• 제목/요약/키워드: Response AC/A ratio

검색결과 27건 처리시간 0.045초

가입렌즈 도수와 프리즘 굴절력 변화에 따른 반응 AC/A비와 CA/C비 비교 (Comparison between Response AC/A and CA/C Ratio according to Additional Spherical Powers and Prism Powers)

  • 노병호;유동식;손정식;곽호원
    • 한국안광학회지
    • /
    • 제20권3호
    • /
    • pp.341-347
    • /
    • 2015
  • 목적: 가입렌즈 도수 변화에 따른 반응 AC/A비와 프리즘 굴절력 변화에 따른 CA/C비를 측정하고, 이 두 변수와 PD 및 상대조절력과의 상관관계, 반응 AC/A비의 역수와 CA/C비 사이의 평균차이를 비교하여 임상에서 굴절력 및 프리즘 처방의 자료로 활용하고자 한다. 방법: 20대 대학생(평균 $22.62{\pm}2.84$세) 62명(남 50명, 여12명)을 대상으로 주시거리 40 cm에서 하웰시표(Howell card)와 개방형굴절력계(Nvision-K 5001, Shin nippon)를 이용하여 가입렌즈 도수 변화에 따른 반응 AC/A비를 측정하였고, CA/C비는 Wesson fixation card(WFC Bernell, USA) 이면의 DOG시표와 개방형굴절력계를 사용하여 프리즘 굴절력 변화에 따른 CA/C비를 측정하였다. 결과: 가입렌즈 도수 변화에 따른 조절반응량이 프리즘 굴절력 변화에 따른 조절반응량보다 통계적으로 유의한 차이가 크게 나타났다. 동공간 거리와 반응 AC/A비의 설명변량 $R^2=0.025$으로 나타났으며, PD와 CA/C비는 설명변량 $R^2=0.009$으로 나타났다. 상대조절력과 반응 AC/A비의 설명변량 $R^2=0.064$으로 나타났으며 상대조절력과 CA/C비의 설명변량 $R^2=0.321$로 상대조절력과의 예측가능한 상관관계가 있는 것으로 나타났다. 반응 AC/A비와 CA/C비의 설명변량 $R^2=0.126$으로 낮은 상관관계가 있는 것으로 나타났다(p=0.000). 반응 AC/A비의 역수와 CA/C비 사이의 평균차이는 $0.12{\pm}0.06D/{\Delta}$로 통계적으로 유의한 차이를 보였다(p=0.000). 결론: 상대조절력과 CA/C비의 상관관계는 상대조절력이 높은 사람일수록 폭주자극에 대한 폭주성 조절반응량이 큰 것으로 나타났다. 반응 AC/A비의 역수와 CA/C비는 통계적으로 유의한 차이를 보이므로 독립적인 변수로 임상에서 낮은 AC/A비를 가진 환자라도 높은 CA/C비를 가질 수 있다. 이에 양안시 이상에서 프리즘을 처방 할 경우 AC/A비가 정상범위라 하더라도 CA/C비는 다를 수 있어 반드시 조절반응량을 고려한 처방이 되어야 한다.

Gradient AC/A비와 Calculated AC/A비의 비교에 의한 근접성 폭주비(PC/A)에 관한 연구 (Study on Proximal Convergence/Accommodation(PC/A) Ratio by Comparison of Gradient AC/A Ratio and Calculated AC/A Ratio)

  • 한경애;성아영
    • 한국안광학회지
    • /
    • 제9권2호
    • /
    • pp.223-231
    • /
    • 2004
  • 기존에 이루어진 대부분의 AC/A비에 관한 연구들은 주로 Gradient AC/A비를 측정함으로써 진행되어 왔다. 본 연구는 Gradient AC/A비와 Calculated AC/A비를 함께 측정해 봄으로써 Gradient AC/A비 만을 측정했을 경우에는 나타나지 않는 근접성 폭주비 (Proximal Convergence/Accommodation)에 대한 고찰을 통해서 AC/A비의 임상 활용도를 높이는 데 그 목적이 있다. 124명의 검사대상은 최대시력을 단안 각각 1.0이상으로 원용교정을 하였으며 동적 검영법을 실시하여 조절기능의 이상 유무를 확인한 뒤 각각 Calculated AC/A비와 Gradient AC/A비를 측정하여 PC/A비를 구하였다. 연구결과 양안시 이상 그룹별 평균 Calculated AC/A비와 평균 Gradient AC/A비의 차이는 근접성 폭주 때문임을 보여주었다. 따라서, AC/A비의 임상 활용도를 높이기 위해서는 PC/A비를 포함한 근접성 (proximity)이라는 시기능변수 전반에 관한 지속적인 연구가 필요함을 확인할 수 있었다.

