• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.585-588
• /
• 2002

The USM uses friction between a mobile part (rotor) and a vibration part(stator), which is different from the principle of the conventional motor based on the interaction of electric and magnetic fields. In this thesis, a flat-type $L_1-B_8$ mode USM was designed and fabricated the characteristics of an ultrasonic vibration. The results of fabricated USM are as follows: (1) In case of ultrasonic motor with elastic-body of stainless, when applied voltage, frequency, pressing force of rotor were 50 [V], 27.9 [kHz], 1.5 [N], 5.0[mN m] respectively, the speed of revolution could be presented up to 0 [cm/s]. (2) In case of ultrasonic motor with elastic-body of brass, when applied voltage, frequency, pressing force of rotor were 50 [V], 21.4 [kHz], 1.5 [N], 1.4[mN m]respectively, the speed of rotor revolution was presented up to 0 [cm/s]. (3) The USM of elastic-body of stainless showing 1.17[%], somewhat low, in the maximum efficiency according to torque was superior to the USM of elastic-body of brass showing 0.34 [%]. The Flat-type $L_1-B_8$ mode USM had characteristics of typical drooping torque-speed, large torque and high speed, and operating in both directions by phase reversal.

• 농업과학연구
• /
• 제46권4호
• /
• pp.723-735
• /
• 2019

The power-train is the most important component of an agricultural tractor. In this study, the strength of the driving gear transmission of an 82 kW-class tractor was analyzed using equivalent torque during plow tillage. The load measurement system consisted of an engine revolution speed sensor, torque-meters, revolution speed sensors for four axles, and pressure sensors for two hydraulic pumps. The load data were measured during plow tillage for four speed stages: F2 (2.78 km/h), F5 (5.35 km/h), F7 (7.98 km/h), and F8 (9.75 km/h). Aspects of the gear-strength such as bending stress, contact stress, and safety factors were analyzed under two torque conditions: the equivalent torque at the highest plow load for the F8 speed stage and the maximum engine torque. The simulation results using KISSsoft showed that the maximum engine torque conditions had a lower safety factor than did the highest equivalent torque condition. The bending safety factors were > 1 at all gear stages, indicating that gear breakage did not occur under actual measured operating conditions, nor under the maximum torque conditions. However, the equivalent torque condition in the contact stress safety factor was > 1, and the maximum torque condition was < 1 at the first gear pair. The method of analysis using the equivalent torque showed lower stress and higher safety factor than did the method using maximum torque. Therefore, when designing a tractor by applying actual working torque, equivalent torque method would support more reliable product development.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.39-48
• /
• 2006

In this research, in order to study the spray, combustion, and emission characteristics of the common rail DME engine, the target engine was disassembled, and 3D CAD file was constructed using a 3D measurement machine and a rapid prototyping machine. Using the obtained 3D geometry, fine moving meshes are generated, and three dimensional non-steady turbulence flow field and combustion phenomenon including spray were numerically analyzed. As a result, IMEP of DME and diesel in medium and high speed revolution showed similar performance. As the DME fuel start to burn in spray area, the vaporized fuel rapidly spreads squish area in low speed revolution. In the case of DME engine, CO and NOx are relatively consistent with experiment results. It was found that the break-up, evaporation, collision model of DME fuel need to be properly adjusted through matching the characteristics of fuel and injector for further improvement.

• Journal of Biosystems Engineering
• /
• 제29권6호
• /
• pp.487-494
• /
• 2004

This study was conducted to develope a fertilizer-soil incorporation band tiller for the walking cultivator. Because the mixing of soil and fertilizer in the furrow of dry-field has been done manually, several time, heavy labor and much man power were required for the job. This rotary type implement is developed to substitute this manual operation for soil-fertilizer incorporation. The results of this study are summarized as follows : 1) This implement was composed of tilling device, fertilizer application device, frame and tail wheel device. 2) The revolution of driving wheel was $11\~28\;rpm$, that of application roller was $13\~14\;rpm$ the application rate range per revolution of driving wheel was $4.43\~11.80\;g$g and the application rate range by the working speed and the opening quantity was $84.12\~557.20\;g/min$. 3) The adequate working speed was $0.20\~0.40\;m/s$ and the required minimum width of open furrow was 250 mm.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.224-237
• /
• 1995

