• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• Korean Journal of Materials Research
• /
• v.16 no.2
• /
• pp.111-115
• /
• 2006

High-finned tubes have good thermal conductivity and have better cooling efficiency than plain tubes or low-fined tubes due to bigger air contact area. During high-fined tubes are manufactured by roll forming, the main technique is illustrated to optimizing primary material(copper pipe), optimized die matrix designing technique for roll forming, control manufacturing speed to develop productivity etc. In this study, a roll forming system was developed in oder to produce high-finned tube. Also a multi-step roll forming die was designed & built to produce high-finned tube that has over 10 mm fin height. And then, roll forming test using copper pipe was performed to produce high-finned tube. Roll forming process for producing highfinned tube was optimized by analyzing and adjusting misrostructure, hardness, and surface roughness of roll formed high-fined tube.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.505-511
• /
• 1993

The results were obtained with changes according to the surface roughness of work roll and method to make the peak count on the roll in the temper rolling, and factors to affect to the work roll surface in actual rolling machine(ie. Temper mill). Conclusions are as follows. 1. E.D.T(Electro-discharge texturing)roll is more uniform roughness distribution than shot blasted roll and it's life time is two timees longer than that of shot blasted because it has more sine wave roughness. 2. The higher peak count of surface roughness, the more time is necessary to work roll texturing In shot blasting method, Surface roughness is relating to the grit size,impeller speed and hardness of roll material, But is can't control the peak count. 3. In shot blast texturing, Surface roughness of temper rolled strip which is transfered surface roughness of work roll is more ununiform than that of E.D.T roll 4. E.D.T roll has more uniform than the shot blasted roll and has more peak count than that of shot blasted roll. The surface of painted strip to image clarity is superior to that of shot blasted roll because E.D.T roll has more peak count and smooth surface.

• The monthly packaging world
• /
• s.359
• /
• pp.77-81
• /
• 2023

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.1
• /
• pp.42-49
• /
• 2016

This study was analyed V-bending in order to analyze the spring-back phenomenon in the roll forming process. The material of forming sheet used in the roll forming process is high tension steel and the product name of sheet material is POSTEN 60. The most important variable is the number of roll passes (3-Pass, 4-Pass, 5-Pass, 6-Pass and 10-Pass) and other roll forming process variables were fixed. To determine the characteristics of the tension and compression, the forming sheet was analyzed by dividing the layer (Upper and Bottom) in the thickness direction from the center line. The results of FEM simulation analysis was derived to von-mises stress equivalent strain, and the spring-back value was calculated according to the final forming shape. The more number of the roll pass, von-mises stress and equivalent strain value of forming sheet were lowed. Also, spring-back values tended to decrease. The results of this study can be utilized for prediction and trend of spring-back value in the roll forming process applied to high tension steel sheet. So, development time and cost of the roll forming process is expected to be reduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.73-85
• /
• 1997

The rolling force and roll deformation behavior in the twin roll type strip continuous casting process has been computed to estimate the thermal charcteristics of a caster roll. To calculation of rolling force, the relationship between flow stress and strain for a roll material and casting alloy are assumed as a function of strain-rate and temperature because mechanical properties of a casting materials depends on tempera- ture. The three dimensional thermal dlastic-plastic analysis of a cooling roll has also been carried out to obtain a roll stress and plastic strain distributions with the commercial finite element analysis package of ANSYS. Temperature fields data of caster roll which are provided by authors were used to estimated of roll deformation. Roll life considering thermal cycle is calculated by using thermal elastic-plastic analysis results. Roll life is proposed as a terms of a roll revolution in the caster roll with and without fine failure model on the roll surface. To obtain of plastic strain distributions of caster roll, thermomechan- ical properties of roll sleeve with a copper alloy is obtained by uniaxial tensile test for variation of temperature.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.10a
• /
• pp.264-267
• /
• 2001

by three-dimensional finite element method. The guide roll is an intermediately supported trans-axle miler, so called I-STAR roll, which was designed by VAI. The guide roll has been used in POSCO since 1998. Though the number of stowage in casting has been apparently decreased since thef it has occasionally been failed during operation. The simulations were carried out to find out the status of stress and deformation as well as improvement of the guide roll. The thermal effect is much more dominant than ferro-static pressure or others in stress and deformation of the guide roll. The material of the guide roll is SCM440.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.180.2-180
• /
• 2001

In the hot rolling process, the RF AGC (Roll Force Auto Gauge Control) is used to control the roll gap to reduce the variation of rolling force caused by the roll eccentricity and the variation of material thickness. However the effect of the roll eccentricity cannot be distinguished. To eliminate the effect of the roll eccentricity, the roll eccentricity estimation is needed to supplement some drawbacks of RF AGC. In this paper, an ALE(Adaptive Line Enhancer) that extracts the rolling force variation due to the roll eccentricity is suggested. We also provide an algorithm that enhances the convergence time of roll eccentricity estimation. The performance improvement of the Suggested algorithm is shown via simulations.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.136-138
• /
• 2003

Strain states of clad sheets consisted of AL3003 and SUS430 were studied by FEM simulation. Main simulation parameters include roll size, reduction, material properties, material temperature, and friction between roll and material (or friction between materials). To investigate the effect of friction on the evolution of strain states, the friction coefficient between roll and material (or fraction coefficients between materials) was varied. Components of strain rate, strain were compared according to the variation of friction coefficients. And strain states during cladding were compared with those induced by simple rolling process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.380-381
• /
• 2007

This paper reports on the deposition conditions and properties of ITO films used as electrode layer in a organic light emitting diodes on a PET substrate. The deposition technique employed was specially designed roll-to-roll sputtering. The oxide was deposited at room temperature in an argon and oxygen plasma on a transparent conducting ITO layer on a PET film. The influence of deposition parameters such as DC power, working pressure and oxygen partial pressure has been investigated, in order to obtain the best compromise between a high deposition rate and adequate electro-optical properties. Electrical and optical properties of ITO films were analyzed by Hall measurement examinations with van der pauw geometry at room temperature and UV/Vis spectrometer analysis, respectively. In addition, the structural properties and surface smoothness were measured by x-ray diffraction and scaning electron microscopy, respectively. From optimized ITO films grown by roll-to-roll sputter system, good electrical$(6.44{\times}10^{-4}\;{\Omega}-cm)$ and optical(above 86 % at 550 nm) properties were obtained. Also, the ITO films exhibited amorphous structure and very flat surface beacause of low deposition temperature.