• Structural Engineering and Mechanics
• /
• v.83 no.1
• /
• pp.123-134
• /
• 2022

The stability of cable-stayed bridges is an important factor considered during design. In recent years, the novel spatial diamond-shaped bridge pylon has shown its advantages in various aspects, including the static response and the stability performance with the development of cable-stayed bridge towards long-span and heavy-load. Based on the energy approach, this paper presents a practical calculation method of the completed state stability of a cable-stayed bridge with two spatial diamond-shaped pylons. In the analysis, the possible transverse buckling of the girder, the top pylon column, and the mid pylon columns are considered simultaneously. The total potential energy of the spatial diamond-shaped pylon cable-stayed bridge is calculated. And based on the principle of stationary potential energy, the transverse buckling coefficients and corresponding buckling modes are obtained. Furthermore, an example is calculated using the design parameters of the Changtai Yangtze River Bridge, a 1176 m cable-stayed bridge under construction in China, to verify the effectiveness and accuracy of the proposed method in practical engineering. The critical loads and the buckling modes derived by the proposed method are in good agreement with the results of the finite element method. Finally, cable-stayed bridges varying pylon and girder stiffness ratios and pylon geometric dimensions are calculated to discuss the applicability and advantages of the proposed method. And a further discussion on the degrees of the polynomial functions when assuming buckling modes are presented.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5B
• /
• pp.501-509
• /
• 2006

The safety of levee that depends on the river flood elevation has been regarded as very important keys to build up various flood prevention systems. However, deterministic methods for computation of water surface profile cannot reflect the effect of possible inaccuracies in the input parameters. The purpose of this study is to develop a methodology of uncertainty computation of design flood level based on steady flow analysis and Monte Carlo simulation. This study addresses the uncertainty of water surface elevation by Manning's coefficients, design discharges, river cross sections and boundary condition. Monte Carlo simulation with the variations of these parameters is performed to quantify the variations of water surface elevations in a river. The proposed model has been applied to the Kumho-river. The reliability analysis was performed within 38.5 km (95 sections) reach considered the variations of the above-mentioned parameters. Overtopping risks were evaluated by comparing the elevations of the flood condition with the those of the levees. The results show that there is a necessity which will raise the levee elevation between 1 cm and 56 cm at 7 sections. The model can be used for preparing flood risk maps, flood forecasting systems and establishing flood disaster mitigation plans as well as complement of conventional levee design.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.35 no.3
• /
• pp.100-116
• /
• 1993

It is experienced fact that unreasonable design criterion and unsitable operation management for the agricultural structures including reservoirs based on short terms data of monthly flows have been brought about not only loss of lives, but also enormous property damage. For the solution of this point at issue, this study was conducted to simulate long series of synthetic monthly flows by multi-season first order Markov model with selection of best fitting frequency distribution and to make a comparison of statistical parameters between observed and synthetic flows of six watersheds in Yeong San and Seom Jin river systems. The results obtained through this study can be summarized as follows. 1.Both Gamma and two parameter lognormal distribution were found to be suitable ones for monthly flows in all watersheds by Kolmogorov-Smirnov test while those distributions were judged to be unfitness in Nam Pyeong of Yeong San and Song Jeong and Ab Rog watersheds of Seom Jin river systems in the $\chi$$^2$ goodness of fit test. 2.Most of the arithmetic mean values for synthetic monthly flows simulated by Gamma distribution are much closer to the results of the observed data than those of two parameter lognomal distribution in the applied watersheds. 3.Fluctuation for the coefficient of variation derived by Gamma distribution was shown in general as better agreement with the results of the observed data than that of two parameter lognormal distribution in the applied watersheds both in Yeong San and Seom Jin river systems. Especially, coefficients of variation calculated by Gamma distribution are seemed to be much closer to those of the observed data during July and August. 4.It can be concluded that synthetic monthly flows simulated by Gamma distribution are seemed to be much closer to the observed data than those by two parameter lognormal distribution in the applied watersheds. 5.It is to be desired that multi-season first order Markov model based on Gamma distribution which is confirmed as a good fitting one in this study would be compared with Harmonic synthetic model as a continuation follows.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.143-145
• /
• 2021

The Sihwa River was first planned to be a fresh water lake, but it failed due to serious environment pollution. During times of destruction and regeneration, changes of ecosystem of Sihwa River was visible, especially the algal ecosystem. It's because many seasonal birds pass through the place. This paper analyzes the changes of algal ecosystem of Sihwa River based on eight ecosystem indices. Moreover, using gradient descent, COD is expressed has a function of three ecosystem indices selected from above which is newly defined as SEI, Sihwa Ecosystem Index. In conclusion, we can observe the current ecosystem more easily without its actual data, but only with informations of the ecosystem.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.481-487
• /
• 2020

This study examined the behavior change of river levees during an earthquake by numerical analysis. Unlike conventional research using artificial earthquake waves, earthquake analysis was performed using real earthquake waves. The behavior of a river levee before and after an earthquake was compared and analyzed quantitatively. Studies show that the river levee has a safety factor of approximately 28.5% due to an earthquake. On the other hand, the minimum standard safety factor is satisfied. Vertical effective stress has decreased by 81.8% due to excess pore-water pressure generated by the earthquake. In addition, liquefaction occurs in most of the foundation soil. An examination of the stress-displacement behavior due to the earthquake revealed a large amount of settlement in the backfill layer. Most of the foundation soil yielded. Therefore, the target river levee is quite vulnerable to earthquakes. Through the results of this study, the necessity of refreshing the seismic design standards for river levees is required. This study can be used as basic data for estimating the approximate damage level and vulnerable areas.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.3
• /
• pp.61-75
• /
• 2007

