• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.10
• /
• pp.703-712
• /
• 1987

A position detection method for 2 phase bifilar permanent magnet step motors is proposed. The back emfgenerated on 2 phase windings by rotor permanent magnet is calculated using motor terminal voltage and current by analog circuit, and the rotor position output is obtained from tese back emf signals through some logical manipulation circuit. This position detector functionally acts like a 2 channel optical incremental encoder, and it is also shown by experimental results that it works well over wide range of speed or under resonant condition where the rotor rings around the detent position. Its resolution is twice of the number of steps per revolution. Bu software implemented on micro-processor, the reliability of position output is enhanced, detecting and correcting error dut to external and/ or internal noise.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.111.4-111
• /
• 2001

In this paper, an adaptively tuned dynamic absorber is proposed. The adaptively tuned dynamic absorber is a dynamic absorber whose stiffness is tuned so that the natural frequency of the absorber coincides with the operating or natural frequency estimated by an adaptive algorithm. The feature of this absorber is as follows. It has an electrodynamic device for the stiffness control. Using Lorenz´s force, it changes the stiffness by changing the applied current. The change of stiffness results in the natural frequency shift, because its mass and damping coefficient are fixed. We may reduce the vibration of the overall system by tuning the natural frequency of the dynamic absorber to the resonant frequency of the structure, when the dominant single tone oscilation occurs in the system ...

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.12
• /
• pp.113-121
• /
• 1996

This paper presents a 37.5kVA (125kVp, 300mA) high frequency inverter type power supply for diagonostic X-ray generator with two HFHV (high-frequency high-voltage) isolating transformers. The output regulations, X-ray tuve voltage and tube current, are obtained by two high frequency inverters with the each other feedback PI controller and operating time switch for selecting shooting time and synchronizing two inverters. The operating modes and design consideration of the proposed power supply are given. Issues in the design of two HFHV isolating transformersfors high volage genrating and filament heating are discussed. Experimental results are presented to verify the performance of the designed power supply for varying load conditions. The proposed apparatus has several advnatages, e.g., the fast rising time of tube voltae, accuracy and reduced component size etc.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.289-292
• /
• 2007

The modular line-connected photovoltaic PCS (power conditioning system) is proposed. The proposed system consists of a step-up DC-DC converter and a full-bridge inverter. A step-up DC-DC converter using a dual series-resonant rectifier circuit and a active-clamp circuit is proposed to achieve a high efficiency and a high input-output voltage ratio efficiently. An IncCond (incremental conductance) MPPT (maximum power point tracking) algorithm that improves MPPT characteristic is used. By control a inverter using a linearized output current controller, a unity power factor is achieved. All algorithms and controllers are implemented on a single-chip microcontroller and the superiority of the proposed algorithms and controllers is proved by experiments.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.136-139
• /
• 2004

This paper presents a buck circuit topology of high-frequency with a single switching element. It solved the problem which arised from hard-switching in high-frequency using a resonant snubber and operating under the principle of ZCS turn-on and ZVS turn-off commutation schemes. In the existing circuit, it has the voltage stress which is twice of input voltage in free-wheeling diode. But in the proposed circuit, it has voltage stress which is lower than input voltage with modifing a location of free-wheeling diode. In this paper, it explained the circuit operation of each mode and confirmed the waveform of each mode with simulation result. Also the experiment result verified the simulation waveform and compared the existing voltage stress of free-wheeling diode with the proposed voltage stress of that. Moreover, it compares and analyzes the proposed circuit's efficiency with the hard-switching circuit's efficiency according to the change of load current.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1010-1011
• /
• 2015

최근 고효율 전력변환을 위해 LLC 공진형 하프브릿지 컨버터의 동기정류기에 대한 연구가 활발히 진행되고 있다. 기존 일반적인 다이오드 정류기를 사용하는 경우 출력전류에 비례하는 전력손실이 커서 대전력용으로 사용하기에는 적합하지 않다. 따라서 스위치를 이용한 동기정류기가 검토되고 있는데 동기정류기의 스위치를 구동시키기 위해서는 스위치를 구동시킬 수 있는 구동용 IC가 이용되고 있다. 동기정류기 구동 IC의 단점으로는 약 50%의 중부하 이하에서는 동작되지 않는 단점이 있어 이를 보완하기 위하여 변압기 1차측 전류를 검출하여 게이트 전압을 만들어 스위치를 구동시키는 회로를 제안하였다. 본 논문의 실험 결과 저전력 지점에서 동기정류기가 구동되었고 따라서 전력변환 효율은 기존의 다이오드 정류기에 비해 우수하며 효율개선효과가 있다는 것을 실험으로 보였다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.13-16
• /
• 2000

This paper describes a design of the external-exciting electronic ballast for 100W high pressure sodium lamp. The ballast is consists of the full-bridge inverter and an external-exciting control circuit. L and C values of an equivalent L-C series resonant circuit are calculated analytically. The electrical output characteristics of the ballast, such as voltage, current etc., are simulated by Pspice. The experimental results from high pressure sodium lamp system with the ballast we developed are shown to be consistent with the simulated results.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.111-115
• /
• 2000

In this paper, a prototype electronic ballast for 400W MH lamps is designed and implemented. To remove the phenomenon of acoustic resonance in the lamp being operated at high frequency, a spread spectrum method is employed on the ballast. Half-bridge resonant inverter, voltage-controlled-oscillator and PFC are used and the current of lamp is controlled with taking into account the voltage of lamp. The ballast is built with analog OP-amps and MOSFETs. The experimental results show the good performance as PF 0.93, ATHD 0.14, Ballast loss 22W at output 400W.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.357-360
• /
• 2008

In this paper a high efficiency soft switching boost converter is proposed for photovoltaic system. Using some resonant components, the circuit can be achieved the soft switching capability. Each of the switches in the proposed circuit performs ZV (Zero Voltage) or ZC (Zero Current) switching. Thus, the high efficiency characteristic can also be obtained, and then the size of the total system can be reduced. The operational modes of the verifying the effectiveness of the proposed circuit. As a matter of course, we will present the simulation results in this paper.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.325-328
• /
• 2008

This paper presents a new conceptual electromagnetic induction eddy current-based stainless steel plate spiral type heater for heat exchanger or dual packs Heater in hot water system boiler steamer and super heated steamer, which is more suitable and acceptable for new generation consumer power applications. In addition, an active clamped quasi resonant PWM high frequency inverter using trench gate IGBTs power module can operate under a principle of zero voltage soft commutation with PWM is developed and demonstrated fora high efficient induction heated hot water system and boiler in the consumer power applications This consumer induction heater power appliance using active clamp soft switching PWM high-frequency inverter is evaluated and discussed on the basis of the simulation and experimental results.