• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.4
• /
• pp.49-53
• /
• 2022

In this study, quantum dot light-emitting diodes (QLEDs) of the optimized EL performance with a radio frequency (RF) sputtered Zn_0.85Mg_0.15O thin film as an electron transport layer (ETL). In typical QLEDs, ZnO nanoparticles (NPs) are widely used materials for ETL layer due to their advantages of high electron mobility, suitable energy level and easy capable of solution processing. However, the instability problem of solution-type ZnO NPs has not yet been resolved. To solve this problem, ZnMgO thin film doped with 15% Mg of ZnO was fabricated by RF sputtering and optimized for the device applied as an ETL. The QLEDs of optimized ZnMgO thin film exhibited a maximum luminance of 15,972 cd/m² and a current efficiency of 7.9 cd/A. Efficient QLEDs using sputtering ZnMgO thin film show the promising results for the future display technology.

• The Korean Journal of Ceramics
• /
• v.7 no.1
• /
• pp.26-29
• /
• 2001

Indium tin oxide (ITO) films were deposited on glass substrates at $300^{\circ}C$ in oxygen/argon mixtures by RF-enhanced DC-magnetron sputtering and were compared to those by conventional DC magnetron sputtering. The RF enhancement was performed using a coil above an ITO target. X-ray diffraction measurements revealed that RF-enhanced plasma affected the preferred orientation and the crystallinity of the films. The resistivity of the films prepared by RF-enhanced DC-magnetron sputtering was almost constant at oxygen content lower than 0.3% and then increased sharply with increasing oxygen content. However the resistivity of the films by conventional sputtering has little dependence on the oxygen content. Those results can be explained on the basis of the incorporation of oxygen into the ITO films due to the RF enhancement.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.5
• /
• pp.215-219
• /
• 2004

ZnO epitaxial films have been grown on a (0001)sapphire substrate by RF magnetron sputtering. The single crystalline ZnO films were grown at the condition of growth rate of about 0.1~0.2 $\mu\textrm{m}$/hr and the substrate temperature of $600^{\circ}C$. The film thickness was about 400~500 nm. The thin film quality and micro-structure have been evaluated by XRD and TEM observation.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.1
• /
• pp.41-45
• /
• 2013

IGZO transparent conductive thin films were widely used as transparent electrode of optoelectronic devices. We have studied the optical and electrical properties of IGZO thin films. The IGZO thin films were deposited on the corning 1737 glass by RF magnetron sputtering method. The RF power in sputtering process was varied as 25, 50, 75and 100 W, respectively. All of the thin films transmittance in the visible range was above 85%. XRD analysis showed that amorphous structure of the thin films without any peak. The thin films were electrically characterized by high mobility above $13.4cm^2/V{\cdot}s$, $7.0{\times}10^{19}cm^{-3}$ high carrier concentration and $6{\times}10^{-3}{\Omega}-cm$ low resistivity. By the studies we found that IGZO transparent thin film can be used as transparent electrodes in electronic devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.49-52
• /
• 2003

The role of gas ratio with the crystallization behavior and electrical properties in $Bi_{3.25}La_{0.75}Ti_3O_{12}$(BLT) thin films by rf magnetron sputtering method has not been precisely defined. In this work, the ferroelectric properties of these films with gas variation was investigated. BLT thin films were deposited on the Pt/Ti bottom electrode by rf magnetron sputtering method and then they were crystallized by rapid thermal annealing (RTA). The experiment showed that all BLT films indicated perovskite polycrystalline structure with preferred orientation (020) and (0012). And no pyrochlore phase was observed. The fabricated film annealed with $O_2$ of 15 sccm showed that value of leakage current was $9.67{\times}10^{-7}A/cm^2$ at 50kV /em, and the value of remanent polarization (2Pr=Pr+-Pr-) was $11.8{\mu}C/cm^2$. Therefore we induce access to memory device application by rf-magnetron sputtering method in this report.