An ECU(Electronic Control Unit) with 16 bit microcomputer has been developed. This system includes hardware and software for more precise control on fuel injection, ignition timing, and idle speed. This control system employs an air flow sensor of the hot wire type, a direct ignition system, an idle speed control system using a solenoid valve, and a crank angle sensor. Especially, the crank angle sensor provides two separate signals: One is the position signal(POS) which indicates 180 degree pulses per revolution, and the other is the reference signla(REF) that represents each cylinder individually. The conventional engine control system requires at least two engine revolutions in order to identify the cylinder number. However, the developed engine control system can recognize the cylinder number within a quarter of an engine revolution. Therfore, the developed engine control system has been able to control fuel injection and ignition timing more quickly and accurately, Furthermore, the number of misfire reduces during the cold start.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.809-814
• /
• 2009

Deep mixing method has been used for ground improvement and foundation system for embankment, port and harbor foundations, retaining wall, and liquefaction mitigations. It has attractive benefits because it is not only improved strength of soft ground but superior for prevention of settlement. However, the quality controls of improved mass affect to the efficiency of the deep mixing method is not properly established. These effects vary depending upon the construction environments and conditions of agitation in consideration of an agitator. The strength and shape of the improved column are not unique and these are affected by mechanical properties of agitators. In this study, in order to investigate the efficiency of deep mixing method for ground improvement on a soft clay ground, experimental studies are performed considering mechanical properties of agitator; the location of exit-hole of admixtures, an angle of mixing wing and a speed of revolution. The experiments are conducted with the simulated apparatus for deep mixing plant that reduced the scale in 1:8 of the real plant. According to the results, the diameter and shape of improved column mass vary depending on the mechanical properties and operating conditions of agitator. Its quality is better when the exit-hole of admixtures is located in the mixing wing, when an angle of mixing wing is large, and when the speed of revolution is rapid.

