• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.113-127
• /
• 2012

Face detection methods using image processing have been proposed in many different ways. Generally, the most widely used method for face detection is an Adaboost that is proposed by Viola and Jones. This method uses Haar-like feature for image learning, and the detection performance depends on the learned images. It is well performed to detect face images within a certain distance range, but if the image is far away from the camera, face images become so small that may not detect them with the pre-learned Haar-like feature of the face image. In this paper, we propose the far distance face detection method that combine the Aadaboost of Viola-Jones with a saliency map and user's attention information. Saliency Map is used to select the candidate face images in the input image, face images are finally detected among the candidated regions using the Adaboost with Haar-like feature learned in advance. And the user's eye-tracking information is used to select the interest regions. When a subject is so far away from the camera that it is difficult to detect the face image, we expand the small eye gaze spot region using linear interpolation method and reuse that as input image and can increase the face image detection performance. We confirmed the proposed model has better results than the conventional Adaboost in terms of face image detection performance and computational time.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1123-1128
• /
• 2016

Recently BLE beacon has been widely used as a method for measuring the indoor location in the IoT Technique. But it requires a filtering technique for the measurement of the correct position. It is used the most fixed beacon. It is not accurate that calculates the position information through the identification of the beacon signal. Therefore, filtering is important. So it takes a lot of time, position measurement and filtering. Thus, we is to measure the exact position at the indoor using a mobile beacon. The measured beacon signal is composed of an ontology for reuse in the same pattern. RSSI is measured the receiver is the distance of the beacon. And this value configure the location ontology to be normalized by the relationship analysis between the values. The ontology is a method for calculating the position information of the moving beacon. It can detect fast and accurate indoor position information and provide the service.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.9
• /
• pp.1027-1032
• /
• 2015

Using the radio wave, RFID(: Radio Frequency IDentification) wirelessly transmits the unique information saved in a tag attached on the specific object. In the construction area, the trend in using RFID for managing the input and inventory of the construction materials is upward. General management systems for the construction materials have only a function of identifying the tag attached on the construction materials, but the management system with a function of identifying and managing the location information of the construction materials employing RFID, for reusing it, is not actively developed. For the efficient reuse of the construction materials, in this paper, we propose the RFID system with a function of estimating and saving the location information of the specific construction materials, based on the estimated distances between the particular subs and reader. The proposed system consists of RFID reader, distance estimate, communication, and memory units.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.1
• /
• pp.63-72
• /
• 1998

Diversity in hardware and software is increasing ever and our networked computing environment is becoming more diverse. The development of software becomes expensive works because of a collection of diverse computers, storing various data type in different places, working together by incompatabilities of operating system and various databases and protocols. CORBA is a standard for distributed computing environment and for system integration of heterogeneous distributed environment. CORBA provides many technical benefits for effective system integration and seamless infrastructure for distributed communication environment of heterogeneous systems. In this paper, we proposed a system integraton model based on CORBA for distributed object environment, softwarc reuse and the intcrconnecion of WWW. The model is composed of factory server, trading server, convcrsion scrvcr and applicaton scrvcr. Thc proposed model can easy application development and system integration. And we implcmcntcd thc gateway for cooperation with WWW. As a proof of the proposed model, we show how the distance learning system designed using the services provided by the proposed model.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.6A
• /
• pp.476-483
• /
• 2009

Recently much attention has been devoted to femtocell's potential to improve indoor cellular coverage and high speed wireless communications. Femtocell based commercial services have been already launched in some countries and standardization activities are actively on-going, there has been concern however over potential issues of interference between femtocells and the micro/macro networks. With universal frequency reuse, the ensuing cross-tier interference causes unacceptable data rate and outage probability, so an analysis of effect of interference in femtocell embedded networks would be necessary for a stable system design. This paper investigates the effect of interference on system performances of femtocell embedded hierarchical cell structure (HCS) networks considering the characteristics of propagation environments. Various channel parameters are specially considered for indoor environments where most of femtocells are deployed to investigate the effect of interference of femtocell embedded RCS networks. System capacity and coverage are provided with variant distance between macrocell and femtocell, location of the user in femtocell coverage, and characteristic of building structures.