  • PDF

사위별 가입렌즈에 따른 자극 AC/A비와 반응 AC/A비의 비교 (Comparison between Stimulus and Response AC/A Ratios for Each Phoria with Additional Spherical Power)

  • 이세희;유동식;손정식;곽호원
    • 한국안광학회지
    • /
    • 제19권3호
    • /
    • pp.345-351
    • /
    • 2014
  • 목적: 각 사위 그룹에서 가입렌즈에 따른 조절반응량과 근거리 수평사위도의 변화를 측정하여 자극 AC/A비와 반응 AC/A비를 조사하였다. 이에 자극 AC/A비와 반응 AC/A비를 비교 분석하여 임상에서의 양안시 검사 및 처방시에 유용한 자료로 제시하고자 한다. 방법: 평균 만 $20.89{\pm}1.92$세, 81명을 대상으로 주시거리 40 cm에서 개방형 자동굴절계(Nvision-K 5001, Shin nippon)와 수정된 토링톤 시표(MIM card; Muscle Imbalance Measure card, Bernell)를 이용하여 양안시 상태에서 조절반응량과 근거리 수평사위도를 측정하였다. 그리고 측정된 값을 토대로 자극 AC/A비와 반응 AC/A비를 경사 AC/A법으로 계산하였다. 결과: 주시거리 40 cm에서 조절반응량은 외사위 그룹이 $1.92{\pm}0.26$ D로 가장 크고, 정위 그룹 $1.72{\pm}0.26$ D, 내사위 그룹 $1.62{\pm}0.42$ D 순으로 작아졌고, 근거리 수평사위도의 변화폭은 내사위 그룹이 $23.24{\Delta}$로 가장 크고, 정위 그룹 $19.76{\Delta}$, 외사위 그룹 $15.14{\Delta}$ 순으로 작게 나타났다. 가입렌즈에 따른 자극 AC/A비와 반응 AC/A비의 차이는 외사위 그룹에서는 -2.00 D 렌즈를 가입하였을 때, $1.72{\Delta}/D$로 가장 컸고 내사위 그룹에서는 +1.00 D 렌즈를 가입하였을 때 $3.43{\Delta}/D$로 가장 크게 나타났다. 외사위 그룹에서 -2.00 D, -1.00 D 렌즈를 가입하였을 때, 내사위 그룹에서는 +3.00 D, +2.00 D, +1.00 D, -1.00 D 렌즈를 가입하였을 때 각각 통계적으로 유의한 차이를 보였다. 결론: 자극 AC/A비와 반응 AC/A비를 비교하였을 때, 외사위 그룹에서는 (-) 렌즈를 가입하였을 때의 차이가 더 크고, 내사위 그룹에서는 (+) 렌즈를 가입하였을 때의 차이가 더 크게 나타났다. 또한 내사위 그룹의 자극 AC/A비와 반응 AC/A비의 차이가 외사위 그룹의 차이보다 더 크게 나타났다.

Neoadjuvant PD-1 Inhibitor Plus Apatinib and Chemotherapy Versus Apatinib Plus Chemotherapy in Treating Patients With Locally Advanced Gastric Cancer: A Prospective, Cohort Study

  • Chunjing Wang;Zhen Wang;Yue Zhao;Fujing Wang
    • Journal of Gastric Cancer
    • /
    • 제23권2호
    • /
    • pp.328-339
    • /
    • 2023
  • Purpose: This study aimed to evaluate the efficacy and safety of neoadjuvant programmed cell death-1 (PD-1) inhibitors plus apatinib and chemotherapy (PAC) in patients with locally advanced gastric cancer (LAGC). Materials and Methods: Seventy-three patients with resectable LAGC were enrolled and named the PAC group (n=39) or apatinib plus chemotherapy (AC) group (n=34) based on the treatment they chose. Neoadjuvant therapy was administered in a 21-day cycle for 3 consecutive cycles, after which surgery was performed. Results: The PAC group exhibited a higher objective response rate than the AC group (74.4% vs. 58.8%, P=0.159). Moreover, the PAC group showed a numerically better response profile than the AC group (P=0.081). Strikingly, progression-free survival (PFS) (P=0.019) and overall survival (OS) (P=0.049) were prolonged, whereas disease-free survival (DFS) tended to be longer in the PAC group than in the AC group (P=0.056). Briefly, the 3-year PFS, DFS, and OS rates were 76.1%, 76.1%, and 86.7% in the PAC group and 46.9%, 49.9%, and 70.3% in the AC group, respectively. Furthermore, PAC (vs. AC) treatment (hazard ratio=0.286, P=0.034) was independently associated with prolonged PFS in multivariate Cox regression analyses. The incidence of adverse events did not differ between the two groups (all P>0.05), where leukopenia, anemia, hypertension, and other adverse events were commonly observed in the PAC group. Conclusions: Neoadjuvant PAC therapy may achieve a preferable pathological response, delayed progression, and prolonged survival compared to AC therapy with a similar safety profile in patients with LAGC; however, further validation is warranted.

