• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.169-172
• /
• 2002

Recently, the application of 3-roll mill is increasing, because of its flexibility in spread control and stand arrangements due to its compact size. But deformation characteristics and microstructural change in the process is not well known. In this study, austenite grain size (AGS) predictions were made by isothermal FE analyses and a microstructure model available in the literature. From this study, the effect of draught on the AGS characteristics was analyzed based on the divided zones of two major recrystallization behaviors.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.300-301
• /
• 2007

In this study, it is investigated that sheet characteristics of high strength steel sheets and effect of springback. High strength steel sheets has got attention in automobile industry of high strength and high formability. Springback is a common phenomenon in sheet metal forming, caused by the elastic recovery of the internal stresses after removal of the tooling. However, the information in deformation behavior of high strength steel sheets, including bending and sheet characteristics and springback, is not enough until now. In this research, the V-bending experiment and analysis have been done to obtain the information of springback of high strength steel sheets. Tensile test for high strength steel sheets was done to got tensile properties of elastic modulus and flow stress of the material. It analyzed springback according to the sheet characteristics with using roll-forming model. FE-Simulation used DEFORM-$3D^{TM}$.

• Journal of Ship and Ocean Technology
• /
• v.7 no.1
• /
• pp.29-35
• /
• 2003

Intensive experimental investigation has been conducted on the characteristics of model tank with intruded flow. The remaining flow inside tank contribute to the dynamic behavior and further closely related to the stability of vessel as well. To understand the importance of the trapped flow and its dynamic effects a series of systematic tests were conducted using a bench tester that could generate periodic roll motion and also complex motions of combined roll-heave-sway. To accommodate experimental conditions and to create three degree freedom of motions, a bench tester was fabricated and verified. Having similarities in terms of flow trapped inside tank, theoretical approaches for A.R.T. were applied to the study. The major parameters including roll angle, period and flow height were varied in the experiments to obtain the characteristics of model tank.

• Fibers and Polymers
• /
• v.7 no.4
• /
• pp.424-431
• /
• 2006

Roll drafting, a mechanical operation attenuating fiber bundles to an appropriate thickness, is an important operation unit for manufacturing staple yams. It influences not only the linear density regularity of the slivers or staple yams that are produced, but also the quality of the textile product and the efficiency of the thereafter processes. In this research, the dynamic states of the fiber bundle in the roll drafting zone were analyzed by simulation, based on the mathematical model that describes the dynamic behavior of the flowing bundle. The state variables are the linear density and velocity of the fiber bundles and we simulated the dynamics states of the bundle flow, e.g., the profiles of the linear density and velocity in the draft zone for various values of the model parameters and boundary conditions, including the initial conditions to obtain their influence on the dynamic state. Results showed that the mean velocity profile of the fiber bundle was strongly influenced by draft ratio and process speed, while the input sliver linear density has hardly affected the process dynamics. Velocity variance of individual fibers that could be supposed to be a disturbing factor in drafting was also influenced by the process speed. But the major disturbance occurred due to the velocity slope discontinuity at the front roll, which was strongly influenced by the process speed. Thickness of input sliver didn't play any important role in the process dynamics.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.2
• /
• pp.330-340
• /
• 2009

A naval shipboard inevitably movies in a pitch and roll direction under the influence of wave and wind in the sea. As a result, the shipboard gets in a continuous turning motion back/front and right/left. And the shipboard is also constantly exposed to many different kinds of disturbance signals including the vibrations of various frequencies from the internal equipments and their vibrations, strong waves, and impact from explosion. This paper formulates multi-body dynamic models similar to an actual system and simulates the pitch/roll positions of a 2-axes gimbals with PI controller for consecutive behavior of a naval shipboard including disturbance.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.225-231
• /
• 2001

A mathematical model for the analysis of roll gap phenomena in the strip temper rolling process is described. A new approach to solve the roll indentation and diverging problem in modeling of severe temper rolling cases is obtained by adopting the preliminary displacement principle of two contacted rough bodies to describe the friction behavior in the roll gap. The mechanical peculiarities of the temper rolling process, such as a high friction value with high roughness rolls and a non-circular contact arc, low reduction and non-negligible entry and exit elastic zones as well as central preliminary displacement zone etc., are all taken into account. The deformation of work rolls is calculated with the influence function method and an arbitrary contact are shape is permitted. The strip deformation is modeled by the slab method and the entry and exit elastic deformation zones are included. The preliminary displacement principle is used to determine the boundaries and to calculate the friction of the central preliminary displacement zone. The model is calibrated against the production mill data and installed in the setup computer of a temper rolling mill in POSCO. The validity and precision of the model have been proven through a comparison of the measured roll forces and the predicted ones.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.784-789
• /
• 2018

