• International Journal of Highway Engineering
• /
• v.7 no.3 s.25
• /
• pp.79-91
• /
• 2005

The temperature patterns in Portland cement concrete (PCC) pavements were measured and comprehensively analyzed from the beginning of the concrete placement based on the temperature measurement technique developed using innovative and inexpensive temperature measurement sensors. The temperature measurements in PCC pavements were taken at several different locations forvarious slab thicknesses. The concrete temperature patterns in the vertical and longitudinal directions of the pavement were analyzed and the effects of the pavement surface reflectivity, shading, and covering on the concrete temperatures were evaluated. The results of this study showed that the significant differences in the maximum concrete temperatures on the placement day were observed according to the concrete placement time. Since the zero-stress temperature is a function of the maximum concrete temperature on the placement day, the placement time would be an important factor that affects the behavior and performance of concrete pavements. The surface conditions of the pavement, such as the surface color, shading, and covering also affected the temperature patterns in PCC pavements significantly.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.6
• /
• pp.5-21
• /
• 2014

It has been pointed out that the collapses of unsaturated road embankments caused by earthquake are attributed to high water content caused by the seepage of the underground water and/or the rainfall infiltration. Hence, it is important to study influences of water content on the dynamic stability and deformation mode of unsaturated road embankments for development of a proper design scheme including an effective reinforcement to prevent severe damage. This study demonstrates dynamic centrifugal model tests with different water contents to investigate the effect of water content on deformation and failure behaviors of unsaturated road embankments. Based on the measurement of displacement, the pore water pressure and the acceleration during dynamic loading, dynamic behavior of the unsaturated road embankments with about optimum water content and the higher water content than the optimum one have been examined. In addition, an image analysis has revealed the displacement field and the distributions of strains in the road embankment, by which deformation mode of the road embankment with higher water content has been clarified. It has been confirmed that in the case of higher water content the settlement of the crown is large mainly owing to the volume compression underneath the crown, while the small confining pressure at the toe and near the slope surface induces large shear deformation with volume expansion.

• International Journal of Highway Engineering
• /
• v.15 no.2
• /
• pp.11-18
• /
• 2013

PURPOSES : This study presents the noise level and frequency characteristics investigated in the national highways with the consideration of various measuring conditions and/or methods. METHODS : The noise levels on the asphalt concrete pavement(ACP) and the jointed plain concrete pavement(JPCP) of the national highway were measured and analysed with respect to three variables, i.e., pavement type, surface condition, and measurement distance. The PASS-By method is utilized for the noise measurement and then using CPB spectrum analysis method with 1/3 octave bandwidth, the noise levels and frequency characteristics were calculated for two-second periods before and after the peak noise. RESULTS : Depending on the pavement type, the noise level was changed as the average noise levels are 73.3dB(A) and 78.3dB(A) for ACP and JPCP, respectively. With respect to the effect of surface condition, the average noise levels for crack H(high), M(medium), and L (low) sections are 77.4dB(A), 77.4dB(A), and 78.1dB(A), respectively. Regarding the measurement distance, 1.2meter difference in measuring location reduces 1.6dB(A) of noise level; the average noise levels at 5.3m and 7.5m from the centerline of outer lane are 72.8dB(A) and 71.2dB(A), respectively. It should be noted that the noise levels are slightly different as a function of vehicle speed and type. However, the overall trends for each case was similar. It was found that the domain frequency bands for ACP and JPCP were 400Hz~2000Hz and 500Hz~2000Hz, respectively. CONCLUSIONS : Based on the analysis with the measured noise date from national highway, it was concluded that the noise level and frequency band vary depending on the various conditions. It was also found that some variables significantly affect the noise level while others do not. With further systematic investigation, the comprehensive noise characteristics on the national highway can be achieved. Using such database, it is possible to develop the fundamental noise reduction technology.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.53-60
• /
• 1998

We develope a high repetition rate, short distance, optical range finder for surface roughness measurements of large structures, such as a highway road, etc. For range measurement based on a triangulation principle, we use a light emitting diode and an one dimensional Position sensitive photodetector for a light source and an angle detector of the reflected light at the object, respectively. The range finder has automatic power control and electrical background noise rejection capabilities which enable it to overcome variations of an object reflectance and to eliminate time-varying, as well as constant, background light noises. Our experimental results show less than ${\pm}1.5mm$ of measurement errors regardless of an object reflectance, for $22{\sim}38cm$ object ranges which are determined by considering the installation of the range finder and the depth of surface roughness.

