• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.330-332
• /
• 2009

Highly stable bottom gate thin film transistors(TFTs) with a zinc indium tin oxide(Zn-In-Sn-O:ZITO) channel layer have been fabricated by rf-magnetron co-sputtering using a indium tin oxide(ITO:90/10), a tin oxide and a zinc oxide targets. The ZITO TFT (W/L=$40{\mu}m/20{\mu}m$) has a mobility of 24.6 $cm^2$/V.s, a subthreshold swing of 0.12V/dec., a turn-on voltage of -0.4V and an on/off ratio of >$10^9$. When gate field of $1.8{\times}10^5$ V/cm was applied with source-drain current of $3{\mu}A$ at $60^{\circ}C$, the threshold voltage shift was ~0.18 V after 135 hours. We fabricated AM-OLED driven by highly stable bottom gate Zn-In-Sn-O TFT array.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.9
• /
• pp.807-811
• /
• 2003

We investigated the electrical characterisitics of T $a_2$ $O_{5}$ (tantalum pentoxide) film and Ti-O/T $a_2$ $O_{5}$ film deposited on $Al_2$ $O_3$based substrate. Ta (tantalum) electrode and $Al_2$ $O_3$ substrate was used for the purpose of simplifying the manufacturing process in IPD's (integrated passive devices). Dielectric materials (T $a_2$ $O_{5}$ and Ti-O/T $a_2$ $O_{5}$ films) deposited on Ta/Ti/A $l_2$ $O_3$ were annealed at 700 $^{\circ}C$ for 60 sec. in vacuum. The XRD results showed that as-deposited T $a_2$ $O_{5}$ film possessed amorphous structure, which was transformed to crystallines by rapid thermal heat treatment. We compared the lnJ- $E^{{\frac}{1}{2}}$, C-V, C-F of both as-deposited and annealed dielectric thin films deposited on Ta bottom electrode. From this results, we concluded that the leakage current could be reduced by introducing Ti-O buffer layer and conduction mechanisms of T $a_2$ $O_{5}$ and Ti-O/T $a_2$ $O_{5}$ could be interpreted appropriately by Schottky emission effect.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.469-472
• /
• 1999

CeO$_2$ thin films have used in wide applications such as SOI, buffer layer, antirflection coating, and gate dielectric layer. CeO$_2$takes one of the cubic system of fluorite structure and shows similar lattice constant (a=0.541nm) to silicon (a=0.543nm). We investigated CeO$_2$films as buffer layer material for nonvolatile memory device application of a single transistor. Aiming at the single transistor FRAM device with a gate region configuration of PZT/CeO$_2$ /P-Si , this paper focused on CeO$_2$-Si interface properties. CeO$_2$ films were grown on P-type Si(100) substrates by 13.56MHz RF magnetron sputtering system using a 2 inch Ce metal target. To characterize the CeO$_2$ films, we employed an XRD, AFM, C-V, and I-V for structural, surface morphological, and electrical property investigations, respectively. This paper demonstrates the best lattice mismatch as low as 0.2 % and average surface roughness down to 6.8 $\AA$. MIS structure of CeO$_2$ shows that breakdown electric field of 1.2 MV/cm, dielectric constant around 13.6 at growth temperature of 200 $^{\circ}C$, and interface state densities as low as 1.84$\times$10$^{11}$ cm $^{-1}$ eV$^{-1}$ . We probes the material properties of CeO$_2$ films for a buffer layer of FRAM applications.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.53-54
• /
• 2006

