• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1998.11a
• /
• pp.35-39
• /
• 1998

형광등용 조명기구에 사용되는 경면 반사판의 형상설계 프로그램(SpeROD)을 개발하였다. 이 프로그램은 조명기구 설계시의 많은 시행착오를 줄이고 설계시간을 단축시키며, 손쉽게 조명기구를 설계할 수 있게 도와준다. SpeROD(Specular Reflector Optical Designer)는 2차원적인 형상설계 과정을 밟으며, 대칭형태의 반사판을 기초로 한다. SpeROD의 주요 관점은 배광의 만족과 효율의 개선이다. SpeROD를 이용하여 설계된 반사판형태에 대하여 배광예측 프로그램을 통하여 배광을 시뮬레이션 해 본 결과, 배광면에서는 만족스러운 결과를 얻을 수 있었으며, 효율면에서도 상당한 진전을 가져올 수 있었다. SpeROD는 조명기구 반사판 설계시 간편화와 신속화에 도움을 줄 것이다.

• Proceedings of the KIEE Conference
• /
• 2003.07a
• /
• pp.293-295
• /
• 2003

KEPCO's high voltage distribution power line laid under the ground near to the J-booster pumping station that supply water for living. Lightening rod equipment does not installed at the J-booster pumping station because KEPCO's over head ground wire for protection functions as a lightening rod equipment. In this study, it is concerned whether KEPCO's over head ground wire for protect the distribution power line affect to the J-booster pumping station which is installed for reduce the damage from the direct and indirect lightening. If KEPCO's protection area does not affect to the J-pumping station, it is plan to examine the construction method of lightening rod protection angle and lightening rod equipment and to suggest the optimum protection plan using the surrounding structure based on the suitability of protection area.

• Journal of ILASS-Korea
• /
• v.13 no.1
• /
• pp.9-15
• /
• 2008

This experimental study was carried out to examine the heat transfer characteristics of impinging air jet on a flat plate with a set of right angled triangle rods. Each right angled triangle rod in the array was positioned normal to the flow direction and parallel to the flat plate surface. The clearances from a right angled triangle rod to flat plate surface (C=1, 2 and 4 mm) and the distance from nozzle exit to flat plate (H=100 and 500 mm) were changed for the pitch between each right angled triangle rods (P=40 mm). As a result, heat transfer shows best performance at the clearance of C=1 mm, in case clearance changed, and the average heat transfer enhancement rate increased up to 47% compared to the result of a flat plate without a right angled triangle rod.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.71-78
• /
• 2002

The N-value from the standard penetration test(SPT) is affected by the magnitude of the rod penetration energy transmitted from the falling hammer as well as the geotechnical characteristics of the ground. Understanding of the striking energy efficiency in the SPT equipment is getting important for that reason. The energy efficiencies of the various type of equipment were investigated through field tests using the instrumented rod and wave-signal acquisition systems including the pile driving analyzer(PDA). The rod energy ratio, ERr was defined as the ratio of the energy delivered to the drilling rod to the potential free-fall energy of the hammer. It appears that the type of the hammer and lift/drop system had a strong influence on the energy transfer mechanism and ERr also varies according to the energy instrumentation system and the analysis methods.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1650-1652
• /
• 2003

In this study, in order to increase electric field intensify near a lightning rod a floating conductor is adopted. If a floating conductor is located near the lightning rod, the positive and negative charges are equally induced on the lightning rod and the floating conductor, and the local electric field intensity near them increases. This increase of electric field intensity can ignite easily the ionization process of the surrounding air and the corona phenomenon begins there. It occurs before the usual lightning process begins on the top of the conventional rod. The charges of the ground or some buildings are omitted during the corona process through the floating conductor. Therefore, the probability of the main lightning on the conventional rod can be reduced.

• Nuclear Engineering and Technology
• /
• v.36 no.2
• /
• pp.153-164
• /
• 2004

A computational fluid dynamics (CFD) analysis has been performed to investigate the turbulent flow and heat transfer in a triangular rod bundle with pitch-to-diameter ratios (P/D) of 1.06 and 1.12. Anisotropic turbulence models predicted the turbulence-driven secondary flow in a triangular subchannel and the distributions of the time mean velocity and temperature, showing a significantly improved agreement with the measurements from the linear standard $k-{\epsilon}$ model. The anisotropic turbulence models predicted the turbulence structure for a rod bundle with a large P/D fairly well, but could not predict the very high turbulent intensity of the azimuthal velocity observed in the narrow flow region (gap) for a rod bundle with a small P/D.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.593-602
• /
• 2004

We have developed a digital control rod control system not only to improve its performance but also to improve its reliability and speed of response so that it can replace the old fashioned analog system. However, a new developed digital control system should be tested to prove the validity by using any prototype or mock-up before application. The reliability prediction and the reliability block diagram analysis methods were adopted to verify the reliability of the developed hardware. For the case of software, especially fur a new developed control algorithm it has been tested to prove performances and validation by using a dynamic simulator and mock-up of control rod drive mechanism altogether. Here we want to present some key factors regarding to the new developed digital system with some verification procedures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.177-183
• /
• 1997

The fuel rod for PWR is supported by the spring of the sapcer grid to maintain its axial location and lateral space between fuel rods to get proper functions during the residence in the reactor. The long exposure duration makes the spring to be relax and loss the spring force that results in a fuel rod rattling which may cause fuel rod failure. Here considering the spring behaviour as a function of burnup the reaction forces of the springs are calculated by the finite element program developed herein to evaluate the integrity of the fuel rod from fretting. The results are compared with previous data and ANSYS for the validation of the program and procedures.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.66.4-66
• /
• 2001

In this paper we have fabricated the two-dimensional Rod Balancing System which expands conventional one-dimensional inverted pendulum control system and designed its controller. The X-axis cart and Y-axis bar of the Rod Balancing System, which is composed of X-Y table, are actuated through timing belt by each of two geared DC motors, and the rod mounted on a X-axis cart can be brought to the desired position and maintained in a vertical position by motor-control. For the control of the Rod Balancing System, we used a fuzzy logic controller that is an approach to systems control when the exact mathematical model of the plant is unknown or the mathematical model is too complex to understand.

• Nuclear Engineering and Technology
• /
• v.52 no.12
• /
• pp.2887-2900
• /
• 2020

Cladding failure in a fuel rod during operation in a BWR is analyzed using a FALCON code-based model. Comparative calculation with a neighbouring, intact rod is presented, as well. A considerable 'hot spot' effect in cladding temperature is predicted with the SLICE-DO model due to a thermal barrier caused by the localized crud deposition. Particularly significant overheating is expected to occur on the affected side of the cladding of the failed rod, in agreement with signs of significant localized crud deposition as revealed by Post Irradiation Examination. Different possibilities (criteria) are checked, and Pellet-Cladding Mechanical Interaction (PCMI) is shown to be one of the plausible potential threats. It is shown that PCMI could lead to discernible concentrated inelastic deformation in the overheated part of the cladding. None of the specific mechanisms considered can be experimentally or analytically identified as an only cause of the rod failure. However, according to the current calculation, a possibility of cladding failure by PCMI cannot be excluded if the crud thickness exceeded 300 ㎛.