• Particle and aerosol research
• /
• v.8 no.1
• /
• pp.17-28
• /
• 2012

Air pollution levels of gases and aerosol particles inside the Jeongneung and Hongjimun tunnels of the Naebu express way in Seoul were investigated through on-road measurement using a mobile emission laboratory (MEL) on February 8, 2011. The concentrations of $NO_x$, $CO_2$, number concentration of particles ranging 21-560 nm, and surface area of particles deposited on a human lung almost linearly increased with increasing distance from the tunnel entrance, and decreased rapidly before the tunnel exit. This trend was observed regardless of tunnel length and driving directions, which thought to be caused by semi-transverse ventilation facilities of the tunnels. The concentration increments per 1-m distance for $NO_x$, $CO_2$, deposited particle surface area, and number of particles ranging 21-560 nm were 0.61~0.80 ppb, 0.16~0.21 ppm, $0.20{\sim}0.29{\mu}m^2/cm^3$, and 117~192 particles/$cm^3$, respectively. Average pollution levels inside the two tunnels for $CO_2$, deposited particle surface area, and number of particles >5.6 nm ranged 681~748 ppm, $246{\sim}381{\mu}m^2/cm^3$, and $2.4{\sim}6.7{\times}10^5$ particles/$cm^3$, respectively. In case of $NO_x$, the maximum concentration exceeded 1 ppm. These pollution levels inside the tunnels are much higher than those at urban background sites. This result can be utilized as basic data to evaluate the effectiveness of present ventilation system for reducing the pollution level caused by vehicles inside the tunnels.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.2
• /
• pp.150-156
• /
• 2011

Smart Highway is a next generation highway that significantly improves a traffic safety, reduces incidence of traffic accidents, and supports intelligent and convenient driving environments so that drivers can drive at high speeds in safety. In order to implement smart highway, it is required to gather a large amount of data including conditions of a road and the status of vehicles, and other useful data. To provide situation information of highway, it has been gathered traffic information using optical sensors(CCTV, etc.). However, this technique has problems such as the problem of information gathering, lack of accuracy depending on weather conditions and limitation of maintenance. It needs radar system which has not effect on environmental change and algorithm processing technique in order to provide information for a safety driving to driver and car. In this paper, it is used radar with 9.4GHz to test performance of a road surface and developed radar system for detecting test. And we compared and analyzed a performance of data acquired from each radar through computer simulation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.11
• /
• pp.1043-1050
• /
• 2011

This paper presents practical results for the estimation of vibration level inside a powertrain based on the rigid body theory and measurement. The vibration level of inside powertrain has been used for the calculation of excitation force of an engine indirectly. However it was difficult to estimate or measure the vibration level inside of a powertrain when a powertrain works on the driving condition of a vehicle. To do this work, the rigid body theory is employed. At the first, the vibration on the surface of a powertrain is measured and its results are secondly used for the estimation the vibration level inside of powertrain together with rigid body theory. Also did research on how to decrease the error rate when the rigid body theory is applied. This method is successfully applied to the estimation of the vibration level on arbitrary point of powertrain on the driving condition at the road.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.5
• /
• pp.47-52
• /
• 2011

We studied about the damaged tire decision algorithm that measured dominant period of ultrasonic signal due to a foreign material on the friction between tire and road surface. We computed the power spectrum about the envelope of ultrasonic signal acquired from the damaged tire, then proposed the dominant period decision algorithm by statistical power threshold value. As the result of simulation, when driving by the speed of 80km/h, the 100ms of dominant period that measured in the proposed algorithm is more accurate than the 97.6ms of power spectrum peak period referenced on the average period of ultrasonic signal envelope peak, 101.24ms.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2351-2353
• /
• 2005

본 논문은 포장도로의 표면 상태를 고성능의 레이저 변위 센서를 사용하여 정밀하게 측정하고, GPS(Global Positioning System)를 사용하여 측정 위치 데이터를 획득하는 도로 표면 측정 장비 개발에 관한 논문이다. 본 연구에서는 전체 시스템을 설계하고, 차량 주행을 모사한 실험 모형을 제작하여 실내 실험을 실시하였으며, GPS 단말기로부터 실시간으로 위치 신호를 수신하여 도로면 데이터와 연동할 수 있도록 하였다. 그리고 평가 차량의 전면에 레일(rail)을 장착하여 레이저 변위 센서가 좌우로 왕복운동이 가능하도록 하였으며, 레일을 작동시킨 상태에서 도로면을 측정해 보았다. 실험 모형의 측정 곁과는 차량이 80km/h로 주행할 때 도로 표지 타이닝(tinning)의 폭 오차 3.24%, 깊이 오차 5%였다. 차량이 정지된 상태에서 레일을 작동시켜 요철을 측정하였을 경우 레일 방향에 대한 폭 오차는 0.07%였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1150-1155
• /
• 2001

Vehicle Manufacturers use asphalt deadener sheets for their passenger cars to reduce noise and vibration from engine and road surface. Since their shapes are limited to a few variations, it is very difficult to reduce unnecessary weight by changing the shape of the deadeners. There is also damping performance limit in the asphalt sheets. Therefore, a high damping material should be implemented into the vehicle noise and vibration reduction activities to overcome the disadvantage of asphalt sheets. In this study, measurement of the damping loss factor and sound transmission loss were made to compare the properties and vehicle test and analysis was followed to evaluate the NVH performance of each deadener type in the vehicle.