• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.95-103
• /
• 2010

Roll to Roll (R2R) is one of the most promising production technologies in the printed electronics such as OLEDs, e-paper, backplanes, RFID because this technology can save production cost and increase production speed. Printed electronics includes various processes such as printing, drying, winding, unwinding, and so on. In printed electronics R2R system, air-flotation oven is employed for drying process. Therefore, it is essential to introduce efficient and fast drying process when printing is finished. This paper considers the analysis of drying process in R2R that involves hot air flow. Air-flotation oven consists of non-contact supports and drying of coated web materials such as plastic films and paper. In this paper, experimental results and numerical analysis of pressure-pad air bar are investigated. The aerodynamic characteristics of pressure-pad air bar are numerically calculated using computational fluid dynamics (CFD) approach. Then the measured values of the aerodynamic forces for air bars are compared with those of CFD analysis.

• 한국전기전자재료학회논문지
• /
• 제26권6호
• /
• pp.462-467
• /
• 2013

In this paper, we analyzed the effects of doctoring process on the patterns of Ag ink in gravure off-set printing. The parameters of doctoring process were the angle and the pressure, which was represented by the depth of blade movement to the gravure roll, of doctor blade to the surface of gravure roll, and the angle of patterns engraved on the gravure roll to the doctor blade moving direction. The proper parameters were extracted for the fine patterns and they were 15 mm for the pressure, $60^{\circ}$ for the blade angle. And the angle of patterns with respect to the blade movement should be less than $40^{\circ}$ for the best results. The gravure off-set printing with the above parameters was carried out to print gate electrodes and scan bus lines of OTFT-backplane for e-paper. The line width of $50{\mu}m$ was successfully obtained. The thickness of electrodes was $2.5{\mu}m$ and the surface roughness was $0.65{\mu}m$ and the sheet resistance was $15.8{\Omega}/{\Box}$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.65-66
• /
• 2006

Dancer systems are most widely used mechanism for attenuation of tension disturbances. Lately, demands fur high speed converting machines over 500mpm(m/min) are raising but domestic converting industries can not come up with the machines because capacities for a designing of the converting machine are restricted lower than 300mpm. Moreover roll-to-roll is attracted flexible display manufacturer's attention as a effective method for productivity. A constant tension level in the span before the first printing cylinder is the key of high speed quality printing. This paper presents a modeling and simulations of dancer systems on converting machines.

• 한국기계가공학회지
• /
• 제12권5호
• /
• pp.23-29
• /
• 2013

Recent advances in printing technology have increased the productivity of the roll-to-roll (R2R) printing process for printed circuitry. In the R2R printed electronics, characteristics of printed and coated layers are one of the most important issues that determine the functional quality of final products. The slot-die technology can coat a large area with high uniformity using low-viscosity materials; determining the process parameters is important to obtain excellent coating qualities. In this study, a viscocapillary model was used to predict qualities of coated layers and patterns. On the basis of analysis results, a novel meta model was derived using design of experiment methodology to improve accuracy. Sensitivity analysis was performed to define major parameters in R2R slot-die coating process. The coating speed was found to most significantly affect the coated layer thickness and was easily controlled. The performance of the proposed model is verified through experimental studies. Based on the statistical analysis results, R2R slot die process can be optimized to guarantee a desired thickness.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.262-263
• /
• 2011

Flexible electronics, a future technology of electronics, require a low cost integrated circuit that can be built on various types of the flexible substrates. As a potential candidate for this application, a single walled carbon nanotube network is studied as an active device with a scheme of thin film transistor. Transistors are formed on a plastic foil by the Roll-to-Roll (R2R) and the Roll-to-Device (R2D) printing method. For both printing methods, electrical transports for the transistors are presented with the temperature dependence of threshold voltage (V_Th) and mobility from the measured transfer curves at temperatures ranging from 10 K to 300 K. It is observed that ${\mu}=0.044cm^2/V{\cdot}sec$ and V_Th=7.28V for R2R and ${\mu}=0.025cm^2/V{\cdot}sec$ and V_Th=3.10V for R2D, both for the temperature at 300K. Temperature dependence of mobility and V_Th is observed. However for R2R, the temperature dependence of V_Th is constant. It is the difference between, R2R and R2D.

