• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.14-23
• /
• 1997

In this paper, the results of the measurement and analysis of extremely low frequency(ELF) electric field in the vicinity of 154[kV] overhead transmission lines have been described. The planar-type electric field sensor has been fabricated by three dimensional structure with special consideration of taking the power frequency and lower components. The calibration experiments have been carried out according to the procedures of IEEE recommendation. The electric field measuring system has the frequency bandwidth of 7[Hz] to 2.7[MHz] and the response sensitivity of 0.094[mV/V/m]. Also the practical measurements of electric field under an 154[kV] double circuit overhead transmission lines have been made and analyzed. It was known that the lateral electric field profiles under an 154[kV] double circuit overhead transmission lines show the asymmetrical distributions owing to the environmental metal frame structures and their maximum electric field magnitude is less than 3[kV/m]. It can be concluded that the measured results of the electric fields satisfy with all limits or guidelines of the various authorized international institutes' recommendations.

• The Journal of Fisheries Business Administration
• /
• v.30 no.1
• /
• pp.1-29
• /
• 1999

When the international fisheries order changes following the UN Law of the Sea, the new regional fisheries order is forming among East North Asian states and era of Economic Zones is really coming. In those changes of foreign and domestic fisheries environment, to maintain sustainable growth of the industry in 21st century the North East Asian states plot adjustments to fisheries management, such as introduction of the TAC system and others. The TAC seems to be an appropriate systematic response especially because traditional functions of fisheries management have already demonstrated their limits in regards to fisheries sustainable development. Introduction of the TAC to the North East Asian fisheries not only resolves the inability of traditional fisheries management to develop the industry consequently, but also strengthens the EEZ and existing marine management systems. However, the TAC was born by thewestern industrial mentality, still contains persistent mistakes and is difficult to change. Therefore, its introduction to and implication in North East Asian region might cause numerous problems. From this point of view, introduction of the TAC system will disregard peculiarities of North East Asian fisheries, so main efforts should be concentrated on improving the functions of existing system via consecutive step-by-step approach. In addition, the TAC should be grafted into the existing fisheries system through cooperative management system, creating stable systematic ground and considering scientific and fisheries motives. Especially, TAC system, unlike the traditional fisheries' management system, is scientific, being systematically developed one, and needs to be gradually installed, considering its systematic character. Therefore, the TAC should better be introduced by systematic and scientific approaches, paying more attention to strengthening the existing fisheries system, but not immediately and in the form it is right now. Concluding, introduction of the TAC can not be made considering the outward factors deriving from the UN Law of the Sea without corrections.'h overcome limitations and ineffectiveness of traditional fisheries, most efforts should be concentrated on basic revision of 21st centuries' fisheries and strengthening the functions of traditional fisheries aimed to develop the leading business of marine industries.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.216-227
• /
• 2005

The head penetrations for control rod drive mechanism and instrumentation systems are installed at the reactor pressure vessel head of PWRs. Primary coolant water and the operating conditions of PWR plants can cause cracking of these nickel-based alloy through a process called primary water stress corrosion cracking (PWSCC). Inspection of the head penetrations to ensure the integrity of the head penetrations has been interested since reactor coolant leakages were found at U. S. reactors in 2000 and 2001. The complex geometry of the head penetrations and the very low echo amplitude from the fine, multiple flaws due to the nature of the see made it difficult to detect and size the flaws using conventional pulse-echo UT methods. Time-of-flight-diffraction technique, which utilizes the time difference between the flaw tips while pulse-echo does the flaw response amplitude from the flaw, has been selected for this inspection for it's best performance of the detection and sizing of the head penetration see flaws. This study defines the limits of the detectable and accurately sizable minimum flaw size which can be detected by the General TOFD and the Delta TOFD techniques for circumferentially and axially oriented flaws respectively. These results assures the reliability of the inspection techniques to detect and accurately size for various kind of flaws, and will also be utilized for the future development and qualifications of the TOFD techniques to enhance the detecting sensitivity and sizing accuracy of the flaws of the reactor head penetrations in nuclear power plants.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.2
• /
• pp.151-159
• /
• 2015