무정전전원장치(UPS)의 진동대 실험 및 동적특성 분석 (Investigation of Dynamic Characteristcs Uninterruptible Power Supply System (UPS) Using Shaking Table Tests)

  • 이승재;김주영;최경규
    • 대한건축학회논문집:구조계
    • /
    • 제35권11호
    • /
    • pp.129-136
    • /
    • 2019
  • Non-structural elements are vulnerable to earthquake ground motion. In this study, an experimental study for the electrical non-structural element was performed using tri-axial shaking table tests. A 100kVA UPS(Uninterruptible Power Supply system) was used as the test specimen. The test specimen was anchored to the concrete slab using the conventional installation detail. The input acceleration were generated in accordance with ICC-ES AC156 code. Scale factors of the input acceleration with respect to the required response spectrum defined in ICC-ES AC156 were from 25% to 600%. Based on the test results, damage and dynamic characteristics of UPS were evaluated and analyzed including natural frequency, damping ratio, acceleration time history response, dynamic amplification factor and relative displacement.

난류 예혼합 연소기에서의 흡입 유동 섭동에 대한 화염의 동적 거동 (Flame Dynamic Response to Inlet Flow Perturbation in a Turbulent Premixed Combustor)

  • 김대식
    • 한국연소학회지
    • /
    • 제14권4호
    • /
    • pp.48-53
    • /
    • 2009
  • This paper describes the forced flame response in a turbulent premixed gas turbine combustor. The fuel was premixed with the air upstream of a choked inlet to avoid equivalence ratio fluctuations. To impose the inlet flow velocity, a siren type modulation device was developed using an AC motor, rotating and static plates. Measurements were made of the velocity fluctuation in the nozzle using hot wire anemometry and of the heat release fluctuation in the combustor using chemiluminescence emission. The test results showed that flame length as well as geometry was strongly dependent upon modulation frequency in addition to operating conditions such as inlet velocity. Convection delay time between the velocity perturbation and heat release fluctuations was calculated using phase information of the transfer function, which agreed well with the results of flame length measurements. Also, basic characteristics of the flame nonlinear response shown in the current test conditions were introduced.

  • PDF

3상 Z-소스 PWM 정류기의 입력 AC 전압 센서리스 제어 (Input AC Voltage Sensorless Control for a Three-Phase Z-Source PWM Rectifier)

  • 한근우;정영국;임영철
    • 전기학회논문지
    • /
    • 제62권3호
    • /
    • pp.355-364
    • /
    • 2013
  • Respect to the input AC voltage and output DC voltage, conventional three-phase PWM rectifier is classified as the voltage type rectifier with boost capability and the current type rectifier voltage with buck capability. Conventional PWM rectifier can not at the same time the boost and buck capability and its bridge is weak in the shoot- through state. These problems can be solved by Z-source PWM rectifier which has all characteristic of voltage and current type PWM rectifier. By shoot-through duty ratio control, the Z-source PWM rectifier can buck and boost at the same time, also, there is no need to consider the dead time. This paper proposes the input AC voltage sensorless control method of a three-phase Z-source PWM rectifier in order to accomplish the unity input power factor and output DC voltage control. The proposed method is estimated the input AC voltage by using input AC current and output DC voltage, hence, the sensor for the input AC voltage detection is no needed. comparison of the estimated and detected input AC voltage, estimated phase angle of the input voltage, the output DC voltage response for reference value, unity power factor, FFT(Fast Fourier Transform) of the estimated voltage and efficiency are verified by PSIM simulation.