Deep foundations have been popularly installed in hard stratum such as gravels or rocks in Korea. However, it is necessary to consider sand or sandy gravel layers that locate at the mid-depths as the bearing stratum of piles in the thick Nakdong River deltaic deposits, as done in the Chaophraya (Bangkok) and Mississippi River deltas. This study was focused on the finding of suitable methods for estimating bearing capacity when driving prestressed high-strength concrete (PHC) piles to a required depth in the deltaic area. Ground investigation was performed at five locations of two sites in the deltaic area. Bearing capacity of the driven piles has been computed using a number of proposed methods such as CPT-based and other analytical methods, based on the ground investigation and comparison one another other. Five PDA (pile driving analyzer) tests were systematically carried out at the whole depths of embedded piles, which is a well-blown useful technique for the purposes. As the results, the bearing capacities calculated by various methods were compared with the PDA and static load testing results. It was found that the shaft resistance is significantly governed by set-up effects and then the long-term value agrees well with that of the $\beta$ method. Also, the design methods for toe resistance were determined based on the SLT result, rather than PDA results that led to underestimation. Moreover, using the CPT results, appropriate methods were proposed for calculating the bearing capacity of the piles in the area.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.6 no.4
• /
• pp.122-134
• /
• 2003

In recent, different kinds of nationwide thematic map have been developed based on NGIS, and each related research field has tried to develop GIS by utilizing this map. Also, Many researches on the geographic information data model has been conducted to improve the compatibility of developed system. The developed system in water resource field should reflect the dynamic characteristics of river flow. Because it should be considered from the design of data model, this study suggests the datamodel for designing geographical information database on water resources which is possible to linear reference capacity based on stream network. In order to examine the applicability of the suggested model, network component based system has developed. Finally, the river network based system shows the superiority in terms of its applicability comparing with other system.

• Computers and Concrete
• /
• v.24 no.5
• /
• pp.459-468
• /
• 2019

The stability and safety of concrete plug structure of diversion tunnel is crucial for the impoundment of upstream reservoir in hydropower projects. The ongoing Wudongde hydropower plant in China plans to adopt straight column plugs and curved column plugs to replace the traditional expanded wedge-shaped plugs. The performance of the proposed new plug structures under high water head is then a critical issue and attracts the attentions of engineers. This paper firstly studied the joint bearing mechanism of plug and surrounding rock mass and found that the quality and mechanical properties of the interfaces among plug concrete, shotcrete, and surrounding rock mass play a key role in the performance of plug structures. By performing geophysical and mechanical experiments, the contact state and the mechanical parameters of the interfaces were analyzed in detail and provide numerical analysis with rational input parameters. The safety evaluation is carried out through numerical calculation of plug stability under both construction and operation period. The results indicate that the allowable water head acting on columnar plugs is 3.1 to 7.4 times of the designed water head. So the stability of the new plug structure meets the design code requirement. Based on above findings, it is concluded that for the studied project, it is feasible to adopt columnar plugs to replace the traditional expanded wedge-shaped plugs. It is hoped that this study can provide reference for other projects with similar engineering background and problems.

• Structural Engineering and Mechanics
• /
• v.57 no.6
• /
• pp.1085-1105
• /
• 2016

The drainage problem in bifurcations causes pecuniary losses when hydropower stations are undergoing periodic overhaul. A new design philosophy for Y-typed bifurcations that are flat-bottomed is proposed. The bottoms of all pipe sections are located at the same level, making drainage due to gravity possible and shortening the draining time. All fundamental curves were determined, and contrastive analysis with a crescent-rib reinforced bifurcation in an actual project was conducted. Feasibility demonstrations were researched including structural characteristics based on finite element modeling and hydraulic characteristics based on computational fluid dynamics. The new bifurcation provided a well-balanced shape and reasonable stress state. It did not worsen the flow characteristics, and the head loss was considered acceptable. The proposed Y-typed bifurcation was shown to be suitable for pumped storage power stations.

• Steel and Composite Structures
• /
• v.42 no.4
• /
• pp.489-499
• /
• 2022

This paper proposes a numerical optimization method to design the mesoscale architecture of textile composite for simultaneously enhancing mechanical and thermal properties, which compete with each other making it difficult to design intuitively. The base cell of the periodic warp and fill yarn system is served as the design space, and optimal fibre yarn geometries are found by solving the optimization problem through the proposed method. With the help of homogenization method, analytical formulae for the effective material properties as functions of the geometry parameters of plain-woven textile composites were derived, and they are used to form the inverse homogenization method to establish the design problem. These modules are then put together to form a multiobjective optimization problem, which is formulated in such a way that the optimal design depends on the weight factors predetermined by the user based on the stiffness and thermal terms in the objective function. Numerical examples illustrate that the developed method can achieve reasonable designs in terms of fibre yarn paths and geometries.