PURPOSE. To describe and characterize the surface topography and cleanliness of CAD/CAM manufactured zirconia abutments after steaming and ultrasonic cleaning. MATERIALS AND METHODS. A total of 12 ceramic CAD/CAM implant abutments of various manufacturers were produced and randomly divided into two groups of six samples each (control and test group). Four two-piece hybrid abutments and two one-piece abutments made of zirconium-dioxide were assessed per each group. In the control group, cleaning by steam was performed. The test group underwent an ultrasonic cleaning procedure with acetone, ethyl alcohol and antibacterial solution. Groups were subjected to scanning electron microscope (SEM) analysis and Energy-dispersive X-ray spectroscopy (EDX) to verify and characterize contaminant chemical characterization non- quantitatively. RESULTS. All zirconia CAD/CAM abutments in the present study displayed production-induced wear particles, debris as well as organic and inorganic contaminants. The abutments of the test group showed reduction of surface contamination after undergoing an ultrasonic cleaning procedure. However, an absolute removal of pollutants could not be achieved. CONCLUSION. The presence of debris on the transmucosal surface of CAD/CAM zirconia abutments of various manufacturers was confirmed. Within the limits of the study design, the results suggest that a defined ultrasonic cleaning process can be advantageously employed to reduce such debris, thus, supposedly enhancing soft tissue healing. Although the adverse long-term influence of abutment contamination on the biological stability of peri-implant tissues has been evidenced, a standardized and validated polishing and cleaning protocol still has to be implemented.

• Journal of the Korean Chemical Society
• /
• v.47 no.1
• /
• pp.31-37
• /
• 2003

The expanded uncertainties calculated by the application of GUM -approximation and Monte-Carlo simulation were compared about the model equation of one-point calibration which is widely used for the measurements and chemical analysis. For the comparisons, we assumed a set of artificial data at the various level of concentration and dispersion of t or normal distribution. Mistakes of more then 50 % was revealed at the values calculated by GUM-approximation in comparison with those of Monte-Carlo simulation because of the excess dispersion from t-distribution and non-linearity by division in the equation. In contrary, the mistake of calculation due to non-linearity of the equation was not observed in the level of detection limits with the equation of one-point calibration, because of the relatively large values of uncertainty in response.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.1
• /
• pp.50-60
• /
• 2013

High temperature proton exchange membrane fuel cells (PEMFCs) using phosphoric acid (PA) doped polybenzimidazole (PBI) membranes have been concentrated as one of solutions to the limits with traditional low temperature PEMFCs. However, the amount of reported experimental data is not enough to catch the operational characteristics correlated with cell performance and durability. In this study, design of experiments (DOE) based operational optimization method for high temperature PEMFCs has been proposed. Response surface method (RSM) is very useful to effectively analyze target system's characteristics and to optimize operating conditions for a short time. Thus RSM using central composite design (CCD) as one of methodologies for design of experiments (DOE) was adopted. For this work, the statistic models which predict the performance and degradation rate with respect to the operating conditions have been developed. The developed performance and degradation models exhibit a good agreement with experimental data. Compared to the existing arbitrary operation, the expected cell lifetime and average cell performance during whole operation could be improved by optimizing operating conditions. Furthermore, the proposed optimization method could find different new optimal solutions for operating conditions if the target lifetime of the fuel cell system is changed. It is expected that the proposed method is very useful to find optimal operating conditions and enhance performance and durability for many other types of fuel cell systems.