• Steel and Composite Structures
• /
• v.36 no.3
• /
• pp.321-337
• /
• 2020

Contemporary design and construction of steel-concrete composite structures employs the use of prefabricated concrete elements and demountable shear connectors in order to reduce the construction time and costs and enable dismantling of elements for their potential reuse at the end of life of buildings. Bolted shear connector with mechanical coupler is presented in this paper. The connector is assembled from mechanical coupler and rebar anchor, embedded in concrete, and steel bolt, used for connecting steel to concrete members. The behaviour and ultimate resistance of bolted connector with mechanical coupler in wide and narrow members were analysed based on push-out tests and FE analyses conducted in Abaqus software, with focus on concrete edge breakout and bolt shear failure modes. The effect of concrete strength, concrete edge distance and diameter and strength of bolts on failure modes and shear resistance was analysed. It was demonstrated that premature failure by breakout of concrete edge occurs when connectors are located 100 mm or closer from the edge in low-strength and normal-strength reinforced concrete. Furthermore, the paper presents a relatively simple model for hand calculation of concrete edge breakout resistance when bolted connectors with mechanical coupler are used. The model is based on the modification of prediction model used for cast-in and post-installed anchors loaded parallel to the edge, by implementing equivalent influence length of connector with variable diameter. Good agreement with test and FE results was obtained, thus confirming the validity of the proposed method.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.229-237
• /
• 2011

In this paper, a 60 GHz LTCC SiP with low-power CMOS OOK modulator and demodulator is presented. The 60 GHz modulator is designed in a 90-nm CMOS process. The modulator uses a current reuse technique and only consumes 14.4-mW of DC power in the on-state. The measured data rate is up to 2 Gb/s. The 60 GHz OOK demodulator is designed in a 130nm CMOS process. The demodulator consists of a gain boosting detector and a baseband amplifier, and it recovers up to 5 Gb/s while consuming low DC power of 14.7 mW. The fabricated 60 GHz modulator and demodulator are fully integrated in an LTCC SiP with 1 by 2 patch antenna. With the LTCC SiP, 648 Mb/s wireless video transmission was successfully demonstrated at wireless distance of 20-cm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.326-327
• /
• 2016

A study on Ontology-based indoor positioning techniques using BLE Beacon. Recently BLE beacon has been widely used as a technique for measuring the indoor location. But it requires a filtering technique for the measurement of the correct position, and uses the most fixed beacon. It is not accurate that calculates the position information through the identification of the beacon signal. Therefore, filtering is important. So it takes a lot of time, position measurement and filtering. Thus, we is to measure the exact position at the indoor using a mobile beacon. The measured beacon signal is composed of an ontology for reuse in the same pattern. RSSI is measured the receiver is the distance of the beacon. And this value configure the location ontology to be normalized by the relationship analysis between the values. The ontology is a method for calculating the position information of the moving beacon. It may be detected fast and accurate indoor position information.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.60-71
• /
• 1998

The propagation environment is effected by Rayleigh fading, Rician fading, path loss and lognormal shadowing in microcellular mobile radio system. In these surroundings we analysed the performance on received Rician signals among L Rician interferers and the characteristics of lognormal shadowing for various parameters such as reuse distance, cluster size, signal to interference power ratio and protection ratio using outage probability. We also studied various channels Rayleigh signal and Rician interferer, Rician signal and Rayleigh interferer, Rician signal and Rician interferer and so on using outage probability. The theoretical extention and computer simulation effectively analysed the characteristic of lognormal shadowed Rician channel.

• Korean Chemical Engineering Research
• /
• v.56 no.1
• /
• pp.6-13
• /
• 2018

Utilizing the heat of cooling water discharge of coal-fired power plant, pipeline investment costs for businesses that supply heat to agricultural facilities near power plants increase in proportion to installation distance. On one hand, the distance from the power plant is a factor that brings difficulties to secure economic efficiency. On the other, if the installation distance is short, there is a problem of securing the heating demands, facility houses, which causes economical efficiency to suffer. In this study, the economic efficiency of 1km length of standard heat pipeline was evaluated. The sensitivity of the heat pipe to the new length variation was analyzed at the level of government subsidy, amount of heating demand and the incremental rate of pipeline with additional government subsidy. As a result of the analysis, it was estimated that NPV 131 million won and IRR 15.73%. The sensitivity analysis showed that NPV was negative when the length of heat pipe facility exceeded 2.6 km. If the government supports 50% of the initial investment, the efficiency is secured within the estimated length of 5.3 km, and if it supports 80%, the length increases within 11.4 km. If the heat demand is reduced to less than 62% at the new length of the standard heat pipe, it is expected economic efficiency is not obtained. If the ratio of government subsidies to initial investment increases, the elasticity of the new bloc will increase, and the fixed investment, which is the cost of capital investment for one unit of heating demand, will decrease. This would result in a reduction in the cost of production per unit, and it would be possible to supply heat at a cheaper price level to the facility farming. Government subsidies will result in the increased economic availability of hot plumbing facilities and additional efficiencies due to increased demand. The greater government subsidies to initial investment, the less farms cost due to the decrease in the price per unit. The results of the study are significant in terms of the economic evaluation of the effectiveness of the government subsidy for the thermal power plant heat utilization project. The implication can be applied to any related pilot to come.