전류 감쇠 조정 회로에서의 정밀도 향상 기술 (Accuracy Enhancement Technique in the Current-Attenuator Circuit)

  • 김성권
    • 조명전기설비학회논문지
    • /
    • 제19권8호
    • /
    • pp.116-121
    • /
    • 2005
  • 전류모드 아날로그 회로를 이용하여 FIR(Finite Impulse Response) 필터를 설계하는 경우에 tap coefficient와 전류모드 FFT(Fast Fourier Transform) LSI의 회전인자(twiddle factor)를 실현시키기 위해서는 높은 정밀도를 갖는 전류 감쇠 회로가 필요하게 된다. 본 논문은 전류 모드 신호처리 기술에서 전류감쇠 회로의 감쇠 정밀도를 향상시킬 수 있는 기술을 소개하고자한다. 먼저 게이트 길이 비율을 조정하는(gate-ratioed) Current Mirror 회로를 사용하는 기존의 전류 감쇠 조정회로에 있어서의 DC offset 전류 에러에 대하여 분석하였으며, 다음으로 DC offset 전류 에러를 제거할 수 있는 전류감쇠 회로를 제안하였다. 회로 구성은 입력 전류를 1/N로 감쇠시킬 수 있도록 N개의 Current Mirror를 병렬로 연결하는 기본 구성을 하였으며, Kirchhoff 전류 법칙에 근거하여, 전류 감쇠가 결정되도록 설계하였다. 또한 Current Mirror 회로에서, 정전류원의 사용을 줄일 수 있는 회로설계를 제안하였다. 제안된 전류 감쇠 회로에서 정밀도는 Current Mirror의 ac 이득 에러에 의하여 제한되며 High Swing Current Mirror를 기본 Current Mirror로 사용한 경우에, 최대 정밀도는 이론상 입력 전류의 -80[dB]까지 실현가능하다.

자돈 설사병에 대한 형질전환 당근백신의 방어 효능 평가 (Protective effects of a transgenic carrot vaccine on piglet diarrhea)

  • 김영훈;남진영;이향근;황철호;한정희
    • 대한수의학회지
    • /
    • 제51권2호
    • /
    • pp.151-158
    • /
    • 2011
  • The study evaluated whether a transgenic carrot vaccine could induce a K88-specific immune response in sows and whether the resultant maternal antibody could protect piglets against enterotoxigenic Escherichia coli (ETEC) K88ac infection. Sows (n = 15) selected randomly from a farm in Korea were assigned to three groups (n = 5 per group: control [untreated]), group A (orally inoculated with a nontransgenic and transgenic carrot vaccines at 2 and 4 weeks ante partum, respectively), and group B (conventionally vaccinated according to the manufacturer's instructions). After 7 days of lactation, 5 piglets selected randomly from each group were challenged with $1{\times}10^{10}$ colony forming units/mL ETEC K88ac. Group C had the lowest mean fecal consistency score on post-challenge days 1 and 7. Histiologically, On post-challenge day 7, group C showed an increased duodenum and ileum villus:crypt ratio, compared to group A in the duodenum, with group B displaying the highest ratio. Groups B and C had more increased villus width than group A in the jejunum. Group C displayed the greatest increase in villus width in the ileum. The colostrums and serum from groups B and C displayed higher concentrations of IgA and IgG against ETEC K88, compared to group A. Based on the results, it was concluded that the transgenic carrot vaccine in sow per oral may have an effect on preventing piglet diarrhea as good as commercial recombinant vaccine.

고강도 Self-Leveling재의 최적 결합재비 (The Optimum Binder Ratio for High-Strength Self-Leveling Material)

  • 김진만
    • 한국건축시공학회:학술대회논문집
    • /
    • 한국건축시공학회 2002년도 학술.기술논문발표회
    • /
    • pp.67-76
    • /
    • 2002
  • Self-leveling material(SLM) is one of the floor finishing materials which make flat surface like as water level by itself in a short time. So it is possible to increase construction speed and enhance economical efficiency. In this study, author intended to develop SLM for the industrial warehouse and factory loading heavy weight machinery and vehicles. The demanded properties for this type of SLM are above 20mm of flow value and above 300kgf/cm2 of 28-days compressive strength. To possess demended strength and fluidity, SLM have to be composed of many types of binders and chemical additives. So it is difficult to decide suitable mixing proportion of composition materials. In this study, author investigated the weight percentage effect of main composition materials for high-strength self-leveling material, by experimental design such as tables of orthogonal arrays and simplex design, and by statistical analysis such as analysis of variance and analysis of response surface. Variables of experiments were ordinary portland cement(OPC), alumina cement(AC), anhydrous gypsum(AG), lime stone(LS) and sand, and properties of tests were fluidity of fresh state and strength of hardened state. Results of this study are showed that suitable mix proportions of binders for the high strength self-leveling materials are two groups. One is 78~85.5% OPC, 7.5~9.5% AC, 9~12.5% AG and the other is 72.5~78% OPC, 9~12.5% AC, 13~l5% AG.

  • PDF