• Journal of The Korean Dental Society of Anesthesiology
• /
• v.8 no.1
• /
• pp.1-9
• /
• 2008

Common dental procedures (local anesthesia and dental treatment) are potentially stress-inducing in many patients, especially medically compromised patients. The body response to dental stress involves the cardiovascular system (an increase in cardiovascular workload), the respiratory organ and the endocrine system (change in metabolism). To minimize the stress to the medical risk patient, the stress reduction protocol was established. The obtained contents were as follows: (1) Recognize the patient's degree of medical risk (2) Complete medical consultation before dental therapy (3) Schedule the patient's appointment in the morning (4) Monitor and record preoperative, perioperative and postoperative vital signs (5) Use psychosedation during therapy (6) Use adequate pain control during therapy (7) Short length of appointment: do not exceed the patient's limits of tolerance (8) Follow up with postoperative pain/anxiety control (9) Telephone the higher medical risk patient later on the same day that treatment was given. This protocol is predicated on the belief that the prevention of or reduction of stress ought to begin before the start of an appointment, continue throughout treatment, and, if indicated, into the postoperative period. The authors used the stress reduction protocol in the care of local anesthesia infected teeth in medically compromised patients. The final prognosis was comfortable without any complications.

• The KIPS Transactions:PartC
• /
• v.12C no.2 s.98
• /
• pp.191-200
• /
• 2005

The brilliant achievements in computers and the internet technology make it easy for users to get useful information. But at the same time, the damages caused by intrusions and denial of service attacks are getting more worse. Specially because denial of service attacks by internet worm incapacitate computers and networks, we should draw up a disposal plan against it. So far many rule-based intrusion detection systems have been developed, but these have the limits of these ability to detect new internet worms. In this paper, we propose a system to detect intrusion and generate detection rule against scan-based internet worm, paying attention to the fact that internet worms scan network to infect hosts. The system detects internet worms using detection rule. And if it detects traffic causing by a new scan-based internet worm, it generates new detection nile using traffic information that is gathered. Therefore it can response to new internet worms early. Because the system gathers packet payload, when it is being necessary only, it can reduce system's overhead and disk space that is required.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.6
• /
• pp.78-84
• /
• 2009

This paper presents measurement results of transient impedance for small-sized ground electrodes in a discharge region of soil. For a realistic analysis of ionization characteristics near the ground electrode, three types of ground rod installed outdoors and high voltage impulse generator were used for injecting test current. From the analysis of response voltage and current flowing ground electrode to earth, it is verified that the ionization near the ground electrode contributes to reduction of ground impedance and limits the ground potential rise effectively in high resistivity soil. As a threshold electric field density for ionization is small in low resistivity soil, the shape of ground electrode rarely contributes to the transient impedance. And, from the experiment result with shape of ground electrode, the rod with needles is more effective to reduce the transient impedance than the plate electrode in the voltage range including with ionization regions of soil.

• Journal of Korean Society of Rural Planning
• /
• v.18 no.3
• /
• pp.1-11
• /
• 2012

This study postulates a study model to examine the effect on the local economy revitalization of a selection of local resources, the local innovation capability strengthening, the establishment of promotion system and the creation of revenues for the participant groups of the local industry promotion project. To accomplish study purposes, 169 response samples from 85 project groups which drive the local industry promotion project were verified using SPSS 12.0 and AMOS 5.0. The results showed that firstly, the selection of local resources had a significant effect on the local innovation capability strengthening. Secondly, the local innovation capability strengthening had a significant effect on the establishment of promotion system. Thirdly, the establishment of promotion system had a significant effect on the creation of revenues. Fourthly, the selection of local resources didn't have an effect on the revitalization of local economy. Fifthly, both the local innovation capability strengthening and the establishment of promotion system didn't have an effect on the revitalization of local economy. Sixthly, the creation of revenues had a significant effect on the revitalization of local economy. According to the verifications of study model, the revitalization of local economy is achieved by inducing creation of revenues through the local innovation capability strengthening and the establishment of promotion system after the selection of local resources. From these results, this study presents suggestions, limits of study and directions in the future study.