Accurate aerodynamic characterization of projectile is crucial for successful development of munition. The aerodynamic characterization of fin stabilized projectile is more difficult than characterization of traditional symmetric ballistic projectile. Instrumented free flight experiments were conducted to quantify rolling behavior of fin stabilized projectile. The instrumented projectiles were launched from a rifled tube and the onboard sensor data were acquired through a telemetry transmitter. Roll rate was measured for fin stabilized projectile by means of an angular rate sensor. And, roll damping coefficients were estimated from onboard sensor data acquired during gun firing and trajectory analysis of mathematical model.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.209-216
• /
• 2000

The lateral behavior of the moving web is critical to the quality of the web products. The alignment of the rollers carrying the web is found to be one of important factors to the lateral behavior of the moving web. But, the study on the effect of the tilting roller in the direction of the normal to the moving web on the lateral behavior has not been reported in the literature yet. For example, the contact roller often contacts the winding roll in a tilted fashion and causes the lateral motion of the winding web, which induces the offset on the wound roll. The lateral dynamics of the moving web induced by a tilted roller in normal direction of a web is investigated in this paper. The two-dimensional dynamic model developed by Shelton is extended to investigate the effect of a titled roller in a normal direction of the moving web on the lateral motion of the moving web. New boundary conditions are developed to solve the extended model. Computer simulation study proved that the model developed can be used to predict the lateral motion of the moving web ？ to a tilted roller in normal direction of the moving web. The lateral deflection is increased exponentially a the tilting angle is increased. As the length of web span is increased, the amount of lateral deflection was increased almost linearly for the same tilting angle. The lateral dynamics turned out to be almost independent to the operating tension. The model developed can be used to solve the offset problem of the staggered winding and also to design a new web guiding mechanism.

• Tribology and Lubricants
• /
• v.33 no.3
• /
• pp.98-105
• /
• 2017

A pin-on-disk test is performed to measure the wear volume of a ductile cast iron (DCI) roll when it wears down using a high carbon steel and two alloy steels at different sliding velocities between the roll and the material (steel). Normal pressure is set as constant and test temperatures are 400, 500 and $600^{\circ}C$. In addition, thermal softening behavior of the DCI roll is examined using a high-temperature micro-hardness tester and the surface hardness variation of the DCI roll is expressed in terms of temperature and heating time. Based on experimental data, a wear coefficient used in Archard's wear model for each material is obtained. The wear volume is clearly observed when the test temperature is $400^{\circ}C$ and sliding velocity varies. However, it is not measured at temperatures of $500^{\circ}C$ and $600^{\circ}C$ even with variations in sliding velocity. From the optical photographs of the pin and disk, the abrasive wear is observed at $400^{\circ}C$ clearly, but no at $500^{\circ}C$ and $600^{\circ}C$. At higher temperatures, the pin surface is not smooth and has many tiny caves distributed on it. It is found that wear volume is dependent on the carbon contents rather than alloy contents. Results also reveal that the variations of wear coefficients are almost linearly proportional to the carbon contents of the material.

• Journal of Korean society of Dental Hygiene
• /
• v.10 no.2
• /
• pp.269-282
• /
• 2010

Objectives : The purpose of this study was to investigate attitudes toward and practice of oral health management among adults in the Gumi area. Health behavior especially drinking and smoking have been proven to affect the tissues around the teeth and increasing in importance. Thus the study set out to examine oral management according to drinking and smoking to suggest a need for education about oral health and provide basic data for oral health education. Methods : Total 226 subjects, who consist of 141 male adults and 85 female adults, in Gumi were asked to fill out a self-administered questionnaire on October 24, 2009. Their answers to the items about general characteristics, health behavior, and oral health behavior were analyzed with the SPSS WIN 12.0 program. Results : 1. As for the frequency of visiting a dental clinic(hospital) for the last year, the non-movement group recorded higher frequency than the movement group, and the drinking group also did than the non-drinking group(p<0.05). 2. As for the experience and frequency of scaling, the female subjects were higher in the experience and frequency of scaling than their male counterparts. The older they got, the more they tended to have scaling. The married respondents had more experiences of scaling than the singles, and the non-drinking group was high in the experience of scaling(p<0.05). 3. As for the number, time, and method of toothbrushing a day, more women answered they brushed teeth three times or more per day than men; those who were in their forties were the highest in terms of the roll method, and those who were in their twenties were the highest in terms of toothbrushing time. The married group and the non-smoking group answered they brushed teeth in the roll method three times or more per day in higher percentage. And the non-drinking group was high in the roll method, which was statistically significant(p<0.05). 4. As for use and kinds of auxiliary oral hygiene devices, the female respondents used them more than their male counterparts. The older they became, the more they used them. The married group, the non-smoking group, and the non-drinking group used such devices a lot. The smoking group used dental floss most, and the non-smoking group used more kinds of such devices than the smoking group, which was statistically significant(p<0.05). Conclusion : Oral diseases can be prevented by adopting healthy and right oral management behavior. Using the findings of the study, more diverse programs about actual oral health education should be activated so that people can change their bad oral management and behavior and develop a habit of the right oral management attitude.