• 농업과학연구
• /
• 제11권1호
• /
• pp.160-175
• /
• 1984

로우터리 경운(耕耘)날의 회전속도(回轉速度) 및 작업속도(作業速度)가 경운소요(耕耘所要)토오크에 미치는 영향을 분석(分析)하기 위(爲)하여, 형상각(形狀角) ${\theta}=30^{\circ}$, $40^{\circ}$인 2종(種)의 경운(耕耘)날로 로우터리축(軸)을 204, 243, 285, 360rpm 4단계로, 전진속도(前進速度)는 29.40cm/s, 46.93cm/s로 변화(變化)시키면서 인공토양조(人工土壤槽)에서 dynamic strain gage system을 이용(利用)하여 경운소요(耕耘所要)토오크를 측정분석(測定分析)한 결과(結果)를 요약(要約)하면 다음과 같다. 1. 경운(耕耘)날의 회전속도(回轉速度) 및 전진속도(前進速度)는 경운소요(耕耘所要)토오크에 교호작용(交互作用)으로 영향(影響)을 미치는 것으로 분석(分析)되었으며, response surface analysis를 통(通)하여 분석(分析)한 수학적(數學的)인 모형(模型)은 다음과 같다. $$T=a_0+a_1V+a_2R+a_3VR+a_4VR^2$$ 여기서 T=경운소요(耕耘所要)토오크 (kg-m) $a_0$=당(當)수(數) $a_1,\;a_2,\;a_3,\;a_4$= 계(係)수(數) V=경운장치(耕耘裝置)의 전진속도(前進速度) (cm/s) R=경운(耕耘)날의 회전속도(回轉速度) (rpm) 2. 최대경운소요(最大耕耘所要)토오크는 로우터리날 회전속도(回轉速度)가 증가(增加)함에 따라 ${\frac{{\partial}T}{{\partial}V}}$는 증가(增加)하였으며, 200~220rpm에서 증가율(增加率)이 최저(最低)가 되었고, 같은 조건(條件)에서 ${\frac{{\partial}T}{{\partial}R}}$은 감소(減少)하는 경향(傾向)이었으며, 전진속도(前進速度)가 증가(增加)함에 따라 감소율(減少率)은 증가(增加)되었다. 3. 평균경운소요(平均耕耘所要)토오크는 회전속도(回轉速度)가 320~360rpm에서 ${\frac{{\partial}T}{{\partial}R}}$의 變化가 적었으며, ${\frac{{\partial}T}{{\partial}R}}$은 회전속도(回轉速度)가 증가(增加)함에 따라 감소율(減少率)이 증가(增加)되었다. 4. 전진속도(前進速度)에 대(對)한 토양(土壤)의 단위체적당(單位體積當) 평균경운소요(平均耕耘所要)토오크의 변화율(變化率)${\frac{{\partial}T}{{\partial}R}}$는 270~300rpm에서 최저(最低)가 되었으며, ${\frac{{\partial}T}{{\partial}R}}$은 V=29.40cm/s와 V=46.93cm/s일때 변화율(變化率)이 280~290rpm에서 교착(交錯)하였다. 5. 로우터리날의 형상각(形狀角)이 증가(增加)함에 따라 순경운소요동력(純耕耘所要動力)은 증가(增加)하였다. 그러나 실제(實際) 이용면(利用面)에서는 형상각(形狀角)이 작으면 로우터리날에 검불이 감기게 되므로 소요동력(所要動力)이 크게 증가(增加)함을 보여주는 연구결과도 있다. 그러므로 형상각(形狀角) 변화(變化)에 대(對)해서는 계속 연구(硏究)되어야 할 과제(課題)라 인정(認定)된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.806-809
• /
• 2000

The factors which can improve tool life in machining are consisted of tool geometries, tool materials, coating methods. cutting environments, cutting conditions and so on. Cutting speed in cutting conditions is one of the important factors which can directly influence on the tool life. This paper deals the machinability which is concerned about the cutting direction and the tilt angle of fret form surface in hot die steel(STD I I). The NC datum were analysrd and the effective tool diameters were calculated according to the change of tilt angle the program which can continue the cutting speed with the change of spindle revolution is developed.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.240-243
• /
• 2008

In this paper, the design of Centrifugal Compressor which is used in sizes 50 horse power has 8 pressure ratio and numerical analysis of the flow within compressor varying tip clearance length are performed. To get high pressure ratio with low power the exit height of impellers is low but compressor has very high speed of revolution. So compressor has high specific speed although mass flow rate is very small. The shape of impellers at the first stage is carried out. Flow and performance characteristics of impellers has been analyzed by using a commercial CFD program, $Fine^{TM}$/turbo. The result shows that loss coefficient is affected by tip clearance length and compressor has proper tip clearance length. It is possible to decrease loss by selecting apt tip clearance length.

• 연구논문집
• /
• 통권27호
• /
• pp.127-139
• /
• 1997

투포원 연사기는 스핀들 1회전에 2회의 꼬임을 부가하여 실의 신축성과 인장강도 및 내마모성을 증가시키며, 특수한 목적의 의장사를 만드는 섬유기계이다. 스핀들 유니트는 고속 회전중에 안정화된 운동이 지속되도록 구조설계가 요구되는 핵심장치로서 스핀들 유니트의 동특성 해석은 고속 스핀들 유니트설계의 최적화를 도모할 수 있을 것이다. 스핀들 유니트는 블레이드와 로타리 디스크로 구성되어 있으며, 스핀들 축에 대하여 회전체 형상을 유지 하고 있다. 동특성 해석을 수행하기 위하여 전달 매트릭스 해석법을 정의하고 해석용 프로그램인 SPINDLE을 이용하여 비틀림과 굽힘 고유진동수를 해석하였으며, 운전회전수에서 변위모우드를 분석하였다.