Arsenic doped p-type ZnO thin films have been realized on intrinsic (100) GaAs substrate by RF magnetron sputtering and thermal annealing treatment. p-Type ZnO exhibits the hole concentration of $9.684{\times}10^{19}cm^3$, resistivity of $2.54{\times}10^{-3}{\Omega}cm$, and mobility of $25.37\;cm^2/Vs$. Photoluminescence (PL) spectra of As doped p-type ZnO thin films reveal neutral acceptor bound exciton ($A^{0}X$) of 3.3437 eV and a transition between free electrons and acceptor levels (FA) of 3.2924 eV. Calculated acceptor binding energy ($E_A$) is about 0.1455 eV. Thermal activation and doping mechanism of this film have been suggested by using X-ray photoelectron spectroscopy (XPS). p-Type formation mechanism of As doped ZnO thin film is more related to the complex model, namely, $As_{Zn}-2V_{Zn}$, in which the As substitutes on the Zn site, rather than simple model, Aso, in which the As substitutes on the O site. ZnO-based p-n junction was fabricated by the deposition of an undoped n-type ZnO layer on an As doped p-type ZnO layer.

• Journal of Information Display
• /
• v.2 no.2
• /
• pp.52-60
• /
• 2001

The electrical and mechanical properties in indium-tin-oxide films deposited on polymer substrate were examined. The materials of substrates were polyethersulfone (PES) which have gas barrier layer and anti-glare coating for plastic-based devices. The experiments were performed by rf-magnetron sputtering using a special instrument and buffer layers. Therefore, we obtained a very flat polymer substrate deposited ITO film and investigated the effects of buffer layers, and the instrument. Moreover, the influences of an oxygen partial pressure and post-deposition annealing in ITO films deposited on polymer substrates were clarified. X-ray diffraction observation, measurement of electrical property, and optical microscope observation were performed for the investigation of micro-structure and electro-mechanical properties, and they indicated that as-deposited ITO thin films are amorphous and become quasi-crystalline after adjusting oxygen partial pressure and thermal annealing above $180^{\circ}C$. As a result, we obtained 20-25 ${\Omega}/sq$ of ITO films with good transmittance (above 80 %) of oxygen contents with under 0.2 % and vacuum annealing. Furthermore, using organic buffer layer, we obtained ITO films which have a rather high electrical resistance (40-45 ${\Omega}/sq$) but have improved optical (more than 85 %) and mechanical characteristics compared to the counterparts. Consequently, a prototype reflective color plastic film LCD was fabricated using the PES polymer substrates to confirm whether the ITO films could be realized in accordance with our experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.303-308
• /
• 2011

The Gallium-doped ZnO(GZO) film deposited at a temperature of $200^{\circ}C$ and a pressure of 10 mtorr has an optical transmittance of 89.0% and a resistivity of $2.0\;m{\Omega}{\cdot}cm$ because of its high crystallinity. Effect of $Al_2O_3$ oxide buffer layers on the optical and electrical properties of sputtered ZnO films were intensively investigated for developing the electrodes of opto-electronic devices which demanded high optical transmittance and low resistivity. The use of $Al_2O_3$ buffer layer could increase optical transmittance of GZO film to 90.7% at a wavelength of 550 nm by controlling optical spectrum. Resistivity of deposited GZO films were much dependent on the deposition condition of $O_2/(Ar+O_2)$ flow rate ratio during the buffer layer deposition. It is considered that the $Al_2O_3$ buffer layer could increase the carrier concentration of the GZO films by doping effect of diffused Al atoms through the rough interface.

