• Journal of the Korean Institute of Telematics and Electronics
• /
• v.15 no.3
• /
• pp.30-34
• /
• 1978

A bridge inverter circuit with a paralled resonant circuit load is analyzed. The approach to the circuit analysis leads to reasonable reality. The limit of trigger frequency, the range of SCR turn-off time, the peak capacitor voltage and the relation between the load current and trigger rate are derived for the suitable design criteria. Numerical method is used for calculation of transcendental equation.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.221-224
• /
• 1998

A PWM inverter with an induction motor often has a problem with a high-frequency leakage current that flows through the distributed electrostatic capacitance from the motor windings to ground. This paper presents an equivalent circuit for high-frequency leakage currents in PWM inverter feeding an induction motor, which forms an LCR series resonant circuit.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.382-385
• /
• 2002

In this paper, an improved ZCS-PWM boost converter is proposed to minimize conduction loss by flowing resonant current only through the auxiliary circuit. The operation principle of the proposed converter is explained and design procedure is established. Experimental results are presented to verify the theoretical analysis.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.625-630
• /
• 2005

In this paper, several energy recovery circuits (ERC) for the plasma display panel (PDP) are reviewed and classified in a manner of operation characteristics. A typical ERC using the Regenerative Transformer (RT) is introduced and compared with conventional ones. RT-ERC can achieve zero-voltage-switching (ZVS) for main full-bridge switches and zero-current-switching (ZCS) for the resonant switches and diodes. The charging/discharging energy of panel capacitance is efficiently recovered with the RT and without a sub-circuit. The presented circuit is verified with simulation and experimental results.

• Proceedings of the IEEK Conference
• /
• 2003.11c
• /
• pp.327-330
• /
• 2003

A novel compact circular polarization operation of the microstrip antenna with four-slits and T-slits is proposed. The mechanism for compact size antenna is investigated with the behavior of the currents on the radiating patch. The equivalent surface current path due to the slits is lengthened, reducing the resonant frequency at a fixed patch size. The proposed compact CP design can have an antenna size reduction of about 33 ∼ 45％ as compared to the conventional microstrip antenna. Details of the experimental and measured results are presented and analysed.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.295-296
• /
• 2013

본 논문에서는 새로운 전류원 공진형 컨버터를 제안한다. 제안한 컨버터는 입력전류 리플이 작으며 모든 스위치와 다이오드의 ZCS 턴온/턴오프를 성취하며 턴온/턴오프 전류의 di/dt가 0이다. 또한, 인터리빙 시 출력전류 리플을 이론적으로 완전히 제거할 수 있다. 제안하는 컨버터의 동작원리를 제시하고 실험을 통하여 타당성을 검증하였다.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.7
• /
• pp.39-47
• /
• 1992

This paper showed that theoretical site attenuation curves were obtained simply by the method of moments analysis for current integral equations on antennas. Since the expansion coefficients of driving and receiving points were calculated from the method of moments procedure, site attenuations were evaluated simply using these basic antenna parameters. Theoretical site attenuations were calculated with half-wave resonant dipoles connected directly to a 50 ohm receiving system and connected to a 72/50 ohm matching network, respectively. Results were compared with other theoretical studies reported so far. Also included were experimental results for site attenuations to prove the validity of theoretical analysis.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.3129-3131
• /
• 1999

The electronic ballast for MHD lamp was studied for automotive headlight application. Its basic principle is the Current Sourcing Push-Pull Resonant Inverter with DC I2Volt input Voltage. By changing the switching frequency according to the lamp state, the automotive requirement of very fast warm-up and the zero voltage switching condition were shown by the simulation of the ballast circuit.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.34-36
• /
• 2008

This paper is given a full detail of mathematical analyses of input current for novel active type power factor correction(PFC) AC-DC converter of step up-down added electric isolation. These are compared with harmonics components of input current for a conventional PFC converter of electric isolation type. The proposed PFC converter is constructed in using a new loss-less snubber circuit to achieve a soft switching of control device. Also the proposed converter for discontinuous conduction mode(DCM) eliminates the complicated circuit control requirement and reduces the size of components. The input current waveform in the proposed converter is got to be a sinusoidal form of discontinuous pulse in proportion to magnitude of ac input voltage under the constant duty cycle switching. Therefore, input power factor is nearly unity and the control method is simple. Particularly, the stored energy of loss-less snubber capacitor is recovered with input side and increases input current from resonant operation. The result is that input power factor of the proposed converter is higher than that of a conventional PFC converter. Some simulative results on computer and experimental results are included to confirm the validity of the analytical results.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.507-515
• /
• 2013

This paper proposes a compensation method for the $2^{nd}$-order harmonic of single-phase grid-connected wind power generation systems. Theoretically, a single-phase grid-connected inverter system has no choice but to cause the $2^{nd}$-order harmonic to DC-link voltage. The reference active current is affected by the DC-link voltage. The output current from the reference active current is distorted by the $1^{st}$ and $3^{rd}$-order harmonic. The proposed method can compensate, conveniently, the reference active current with the $2^{nd}$-order harmonic. To reduce the $2^{nd}$-order ripple in the reference active current, proposed method takes a PR controller as a feed-forward compensator. PR controllers can implement selective harmonic compensation without excessive computational requirements; the use of these controllers simplifies the method. Both the simulation and experimental results agree well with the theoretical analysis.