• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.329-334
• /
• 2002

High-speed machining is one of the most effective technology to improve productivity. Because of the high speed and high feed rate, high-speed machining can give great advantages for the machining of dies and molds. This paper describes on the improvement of machining accuracy in high-speed machining. Depth of cut, feed rate, spindle revolution and cutting force are control factors. The effect of the control factors on machining accuracy is discussed for the results of surface roughness and machining error in Z-direction for the high speed machining of STD11.

• 한국정밀공학회지
• /
• 제22권5호
• /
• pp.167-174
• /
• 2005

High-speed machining is one of the most effective technologies to improve productivity Because of the high speed and high feed rate, high-speed machining can give great advantages for the machining of dies and molds. This paper describes on the analysis and evaluation of cutting force in high-speed machining. Cutter rotation directions, slope directions, spindle revolution and depth of cut are control factors for cutting force. The effect of the control factors on cutting force is investigated for the high speed machining of STD11.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.690-695
• /
• 2004

The present study is an investigation on the characteristics of heavy load toque converter by experimental process. To get the dynamic performance, the dynamometer was used with a parameters of speed, torque, oil pressure and oil flux, etc. The torque converter was tested for various input speed, output oil pressure and input oil flow rate. All experiments were investigated in case that the speed ratio is increased. The torque ratio and capacity factor was in inverse proportion to speed. Engine revolution had a more effects at region of low speed ratio. But, the opposite phenomena were represented increase of efficiency. In result of this experiments, the characteristics of torque converter were not influenced by oil pressure and oil flux.

• 한국정밀공학회지
• /
• 제19권7호
• /
• pp.88-96
• /
• 2002

High-speed machining is one of the most effective technologies to improve productivity. Because of the high speed and high feed rate, high-speed machining can give great advantages for the machining of dies and molds. This paper describes on the improvement of machining accuracy in high-speed machining. Depth of cut, feed rate and spindle revolution are control factors. The effect of the control factors on machining accuracy is investigated using two-way factorial design.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.114-116
• /
• 2001

This study deals with friction stir welding of aluminum alloy(A5083). Welding conditions were applied that revolution 2000rpm, friction pressure 25MPa, angle between stir rod section and plate 4$^{\circ}$, projection pin diameter 4mm, traverse speed 0.5mm/sec, 1.0mm/sec, 1.5mm/sec. The experimental results as follows; 1. Welding beads were superior in traverse speed 1.0mm/sec and it were formed plenty of flash in traverse speed 0.5 mm/sec. Welding beads were rough in traverse speed 1.5mm/sec. 2. The maximum tensile strength was 211MPa in traverse speed 1.0mm/sec, in this case the strength was 85% of A5083 base metal tensile strength.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 Handout for 2000 Inter. Machine Tool Technical Seminar
• /
• pp.35-49
• /
• 2000

Over the past ten years we have wethnessed a revolution in metalcutting in the field of High Speed Machining. As machining speeds continue to increase, particularly spindle RPM, forces created by unbalance in the spindle, cutting tool, and toolholder require close attaention. It has been observed that these forces, if left uncompensated, can results in poor surface finish, loss of tool life, and spindle bearing failure. The sources of this unbalance needs to be identified and elimated in order to create a smooth, vibration free condition and allow the machine tool and its spindle to operate properly.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.30-38
• /
• 2003

High-speed machining is one of the most effective technology to enhance productivity especially for hardened die material. High-speed machining can give great advantages for machining of dies and molds. But selection of machining condition is very difficult because of complicated machining mechanism. This paper presents the selection of machining condition in high-speed machining of STD11. Depth of cut, feed rate and spindle revolution are control factors. The effect of the control factors on surface roughness and machining error in Z-direction is discussed to improve machining accuracy.

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권4호
• /
• pp.53-61
• /
• 1988

Speed of a diesel engine is usually controlled by the hydraulic governor which uses the centrifugal force of rotating fly balls for sensing the error speed. But for a recently developed high efficient, low speed and long stroke 2 cycle marine diesel engine, this governor doesn't work well enough because of too much changes of toraring force during one revolution of engine and too long uncontrollable time due to small numbers of cylinder. For improvement of jiggling phenomena and unstability various studies are being carried out, but they are not enough for a steep load change in a small ship's generator plant or at rough sea condition in a propulsion engine. In this paper, authors propose a new method to control a fuel before the change of angular velocity due to load change by feedforward the change of load, and find that the proposed method shows quite a good control performance in comparision to the customary PID control method by simulation using a digital computer for the various load change.

• 한국정밀공학회지
• /
• 제21권6호
• /
• pp.52-59
• /
• 2004

Recently the high speed end-milling processing is demanded the high-precise technique with good surface roughness and rapid time in aircraft, automobile part and molding industry. The working factors of high speed end-milling has an effect on surface roughness of cutting surface. Therefore this study was carried out to analyze the working factors to get the optimum surface roughness by design of experiment. From this study, surface roughness have an much effect according to priority on distance of cut, feed rate, revolution of spindle and depth of cut. By design of experiment, it is effectively represented shape characteristics of surface roughness in high speed end-milling. And determination($R^2$) coefficient of regression equation had a satisfactory reliability of 76.3% and regression equation of surface roughness is made by regression analysis.

• 한국전자통신학회논문지
• /
• 제14권2호
• /
• pp.369-376
• /
• 2019

본고에서는 제4차 산업혁명시대의 새로운 사이버보안 인텔리전스 서비스에 대응하는 지능형 정부 연구측면에서 바람직한 미래형 전자정부의 새로운 모습을 찾았다. 특히 제4차 산업혁명시대의 주요 특징인 중앙화 및 지능화의 측면에서 빅데이터 사이버보안기술에 주목하여 미래형 전자정부의 전략방안에 대해 고찰하였다. 연구결과 빅데이터를 활용한 보안분석기술이 적용되는 보다 고도화된 상관관계 분석을 통한 기존의 한계를 뛰어넘는 시스템 마련을 제시하였다. 제4차 산업혁명시대에 적합한 보안 정보 및 이벤트 관리 시스템 구축 측면에서 IT 시스템에서 발생하는 로그정보를 빅데이터 분석 기술을 적용해 보안 위협 여부를 선제적으로 탐지하는 인공지능과 같은 지능형의 고도화된 SIEM(Security Information & Event Management) 시스템 마련을 제안하였다. 제안된 시스템이 구현되면 제4차 산업혁명시대의 전자정부 보안에 있어 중앙화 및 집중화된 빅데이터 대상 확대, 증가된 데이터에 따른 처리속도 및 탐지 후의 대응까지 보다 지능화된 차원에서 선제적으로 기능할 수 있다.