• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 하계학술대회 논문집
• /
• pp.29-30
• /
• 2010

This paper proposed bidirectional DC-DC converter applying soft switching technique. Compared with conventional bidirectional converter, the main switches of proposed converter are operated without switching losses, and auxiliary switches were run under soft switching condition using quasi-resonant current mode. To verify the validity of the proposed converter, mode analysis and simulation results are presented.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1059-1060
• /
• 2006

In this study, vibration mode multilayer piezoelectric transformer was designed and thickness simulated using ANSYS of finite element method simulator for investigating its optimum conditions ist. As a results, resonant frequency was decreased with the increase of output layer thickness, Output voltage, maximum displacement and maximum stress at 0.34mm thickness transformer were 228.1 V, $0.42{\mu}m,\;8.78[N/m^2]$ respectively.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1087-1095
• /
• 1990

본 연구에서는 슬롯을 가지는 2차원 원형 풍동에 대하여 슬롯의 갯수, 크기와 흐름의 속동에 따른 공진 특성을 2차원 8-노드 등계수(isoparametric)요소를 사용하여 해석한다.

• 산업기술연구
• /
• 제27권B호
• /
• pp.129-135
• /
• 2007

In this paper, an modal analysis based on the distribution of the electromagnetic fields on the UWB elliptical patch-slot antenna is presented. We designed the UWB antenna by iterating the dimensional parameters of the antenna as the traditional design method. Then the antenna was carefully analyzed using 3D E-M simulator. The result of the analysis shows that the slot antenna operates on a series of the multi-pole radiations based on TE modes matched to the system impedance. This result gives us an easier method to design the similar antennas, which is the impedance matching to the system impedance after once constructing a proper structure with a series of multi-mode resonances.

• 한국광학회지
• /
• 제12권6호
• /
• pp.485-488
• /
• 2001

본 논문에서는 광섬유에 주기적인 압력을 인가함으로써 유도되는 굴절률 변화를 통해 장주기 광섬유격자를 설계하여 제작해 보았으며, 제작된 장주기 광섬유격자의 압력에 따른 투과특성과 파장가변 특성 및 편광의존성에 대해서 이론적 고찰 및 실험적 분석을 하였다. 제작된 장주기 광섬유격자의 투과량은 압력에 따라 주기적으로 변하며. 결합되는 모드의 중심파장을 180nm이상 가변할 수 있었다. 또한 모드결합의 중심파장이 9nm정도의 편광의존성을 갖는것을 확인하였다.

• 조명전기설비학회논문지
• /
• 제30권3호
• /
• pp.65-72
• /
• 2016

This paper discussed the LCL-type & Isolated bidirectional dc-dc converter(BDC) with dual full bridge inverter. In order to verify the analysis of the BDC, Experimental prototype has been designed and implemented to supply constant voltage regardless of loads and proposed a method to select switching frequency that depended on two inductors' inductance ratio and transformer parameters. The proposed converter has been composed of LCL resonant network with unit inductance ratio ($L_r/L_f$=1) and then operated with fixed duty, 50% duty ratio and fixed frequency. There are some characteristics that input voltage and output voltage of the BDC is nearly identical and zero voltage turn-on switching is possible in forward and reverse mode. Finally, it has been showed that BDC is possible to commutate operating mode normally and provide constant output voltage in selected switching frequency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.1187-1189
• /
• 2004

This paper presents a boost circuit topology driving in high - frequency. It solves the problem which arised from hard-switching in high-frequency using a period of resonant circuit and operating under the principle of ZCS turn-on and ZCZVS turn-off commutation schemes. In the existing circuit, it has the high voltage stress in free-wheeling diode. But in the proposed circuit, it has voltage stress which is lower than voltage stress of existing circuit with modifing a location of free-wheeling diode. In this paper, it explained the circuit operation of each mode and the waveform of each mode. Also the experiment result compares the existing voltage stress of free-wheeling diode with the proposed voltage stress of that.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.699-705
• /
• 2013

This paper presents vibration testing, control, and finite element analysis of a piping system, which is subjected to the changes in fluid levels. Nuclear power plants typically employ a cooling system that uses sea water. These systems are subjected to dynamic characteristic changes caused by sea-level variations, which introduces failures of cooling system components. Therefore in this study, analytical and experimental studies were performed to understand the effect of sea-level changes on the dynamic characteristics of piping systems. It was shown that, as the sea-level increases, pipe's natural frequencies decreases in relation to its mode shape. A 1/14 scale model was also built to compare the results obtained by the analytical study. A good agreement between experiment and analytical studies were observed. Finally, an on-line resonant frequency identification system was proposed and developed, which utilizes piezoelectric transducers as sensors and actuators, in order to avoid catastrophic failure of piping systems.

• Smart Structures and Systems
• /
• 제24권3호
• /
• pp.379-390
• /
• 2019

In this research, we propose an energy harvesting structure with a flexible blade element vibrating at its first mode to maximize the power output of the piezoelectric material. For this purpose, a piezoelectric patch was attached on the blade element used in a small-scale wind turbine, and air load was applied with a suitable angle of attack in the stall zone. The aerodynamic load created by air excitation vibrates the blade element in its first natural frequency and maximizes the voltage output of the piezoelectric patch. The variation of power outputs with respect to electrical resistance, air speed, and extra mass is experimentally investigated for various cases. An analytical model is constituted using a single-mode blade element with piezoelectric patch dynamics, and the power outputs of the obtained model are compared with experimental results.