As a result, average error of 13.79cm is achieved and it corresponds to just 27.6% error rate in contrast to 50cm error of the recent technique based on wireless networks.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.113.1-113.1
• /
• 2011

PEMS (printed electro-mechanical system) is fabricated by means of various printing technologies. Passive and active compo-nents in 2D or 3D such as conducting lines, resistors, capacitors, inductors and TFT(Thin Film Transistor), which are printed withfunctional materials, can be classified in this category. And the issue of PEMS is applied to a R2R process in the manu-facturing process. In many electro-devices, the vacuum process is used as the manufacturing process. However, the vacuum process has a problem, it is difficult to apply to a continuous process such as a R2R(roll to roll) printing process. In this paper, we propose an ESD (electro static deposition) printing process has been used to apply an organic solar cell of thin film forming. ESD is a method of liquid atomization by electrical forces, an electrostatic atomizer sprays micro-drops from the solution injected into the capillary with electrostatic force generated by electric potential of about several tens kV. ESD method is usable in the thin film coating process of organic materials and continuous process as a R2R manufacturing process. Therefore, we experiment the thin films forming of PEDOT:PSS layer and active layer which consist of the P3HT:PCBM. The organic solar cell based on a P3HT/PCBM active layer and a PEDOT:PSS electron blocking layer prepared from ESD method shows solar-to-electrical conversion efficiency of 1.42% at AM 1.5G 1sun light illumination, while 1.86% efficiency is observed when the ESD deposition of P3HT/PCBM is performed on a spin-coated PEDOT:PSS layer.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.39 no.6
• /
• pp.826-837
• /
• 2015

This study analyzes the shapes of the adjustment of a Napoleon Collar which combines a stand collar with an upper collar. It established experimental conditions for fixing the conditions of Napoleon Collar components (lapel width, stand collar size and upper collar size) as well as varied the shape of the neckline, the length of the curve of a stand collar and the size of the drawing space at the center back. It produced 22 test clothes of muslin, which were dressed on dress form No. 8. The results indicate that: 1. Neckline shape determines the amount of stand and fall. Less curved neckline stands higher against the neck and a more curved neckline is laid lower onto the body. 2. A shorter curve length of a stand collar allows a longer roll line to fall farther away from the neck with more space between the neck and collar. However, the longer the depth of curve of a stand collar creates a shorter roll line that stands high against neck and closer to neck without any space between the neck and collar with a collar line matching the neck of the dress form. 3. The smaller the drawing space at the center back creates a shorter the style line of the upper collar. However, a narrower back width of the collar creates a bigger drawing space at the center back with a longer the style line and a more naturally placed back width of the collar. 4. A Napoleon Collar creates a longer depth of curve for a stand collar and a smaller drawing space at the center back that is tightly and stably stuck to the neck.

• Journal of Oral Medicine and Pain
• /
• v.40 no.3
• /
• pp.115-123
• /
• 2015

Purpose: The aim of this study was to elucidate the coordination patterns of the sternocleidomastoid and posterior cervical muscles in response to symmetrical and asymmetrical jaw functions in normal adults. Methods: Twenty-seven healthy volunteers (8 females, 19 males; mean age, $30.4{\pm}2.5$ years) participated in this study. Surface electromyography (EMG) was used to record activities in the masseter, suprahyoid, sternocleidomastoid, and posterior cervical muscles at rest and during maximum tooth clenching, biting of a cotton roll with the anterior teeth, unilateral biting of a cotton roll with the posterior teeth, bilateral biting of cotton rolls with the posterior teeth, and jaw opening while seated. Normalized amplitude, activity indices, and asymmetry indices were compared between the muscles and the jaw tasks. Results: During symmetrical jaw functions (e.g., tooth clenching, biting with the anterior teeth, bilateral biting with the posterior teeth, jaw opening), the sternocleidomastoid and posterior cervical muscles showed elevated EMG amplitudes compared with the resting condition. The co-activation pattern of the sternocleidomastoid muscle was more pronounced than those of the posterior cervical muscles during these tasks. During asymmetrical jaw functions (e.g., unilateral biting with the posterior teeth), the ipsilateral sternocleidomastoid and masseter muscles showed higher contraction activity than did the contralateral muscles, but the contralateral posterior cervical muscles were more active than the ipsilateral muscles. Conclusions: The sternocleidomastoid and posterior cervical muscles were shown to be co-activated and coordinated anteroposteriorly or bilaterally according to symmetrical or asymmetrical jaw function. These results suggest an integrated neural control mechanism for the jaw and neck muscles, and provide further evidence supporting the intimate functional coupling between the trigeminal and cervical neuromuscular systems.