• 대한기계학회논문집A
• /
• 제29권9호
• /
• pp.1161-1168
• /
• 2005

As a result of vehicle maintenance of rocker arm shaft for 4-cylinder SOHC engine, failure analysis of rocker arm shaft is needed. Because more than $30\%$ of vehicles investigated have been fractured. Failure analysis is classified into an naked eyes, microscope and X-ray fractography etc. It can predict applied load as well as load type. These methods are applicable to components with simple boundary condition but aren't applicable to components with complex boundary condition. The existing fractography don't catch hold of failure boundary condition quantitatively. Especially, in case that the components isn't fractured at same position. We must determine the most dangerous failure boundary condition to evaluate their operation mechanism. The effect of various factors on response should be estimated to solve this statical problem. This study presents the most dangerous failure boundary condition of rocker arm shaft using orthogonal array and ANOVA in order to assure its robustness.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.130.2-130.2
• /
• 2005

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.84-90
• /
• 2007

As a result of vehicle maintenance of rocker arm shaft for 4-cylinder SOHC engine, failure stress analysis of rocker arm shaft is needed. Because more than 30% of vehicles investigated have been fractured. Failure stress analysis is classified into an naked eyes, microscope, striation and X-ray fractography etc. Failure stress analysis by using striation is already established technology as means for seeking cause of fracture. But, although it is well known that striation spacing corresponds to the crack growth rate da/dN, it is not possible to determine ${\sigma}_{max}\;and\;{\sigma}_{min}$ under service loading only from striation spacing. This is because the value of striation spacing is influenced not only by ${\Delta}K$ but also by the stress ratio R. In the present paper, we determine the stress ratio using orthogonal array and ANOVA, and propose a prediction method of failure stress which is combined with FEM and striation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.198-202
• /
• 2004

This study proposes a new optimization algorithm which is combined with genetic algorithm and ANOM. This improved genetic algorithm is not only faster than the simple genetic algorithm, but also gives a more accurate solution. The optimizing ability and convergence rate of a new optimization algorithm is identified by using a test function which have several local optimum and an optimum design of rocker arm shaft. The calculation results are compared with the simple genetic algorithm.

• 대한기계학회논문집A
• /
• 제29권6호
• /
• pp.835-841
• /
• 2005

This study proposes a new optimization algorithm which is combined with genetic algorithm and ANOM. This improved genetic algorithm is not only faster than the simple genetic algorithm, but also gives a more accurate solution. The optimizing ability and convergence rate of a new optimization algorithm is identified by using a evaluation function which have several local optimum and an optimum design of rocker arm shaft. The calculation results are compared with the simple genetic algorithm.

• Journal of Biosystems Engineering
• /
• 제19권3호
• /
• pp.163-174
• /
• 1994

This study was conducted to investigate the dynamic motion of knife drive system of combine harvester. A computer program was developed to simulate the dynamic motion of the knife drive linkage and its algorithm was evaluated through experiments. The results are summarized as follows : 1. The theorectical horizontal (the direction of knife's reciprocating motion) reaction forces at the supporting point of rocker arm and crank arm were changed in the similar sinusoidal trends with the measured reaction forces. 2. The maximum values of shaking moment and reaction force per one revolution of crank arm followed polynomial trends as the rotational speed of crank shaft increased. The unbalanced force acting on the driving system increased at high speed. Therefore, the rotational speed of crank shaft should be maintained in proper range at increased forward speed to decrease vibration of the knife drive system. 3. The added mass to the crank arm increased the dynamic unbalanced force at the supporting point of rocker arm. It counterbalanced the reaction force at the supporting point of crank arm.

• 한국기계가공학회지
• /
• 제9권6호
• /
• pp.7-15
• /
• 2010

Recently, with the high performance and efficiency of machine, there have been required the multi-functions in various machine parts, such as the heat resistance, the abrasion resistance and the stress resistance as well as the strength. Fatigue crack growth tests were carried out to investigate the fatigue characteristics of high carbon steel (SM53C) experienced by high-frequency induction treatment. The Cam nose part of the Automobile's Cam shaft is strongly bumped with rocker arm or valve-lift. Therefore abnormal wear such as unfair wear and early wear occur in the surface. This abnormal wear causes a defect that bad timing open and close actions of the engine valve happen in the combustion chamber so the fuel gas will be combustion imperfect. Therefore, the cam shaft demands high hardness and wear resistance. In this study, high frequency heat treatment has been accomplished while wear test for material SM53C.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.158-161
• /
• 2004

In recent, the automotive number of korea has risen above 14millions vehicles. The automotive was settled down goods haying to live. In a flood of this automotive the accuracy diagnosis for the vehicle certainly need for people referencing car. To do this diagnosis, the researcher has to experience many example in the field and need to system them. Expecially, the study for failure of the engine nearly research in the korea. When moving parts of engine no problem. In order to work, the engine must operate normality state. In this paper the purpose study the failure for the tribological example of engine.