• Journal of Magnetics
• /
• v.2 no.3
• /
• pp.76-85
• /
• 1997

Magnetic and magnetostrictive properties of Tb-Fe and Tb-Fe-B thin films are systematically investigated over a wide composition range from 40.2 to 68.1 at. % Tb. The films were fabricated by rf magnetron sputtering using a composite target which consists of an Fe plate and Tb chips. The microstructure, examined by X-ray diffraction, mainly consists of an amorphous phase and, at high Tb contents, a pure Tb phase also exists. A progressive change in the direction of anisotropy from the perpendicular to in-plane occurs as the Tb content increases and the boundary at which the anisotropy change occurs shifts significantly towards to higher Tb contents with the addition of B. The saturation magnetization exhibits maxima at the Tb contents of 42 and 48 at. % for Tb-Fe and Tb-Fe-B thin films, respectively, and it is decreased by the addition of B. The coercive force, measured in the easy direction, decreases monotonically with the Tb content. Excellent magnetostrictive characteristics, particularly at low magnetic fields, are achieved in both Tb-Fe and Tb-Fe-B thin films; for example, a magnetostriction of 138 ppm is obtained in a Tb-Fe-B thin film at a magnetic field as low as 30 Oe. The excellent magnetostrictive properties of the present thin films are supported by the equally excellent magnetic softness, the coercivity below 10 Oe and a typical squared-loop shape with the saturation field as low as 1 kOe. Due to the excellent low field magnetostrictive characteristics, the present Tb-Fe based thin films are thought to be suitable for Si based microdevices.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.615-620
• /
• 2020

Oxide semiconductor, represented by a-IGZO, has been commercialized in the market as active layer of TFTs of display backplanes due to its various advantages over a-Si. a-IGZO can be deposited at room temperature by RF magnetron sputtering process; however, additional thermal annealing above 300℃ is required to obtain good semiconducting properties and stability. These temperature are too high for common flexible substrates like PET, PEN, and PI. In this work, effects of microwave annealing time on IGZO thin film and associated thin-film transistors are demonstrated. As the microwave annealing time increases, the electrical properties of a-IGZO TFT improve to a degree similar to that during thermal annealing. Optimal microwave annealed IGZO TFT exhibits mobility, SS, V_th, and V_H of 6.45 ㎠/Vs, 0.17 V/dec, 1.53 V, and 0.47 V, respectively. PBS and NBS stability tests confirm that microwave annealing can effectively improve the interface between the dielectric and the active layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.154-157
• /
• 2003

$TiO_2$ thin films were fabricated by RF magnetron sputtering system at by controlling deposition times, ratios of $Ar:O_2$ partial presser ratio and substrate conditions. And the surface, cross-section morphology, microstructure, and composition ratio of the films were analyzed by FE-SEM, TEM and XPS. Besides, the optical absorption and transmittance of the $TiO_2$ films were measured by a UV-VIS-NIR Spectrophotometer, and photocatalytic properties were studied by G${\cdot}$C Analyzer & Data Analysis system. As the result, when $TiO_2$ thin film was made at deposition time of 120[min] and $Ar:O_2$ ratio of 60:40, the best structural and optical properties among many thin films could be accepted. The best results of properties were as follows: thickness; 360~370[nm), grain size; 40[nm], gap between two peak binding energy; $5.8{\pm}0.05[eV]$ ($2_{p3/2}$ peak and $2_{p1/2}$ peak of Ti was show at $458.3{\pm}0.05[eV]$ and $464.1{\pm}0.05[eV]$ respectively), binding energy; $530{\pm}0.05[eV]$, optical energy band gap; 3.4[eV].

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1574-1576
• /
• 2003

Carbon nanotubes (CNTs) were grown on the TiN-coated silicon substrate with different thickness of Ni and Co catalysts layer at $600^{\circ}C$ using inductively coupled plasma-chemical vapor deposition (ICP-CVD). The Ni and Co catalysts were formed using the RF magnetron sputtering system with various deposition times. It was found that the growth of CNTs was strongly influenced by the surface morphology of Ni and Co catalysts. With increasing deposition time, the thickness of catalysts increased and the grain boundary size of catalysts increased. The surface morphology of catalysts and CNTs were elucidated by SEM. The Raman spectrum further confirmed the graphitic structure of the CNTs. The turn-on field of CNTs grown on Ni and Co catalysts was about 2.7V/pm and 1.9V/pm respectively. Field emission current density of CNTs grown on Ni and Co catalysts was measured as $11.67mA/cm^2$ at $5.5V/{\mu}m$ and $1.5mA/cm^2$ at $5.5V/{\mu}m$ respectively.