• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.5
• /
• pp.72-84
• /
• 1998

In order ot study the influence of a circular inclusion on a stress field near a crack tip, mutual interference of a slant crack and the circular inclusion is analyzed of a bimaterial inclusion. As the crack emanates at the equivalent slant crack angle the correction factors FⅠ and FⅡ for the inclusion wit small Young's modulus were found to decrease as the inclusion radius increased. The correction factors for inclusion with large Young's modulus increase as the inclusion radius increases at the equivalent radius of the inclusion, the correction factors decrease as the slant crack angle increases for the aspect ratio $\frac{c}{W}$ = 0.1 irrespective of the Young's modulus. For $\frac{c}{W}$ greater than 0.2, they increase as the slant crack angle increases. There is no influence of stress mutual interfce after crack emanates beyond the inclusion radius.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.11 s.170
• /
• pp.2078-2086
• /
• 1999

Fracture behaviors of an interface crack in a ductile layer sandwiched by rigid substrates are analyzed by finite element method. Several fracture mechanisms and the corresponding criteria are examined. And the crack growth behavior and fracture toughness are predicted. As the results, various crack growth procedures such as the crack jump to the other interface on the opposite side, the creation of a new crack far from the initial crack front, and the asymmetric relation of fracture toughness vs. mode mixity ($J_c$-$\Phi$) can be successfully explained.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4A
• /
• pp.353-359
• /
• 2010

Cementitious matrix based composites are vulnerable to the drying shrinkage crack during the curing process. In this study, the drying shrinkage induced fracture behavior of the fiber reinforced concrete is simulated and the effects of the fiber reinforcement conditions on the fracture characteristics are analysed. The numerical model is composed of conduit elements and rigid-body-spring elements on the identical irregular lattice topology, where the drying shrinkage is presented by the coupling of nonmechanical-mechanical behaviors handled by those respective element types. Semi-discrete fiber elements are applied within the rigid-body-spring network to model the fiber reinforcement. The shrinkage parameters are calibrated through the KS F 2424 free drying shrinkage test simulation and comparison of the time-shrinkage strain curves. Next, the KS F 2595 restrained drying shrinkage test is simulated for various fiber volume fractions and the numerical model is verified by comparison of the crack initiating time with the previous experimental results. In addition, the drying shrinkage cracking phenomenon is analysed with change in the length and the surface shape of the fibers, the measurement of the maximum crack width in the numerical experiment indicates the judgement of the crack controlling effect.

• Geomechanics and Engineering
• /
• v.22 no.4
• /
• pp.319-328
• /
• 2020

This paper investigates the effect of the width of failure and tension crack (TC) on the stability of cohesive-frictional soil slopes in three dimensions. Working analytically, the slip surface and the tension crack are considered to have spheroid and cylindrical shape respectively, although the case of tension crack having planar, vertical surface is also discussed; the latter was found to return higher safety factor values. Because at the initiation of a purely rotational slide along a spheroid surface no shear forces develop inside the failure mass, the rigid body concept is conveniently used; in this respect, the validity of the rigid body concept is discussed, whilst it is supported by comparison examples. Stability tables are given for fully drained and fully saturated slopes without TC, with non-filled TC as well as with fully-filled TC. Among the main findings is that, the width of failure corresponding to the minimum safety factor value is not always infinite, but it is affected by the triggering factor for failure (e.g., water acting as pore pressures and/or as hydrostatic force in the TC). More specifically, it was found that, when a slope is near its limit equilibrium and under the influence of a triggering factor, the minimum safety factor value corresponds to a near spherical failure mechanism, even if the triggering factor (e.g., pore-water pressures) acts uniformly along the third dimension. Moreover, it was found that, the effect of tension crack is much greater when the stability of slopes is studied in three dimensions; indeed, safety factor values comparable to the 2D case are obtained.