• 마이크로전자및패키징학회지
• /
• 제21권4호
• /
• pp.15-24
• /
• 2014

Recently, a variety of printing technologies, including ink jet, gravure, and roll-to-roll (R2R) printing, has generated intensive interest in the application of flexible and wearable electronic devices. However, the actual use of printing technique is much limited because the sintering process of the printed nanoparticle inks remains as a huge practical drawback. In the fabrication of the conductive metal film, a post-sintering process is required to achieve high conductivity of the printed film. The conventional thermal sintering takes considerable sintering times, and requires high temperatures. For application to flexible devices, the sintering temperature should be as low as possible to minimize the damage of polymer substrate. Several alternative sintering methods were suggested, such as laser, halogen lamp, infrared, plasma, ohmic, microwave, and etc. Eventually, the new sintering technique should be applicable to large area, R2R, and polymer substrate as well as low cost. This article reviews progress in recent technologies for several sintering methods. The advantages and disadvantages of each technology will be reviewed. Several issues for the application in R2R process are discussed.

• 펄프종이기술
• /
• 제46권3호
• /
• pp.1-10
• /
• 2014

Offset paper printing is a promising roll-to-roll technique for color printed materials. Although it is no doubt that understanding ink transfer mechanism in offset printing process is necessary to achieve high printing quality, investing the relationship between inks and substrates at the nip is difficult experimentally due to high printing speed. In this paper, rheological behavior and splitting point of the ink at the nip is studied using package software Ployflow and Flow 3D based on Navier-Stokes equation. Polydimethylsiloxane (PDMS) ink and IGT printability tester were used for an model ink and experiment to compare with that of simulation data, respectively. As a result, higher viscosity at state flow and pressure increased ink transfer due to higher possibility of presence of cavitation at the nip and increase in covering area ratio. These results have shown good agreements with experimental data compared by measuring density of print through.

• 동력기계공학회지
• /
• 제13권3호
• /
• pp.59-64
• /
• 2009

This study presents a new approach to pressure control of a impression cylinder for roll coater which is a kind of face pressure control between blanket roll and impression roll. Roll-to-Roll method for printing is a very useful tool for mass production such as RFID elements, smart sensors and solar cell devices. In this study, a decupling control strategy of the roll coater which is a combination of a cylinder system, a dry system and two pressure regulators with two pneumatic cylinders was discussed. Also, the characteristics of component such as a pressure regulator having a pressure reducing function and the movement of a blanket roll and a impression cylinder were analyzed using the Matlab software. From this results, the techniques of a shock and a vibration reduction were suggested.

• 대한전자공학회논문지SD
• /
• 제48권6호
• /
• pp.7-14
• /
• 2011

본 논문은 PDMS(polydimethyl siloxane) 스탬프를 이용한 원통형 마이크로 접촉인쇄(roll-type micro-contact printing)에 관한 것으로 대면적 플라스틱 기판에 미세 금속 전극 인쇄를 PDMS 스탬프의 평탄화, 은 나노 잉크의 은 함량, 공정변수인 코팅속도, 잉킹속도, 프린팅속도, 프린팅 압력을 조절하여 가장 우수한 인쇄특성을 나타내는 조건을 도출하였다. 그 결과 면적 $4.5cm\;{\times}\;4.5cm$ 기판에 최소선폭 10 um, 두께 300 nm, 표면거칠기 40 nm 이하, 비저항 $2.08\;{\times}\;10^{-5}{\Omega}{\cdot}cm$의 특성을 갖는 은미세 전극을 인쇄하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.81-82
• /
• 2010