• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.193-198
• /
• 2000

Switched reluctance motor drives have been finding their applications in the variable speed drives due to their relatively low cost, simple and robust structure, controllability and high efficiency. Fuzzy control does not need any model of plant. It is based on plant operator experience and heuristics. Fuzzy control is basically adaptive and gives robust performance for plant parameter variation. This paper deals with the sped control of switched reluctance motor using fuzzy controller with 7-rule based fuzzy logic. The proposed fuzzy controller is superior to the control performance of the conventional PI controller. The fuzzy controller is implemented by 80C196KC, 16 bit one-chip microcontroller.

• The Journal of Korea Robotics Society
• /
• v.6 no.2
• /
• pp.165-172
• /
• 2011

This paper presents a robust lane detection algorithm based on RGB color and shape information during autonomous car control in realtime. For realtime control, our algorithm increases its processing speed by employing minimal elements. Our algorithm extracts yellow and white pixels by computing the average and standard deviation values calculated from specific regions, and constructs elements based on the extracted pixels. By clustering elements, our algorithm finds the yellow center and white stop lanes on the road. Our algorithm is insensitive to the environment change and its processing speed is realtime-executable. Experimental results demonstrate the feasibility of our algorithm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2052-2059
• /
• 2002

In this study, a synchronous controller algorithm being applicable to two-axis position synchronzation is developed. Based on coupling structure, the synchronous control system is composed of speed and synchronous controllers. The speed controller is designed to follow a speed reference. In addition, the synchronous controller is designed from the viewpoint of accurate synchronization and robust stability in H$\infty$ synthesis. Finally, the effectiveness of the presented controller is demonstrated through extensive experiments.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1357-1368
• /
• 2017

The lack of controllability over the wind causes fluctuations in the output power of the wind generators (WGs) located at the wind farms. Distribution Static Compensator (DSTATCOM) equipped with Battery Energy Storage System (BESS) can significantly smooth these fluctuations by injecting or absorbing appropriate amount of active power, thus, controlling the power flow of WGs. But because of the component aging and thermal drift, its harmonic filter parameters vary, resulting in performance degradation. In this paper, Quantitative Feedback Theory (QFT) is used as a robust control scheme in order to deactivate the effects of filter parameters variations on the wind power generation power smoothing performance. The proposed robust control strategy of the DSTATCOM is successfully applied to a microgrid, including WGs. The simulation results obviously show that the proposed control technique can effectively smooth the fluctuations in the wind turbines' (WT) output power caused by wind speed variations; taking into account the filter parameters variations (structural parameter uncertainties).

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1249-1253
• /
• 2004

A robust input modification approach to the control of flexible joint robot is presented. In our previous study, we developed an observer based state feedback control for the suppression of residual vibration of a robot. The control was very effective in suppressing the inherent vibration of a flexible joint robot. However it did not meet high performance requirements under high speed motion and model uncertainties. As a solution of the problem, we present an input modification method with robustness against parametric uncertainties. The main idea of the proposed input modification method is to generate a modified reference position command for fast and accurate motion of the robot. Using this proposed method we can reduce the servo delay and settling time by about 60% and substantially improve the path accuracy.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1172-1175
• /
• 2001

Recently, vector control without a speed sensor for an inverter induction motor system has been developed. In this paper describes the vector control system estimates rotor speed based on FMRAS(Flux Model Reference Adaptive System). Because of improving the initial condition and drift problem by pure integrator is eliminated, we can be expected to rapid responsibility of the speed estimation. The stability of speed estimator is proved on the basis of hyperstability theory. Proposed control system used TMS320C31 DSP for high speed processing. The effectiveness of the proposed system is verified by simulation and experimental results. This result shows that the highly characteristic speed estimation and robust character of load regulation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.6
• /
• pp.502-508
• /
• 2001

In this paper, slack is computed from a comparison of the cable pay out rate and the ship ground speed in accordance with laying conditions, and the speed controller of the cable engine based on an H(sub)$\infty$ servo control id designed for adjusting the cable engine in order to lay a desired amount of slack. The controller is designed for robust tracking of the cable engine under disturbances. The performance of the designed controller is evaluated by computer simulation, and, consequently, a feasibility study for laying the submarine cable stably is done through analyzing simulation results.

• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.18-24
• /
• 2018

This paper focuses on systematic design about the membership ranges of the main design factors such as control error, control error rate, and sampling time for the fuzzy logic control of the variable speed drive refrigeration cycle. The upper and the lowest limit of the membership ranges are set up from the data of static characteristics obtained by experiments. Three kinds of membership ranges on the control error and the control error rate are tested by experiments. Especially, an effect of sampling time on control performance is also investigated in the same way. Experimental data showed the control error rate and the sampling time strongly effected on the control performance of the refrigeration cycle with a variable speed drive.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.1
• /
• pp.18-27
• /
• 2002

This paper presents an implementation of digital high-performance speed sensorless control system of an induction motor drives with Direct Torque Control(DTC). The system consists of closed loop stator flux and torque observer, speed and torque estimators, two hysteresis controllers, an optimal switching look-up table, IGBT voltage source inverter, and TMS320C31 DSP controller board. The stator flux observer is based on the combined current and voltage model with stator flux feedback adaptive control for wide speed range. The speed estimator is using the model reference adaptive system(MRAS) with rotor flux linkages for speed turning signal estimation. In order to prove the suggested speed sensorless control algorithm, and to obtain a high-dynamic robust adaptive performance, we have some simulations and actual experiments at low(20rpm) and high(1000rpm) speed areas. The developed speed sensorless system are shown a good speed control response characteristic, and high performance features using 2.2[kW] general purposed induction motor.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.4
• /
• pp.476-482
• /
• 2010

In this paper, we propose a robust path tracking control method for autonomous underwater vehicle with variable speed. The proposed path tracking controller consists of a kinematic controller and a dynamic controller. First, the kinematic controller computes the surge speed and yaw rate to follow the reference path with variable speed. Then the dynamic controller controls the thrust force and yaw torque to move the AUV actually. In the dynamic control, we assume that the sway speed is a disturbance. In addition the dynamic controller is designed based on sliding mode conrol. We also demonstrate the stability of the proposed control method by Lyapunov stability theory. Finally, simulation results illustrate the performance of the proposed control method.