• Earthquakes and Structures
• /
• 제19권2호
• /
• pp.103-117
• /
• 2020

The effect of the foundation size on the efficiency of seismic base isolation using a layer of stone pebbles is experimentally investigated. Four scaled models of buildings with different stiffnesses (from very stiff to soft) were tested, each with the so-called small and large foundation, and exposed to four different accelerograms (different predominant periods and durations). Tests were conducted so that the strains in the model remained elastic and afterwards the models were tested until collapse. Each model was tested for the case of the foundation being supported on a rigid base and on an aseismic layer. Compared to the smaller foundation, the larger foundation results in a reduced rocking effect, higher earthquake forces and lower bearing capacity of the tested models, with respectable efficiency (reduced strain/stress, displacement and increase of the ultimate bearing capacity of the model) for the considered seismic base isolation compared to the foundation on a rigid base.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.117-121
• /
• 2005

In this paper, an approximate time-effective approach to rigid-plastic finite element method is presented with its solution scheme and a volume compensation method is proposed to simulate rotary forging processes. The applicability is examined by comparing the results obtained by the presented approach with those by the conventional approach. The approach is applied to simulation of a rotary forging process fur a wheel bearing assembly. The analyzed results are compared with the experimental results.

• Journal of Mechanical Science and Technology
• /
• 제16권12호
• /
• pp.1583-1593
• /
• 2002

This paper discusses the model validation and vibration suppression of an AMB flexible rotor via additional LQG controller. The main difficulty in the vibration suppression of the flexible rotor using AMB is to realize a controller that can minimize resonance without injuring the stabilized rigid modes. In order to solve this problem, simple scheme for system modeling and controller design are developed. Firstly, the AMB flexible rotor is stabilized with a PID controller, which leads to a new stable rotor-bearing system. Then, authors propose the model validation procedure using measured open-loop frequency responses to obtain an accurate model of the AMB flexible rotor system. After that, LQG controller with modal weighting is designed to suppress resonances of the stable rotor-bearing system. Due to the poor controllability and observability of flexible modes compared to rigid ones, balancing of two Gramians is prerequisite for the fair LQG controller design. Simulation with step disturbance and experimental results of unbalance response up to 10,000 rpm verified the effectiveness of the proposed scheme.

• Safety and Health at Work
• /
• 제10권3호
• /
• pp.314-320
• /
• 2019

Background: Sitting posture may be related to risk factors, including inadequate weight-bearing support, particularly when maintained for long periods. Considering that body weight is loaded in a closed support system composed of the seat, backrest, floor and working surface, the aims of the present study were to describe the development of an ergonomic sitting workstation to continuously record weight-bearing at the seat, chair, backrest, work surface, and floor and to test its measurement properties: reproducibility, criterion-related validity, and sensitivity. Methods: Rigid bodies (1 to 30 kg) and participant weights were recorded to evaluate the workstation measurement properties. Results: Rigid body tests showed variation values less than 0.050 kg on reproducibility test and errors below 5% of measured value on criterion validity tests. Participant tests showed no statistically significant differences between repeated measures ($p{\geq}0.40$), errors were less than 2% of participant weights an sensitivity presented statistically significant changes (p = 0.007). Conclusion: The sitting workstation proposed showed to be reliable, valid and sensitive for use in future ergonomic studies to evaluate the sitting posture.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.119-128
• /
• 1998

In this paper, nonsteady state shaped drawing process has been investigated using the three-dimensional rigid-plastic finite element method. In order to analyze the shaped drawing process, a method to define straight converging die considering straight die part, die radius part and bearing part has been proposed. In addition, the modeling of initial billet and the generation procedure of mesh system have been suggested. The three-dimensional rigid-plastic finite element simulation has been performed for a square sectional drawing process and its result has been confirmed in comparison with the existing experimental one. Also, for the same process conditions, the effect of perimeter ratio in the shaped drawing process has been investigated.

• Tribology and Lubricants
• /
• 제6권1호
• /
• pp.74-81
• /
• 1990

The threshold of instability for a rigid rotor supported in externally pressurized airlubricated circular or non-circular journal bearings of finite length is theoretically analyzed. The analysis is performed for a bearing having one feeding plane, no recess volume, which is assumed to be a line source, and is based on a first order perturbation of journal center motion about steady state position. And then linearized system dynamic analysis is carried out. Numerical results are given, showing the threshold of instability as a function of supply pressure ratio, feeding parameter and load. It is shown that the region that 2-lobe bearing is more stable than circular bearing exists and whirl ratio of 2-lobe bearing is less than that of the other types of bearing.

• 한국소음진동공학회논문집
• /
• 제14권11호
• /
• pp.1059-1065
• /
• 2004

In this paper, the dynamic characteristic analysis of carriage structure supported by air bearings were performed. Toward this end, the characteristics of air bearing were numerically analyzed to estimate the stiffness of the air bearing and the clearance between air bearing and guide surface. The modal analysis of the carriage structure was performed by using finite element method, and the experimental modal analysis was also performed to validate the finite element model, where rigid body modes were compared to validate the stiffness of the air bearings. From the results, the air spring stiffness can be estimated within the range of acceptable accuracy under any pressure and clearance condition.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.1107-1114
• /
• 2003

In this thesis, the dynamic characteristic analysis of carriage structure supported by air bearings were peformed. Toward this end, the characteristics of air bearing were numerically analyzed to estimate the stiffness of the air bearing and the clearance between air bearing and guide surface. The modal analysis of the carriage structure was peformed by using finite element method, and the experimental modal analysis was also performed to validate the finite element model, where rigid body modes were compared to validate the stiffness of the air bearings. From the results, the air spring stiffness can be estimated within the range of acceptable accuracy under any pressure and clearance condition.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 추계학술대회 논문집
• /
• pp.77-78
• /
• 2007

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.35-45
• /
• 1994

The thermohydrodynamic analysis of tilting pad thrust bearing is studied with the consideration of elastic effect of pad. Reynolds equation, deflection equation and energy equation are solved simultaneously with the boundary conditions. Reynolds equation is modified as the approximate form. Pads are supported by the line pivot and the point pivot respectively. Pads are considered as the flat planes. Effects of pad thickness on the performance of thrust bearing are emphasized and the performances of rigid pad and elastic pad are compared. Effects of inlet temperature on performances of the bearing are compared. Dynamic characteristics of both pad supported by line and point pivot are compared.