• Korean Journal of Materials Research
• /
• v.4 no.4
• /
• pp.453-458
• /
• 1994

$(Ba_{0.5}Sr_{0.5)/TiO_3$(BST) thin films were prepared for the application of 256 Mb DRAM by RF magnetron sputtering. The crystallinity of BST thin films increased with increasing deposition tempera lure. The composition of thin films was $(Ba_{0.48}Sr_{0.48)/TiO_{2.93}$ Pt/Ti barrier layer suppressed the diffusion of Si into BST layer. The films showed a dielectric constant of 320 and a dissipation factor of 0.022 at 100 kHz. the change of capacitance of the films with applied voltage was small, showing paraelectric property. The charge storage density and leakage current density were 40fC/$\mu \textrm{m}^{2}$ and 0.8$\mu A/\textrm{cm}^2$, respectively at a field of 0.15 MV/cm. The BST films obtained by RF magnetron sputtering appeared to be potential thin film capacitors for 256 Mb DRAM application.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.4
• /
• pp.36-40
• /
• 2016

The 2 wt.% Al-doped ZnO(AZO) thin films were fabricated on PET substrates with various RF power 20, 35, 50, 65, and 80W by using RF magnetron sputtering in order to investigate the structure, electrical and optical properties of AZO thin films in this study. The XRD measurements showed that AZO films exhibit c-axis orientation. At a RF power of 80W, the AZO films showed the highest (002) diffraction peak with a FWHM of 0.42. At a RF power of 65W, the lowest electrical resistivity was about $1.64{\times}[10]$ ^(-4) ${\Omega}-cm$ and the average transmittance of all films including substrates was over 80% in visible range. Good transparence and conducting properties were obtained due to RF power control. The obtained results indicate that it is acceptable for applications as transparent conductive electrodes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.51-54
• /
• 2000

In this paper, $Ba_{0.5}$Sr$_{0.5}$TiO$_3$ thin films were prepared on Pt/Ti/SiO$_2$/Si substrate by RF magnetron sputtering method. We investigated effect of deposition conditions (especially RF input power) on structural properties of BST thin films. Deposit conditions of BST films were set working gas ratio, Ar:O$_2$= 70 : 30, working pressure 10mTorr, and RF input power 25W, 50W, 75W and 100W. Post-annealing using rapid thermal annealing(RTA) performed at 45$0^{\circ}C$, 55$0^{\circ}C$, $650^{\circ}C$, and 75$0^{\circ}C$ in oxigen ambient for 60 sec, respectively. The structural properties of BST films on Pt/Ti/SiO$_2$/Si substrate analysed by X-ray diffraction(XRD).).).

• Journal of the Korean Vacuum Society
• /
• v.11 no.1
• /
• pp.1-7
• /
• 2002

We deposited $Ba_{0.5}Sr_{0.5}TiO_3$(BST) thin-films on Pt/Ti/$SiO_2$/Si substrates using RF magnetron sputtering method. A Substrate temperature was fixed at room temperature, while working gas flow ratio and RF Power were changed from 90:10 to 60:40 and 50 W, 75 W respectively. Also after BST thin films were deposited, we performed annealing in oxygen atmosphere using Rapid Thermal Annealing. For capacitor application we deposited Pt using E-beam evaporator of UHV system. In a structural property study through XRD measurement we found that crystallization depends on annealing rather than working gas ratio or and RF Power. Electrical properties showed relatively superior characteristic on the annealed sample with 50 W of RF Power.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.3
• /
• pp.143-148
• /
• 2009

We have fabricated Ti metal films on Cu wire substrates by using a RF magnetron sputtering method at different RF powers (0, 30 and 60 W) in a high vacuum, and we have investigated the thin film characteristics and resistivity. The ion bombardment effect is increased by the method to superimpose RF power to DC power applied to two poles of the base; thus, the thin film is deposited at sputtering gas pressures below 1 Pa. Moreover, the thin film formation of the multilayer structure becomes possible by gradually injecting the RF power, and the thin film quality is improved.