• Computers and Concrete
• /
• v.7 no.4
• /
• pp.331-346
• /
• 2010

We present a quadrilateral finite element with an embedded crack that can be used to model tensile fracture in two-dimensional concrete solids and the crack growth. The element has kinematics that can represent linear jumps in both normal and tangential displacements along the crack line. The cohesive law in the crack is based on rigid-plasticity with softening. The required material data for the concrete failure analysis are the constants of isotropic elasticity and the mode I softening curve. The results of two well known tests are presented in order to illustrate very satisfying performance of the presented approach to simulate failure of concrete solids.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.3 no.3
• /
• pp.139-147
• /
• 1999

Six reinforced concrete shear wall, constructured with fully rigid, slit, and infilled types, were tested under both vertical and cyclic loadings. Experimental programs were carried out to evaluate the seismic performance of such test specimens, such as the hysteretic behavior, the maximum horizontal strength, crack propagation, and ductility, under load reversals. All the specimens were modeled in one-third scale size. Based on the test results, the following conclusions can be made. For the diagonal reinforced slit and infilled shear wall specimens, it was found that the failure mode shows very effective crack control and crushing due to slippage prevention of boundary region and reduction of diagonal tension rathar than the brittle shear and diagonal tension failure. The ductility of specimens designed by the diagonal reinforcement for the slit and infilled shear wall was increased 1.72~1.81 times in comparison with the fully rigid shear wall frame. Maximum horizontal load-carrying capacity of specimens designed by the diagonal reinforcement ratio the slit and infilled shear wall was increased respectively by l.14 times and l.49 times in comparison with the standard fully rigid shear wall frame.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.04a
• /
• pp.683-688
• /
• 1999

The purpose of this study is to develop and evaluate the structural performance of various shear walls, such as the hysteretic behavior, the maximum horizontal strength, crack propagation, and ductility etc. under load reversals. For the diagonal reinforced slit and infilled shear wall specimens, it was found that the failure mode shows very effective crack control and crashing due to slippage prevention of boundary region and reduction of diagonal tension rather than the brittle shear and diagonal tension failure. The ductility of specimens designed by the diagonal reinforcement for the slit and infilled shear wall was increased 1.72~1.81 times in comparison with the fully rigid shear wall frame. Maximum horizontal load-carrying capacity of specimens designed by the diagonal reinforcement ratio the slit and infilled shear wall was increased respectively by 1.14 times and 1.49 times in comparison with the standard fully rigid shear wall frame.

• Computational Structural Engineering
• /
• v.7 no.2
• /
• pp.111-120
• /
• 1994

Cracks in rubber bonded to a rigid material such as steel are analyzed with the aid of a mixed finite element technique. Firstly the weak form is derived for finite element analysis of an incompressible material, and the Mooney-Rivlin form is assumed for the constitutive modeling of rubber. The numerical results from finite element analysis is examined to confirm the accuracy and convergence of solution by way of comparison to other numerical results. The interpretation of the J-integral for large elastic deformation as the energy release rate is confirmed, and the J-integral is calculated for varing crack length. The crack growth stability is discussed using the result of finite element analysis.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.7
• /
• pp.1255-1265
• /
• 1992

Under uniform heat flow, the thermal stress intensity factors for the interfacial crack on a rigid cusp-type inclusion are determined by Hilbert problem expressed with complex variable. The thermal stress intensity factors are expressed in terms of the periodic function of heat flow angle. When the tip of the interfacial crack meets that of the cusp crack, the thermal stress intensity factors have singularities. The thermal stress intensity factors at the interfacial crack tip located in the distance from the cusp crack tip vary with the location of the interfacial crack tip. From the results of the analysis, the complex potential functions and the thermal stress intensity factors for the cusp-type inclusion without the interfacial crack are derived under the cusp surface boundary conditions insulated or fixed to zero relative temperature.

• Structural Engineering and Mechanics
• /
• v.57 no.6
• /
• pp.1143-1156
• /
• 2016

This paper presents a comparative study of finite element method (FEM) and analytical method for the plane problem of a layered composite containing an internal perpendicular crack in literature. The layered composite consists of two elastic layers having different elastic constants and heights. External load is applied to the upper elastic layer by means o a rigid punch and the lower elastic layer rests on two simple supports. Numerical simulations are realized by the world wide code ANYS software. Two dimensional analysis of the problem is carried out and the results are verified by comparison with solutions reported in literature. Main goal of the numerical simulation is to investigate the normal stress ${\sigma}_x$(0, y), stress intensity factors at the crack factor and the crack opening displacements.