• Journal of Power Electronics
• /
• 제19권4호
• /
• pp.1034-1044
• /
• 2019

In medium-voltage and high-voltage high-power converters, the switching devices need to operate at a low switching frequency to reduce power loss and increase the power capacity. This increases the delay of the signal sampling and PWM. It also makes the cross-couplings of the d-q current components more severe. In addition, the LCL filter has three cross-coupling loops and is prone to resonance. In order to solve these problems, this paper establishes a complex vector model of an LCL type grid-connected converter. Based on this model, two multiple decoupling current control strategies with passive damping / notch damping are proposed for the LCL type grid-connected converter. The proposed strategies can effectively eliminate the cross-couplings of the converter, achieve independent control of the d-q current components, expand the stable region and suppress the resonance of the LCL filter. Simulation and experimental results verify the correctness of the theoretical analysis and the feasibility of the proposed strategies.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.286-292
• /
• 1993

The classical way to improve the control performance is studied on the aspects of gun/turret deive systens. Two ways are discussed comparadively ; electrical case and electro-hydraulic case. System parameters are analytically studied in terms of resonance frequencies, and damping and gear train ratio effects are checked in relation to resonance frequency increase. Benefit of the feedback is discussed to increase the damping of the natural frequency lending to bandwidth increase.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.319-323
• /
• 2000

A method for miniaturization of microstrip patch antenna without degrading its radiation characteristics is investigated. The ring geometry introduces additional parameters to the antenna that can be used to control its resonance frequency and bandwidth. For a single square ring increasing the size of patch decreases the resonance frequency and bandwidth. To match the antenna to a transmission line and also enhance its bandwidth. the square ring patch is stacked by a square ring patch. The computed results are compared with experiment and good agreement is obtained.

• 대한치과보철학회지
• /
• 제43권6호
• /
• pp.745-750
• /
• 2005

Statement of problem. Resonance frequency analysis has been increasingly served as a non-invasive and objective method for clinical monitoring of implant stability. Many clinical studies must be required for standardized data using RFA. Purpose. This study was performed to evaluate RFA value changes in two anodized implant groups. Material and method. Among a total of 24 implants, twelve screw shaped implants as a test group (H2-R8.5) were manufactured, which had a pitch-height of 0.4 mm, an outer diameter of 4.3 mm, a length of 8.5 mm, and external hexa-headed, were turned from 5 mm rods of commercially pure titanium (ASTM Grade IV, Warantec Co., Seoul, Korea), and another twelve implants as a control group were $Br{\aa}nemark$ Ti-Unite MK4 (diameter 4.0 mm, length 8.5 mm). Each group was installed in tibia of rabbit. Two implants were placed in each tibia (four implants per rabbit). Test two implants were inserted in right side and control two in left side. ISQ values were measured using $Osstell^{TM}$ (Integration Diagnostics Ltd. Sweden) during fixture installation, and 12 weeks later and evaluated the RFA changes. Results. Mean and SD of baseline ISQ values of test group were $75.0{\pm}3.4$ and $68.7{\pm}8.1$ for control group. Mean and SO of ISQ values 12 weeks after implant insertion were $73.2{\pm}4.7$ for test group and $72.6{\pm}3.9$ for control group. There were no statistically significant differences between groups in ISQ values after 3 months (P>0.05). From the data, RFA gains after 3 months were calculated, and there was statistically significant difference between groups (P<0.05). Conclusion. Although there were RFA changes between groups, implant stability after experimental period shows alike tendency and good bone responses.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제30권5호
• /
• pp.417-427
• /
• 2008

The aim of this study is to investigate the effect of anodizing surface to osseointegration of implant by using of resonance frequency analysis (RFA), quantitative and qualitative assessment of an anodically modified implant type with regard to osseous healing qualities. A total of 96 screw-shaped implants were prepared for this study. 72 implants were prepared by electrochemical oxidation with different ways. 24 (group 1 SP) were prepared at galvanostatic mode in 0.25M sulfuric acid and phosphoric acid. 24 (group 2GC) were prepared at galvanostatic mode in calcium glycerophosphate and calcium acetate and 24 (group 3 CMP (Calcium Metaphosphate) Coating were prepared at galvanostatic mode in 0.25M sulfuric acid and phosphoric acid followed by CMP coating. Rest of 24 (control group were as a control group of RBM surface. Bone tissue responses were evaluated by resonance frequency analysis (RFA) that were undertaken at 2, 4 and 6 weeks after implant placement in the mandible of mini-pig. Group 1 SP (anodized with sulfuric acid and phosphoric acid implants) demonstrated slightly stronger bone responses than control Group RBM. Group 2 GC (anodized surface with calcium glycerophosphate and calcium acetate implants) demonstrated no difference which were compared with control group. Group 3 GMP (anodized and CMP coated implants) demonstrated slightly stronger and faster bone responses than any other implants. But, all observation result of RF A showed no significant differences between experimental groups with various surface type. Histomorphometric evaluation demonstrated significantly higher bone-to-implant contact for group 2 GC. Significantly more bone formation was found inside threaded area for group 2 GC. It was concluded that group 2 GC (anodized surface with calcium glycerophosphate and calcium acetate implants) showed more effects on the bone tissue responses than RBM surface in initial period of implantation. In addition, CMP showed a tendency to promote bone tissue responses.

• 제어로봇시스템학회논문지
• /
• 제18권6호
• /
• pp.546-554
• /
• 2012

This paper suggests a design method of an improved phase control loop for tracking resonant frequency of solid type precision resonant gyroscope. In general, a low cost MEMS gyroscope adapts the automatic gain control loops by taking a velocity feedback configuration. This control technique for controlling the resonance amplitude shows a stable performance. But in terms of resonant frequency tracking, this technique shows an unreliable performance due to phase errors because the AGC method cannot provide an active phase control capability. For the resonance control loop design of a solid type precision resonant gyroscope, this paper presents a phase domain control loop based on linear PLL (Phase Locked Loop). In particular, phase control loop is exploited using a higher order PLL loop filter by extending the first order active PI (Proportion-Integral) filter. For the verification of the proposed loop design, a hemispherical resonant gyroscope is considered. Numerical simulation result demonstrates that the control loop shows a robust performance against initial resonant frequency gap between resonator and voltage control oscillator. Also it is verified that the designed loop achieves a stable oscillation even under the initial frequency gap condition of about 25 Hz, which amounts to about 1% of the natural frequency of a conventional resonant gyroscope.

• Journal of Electrical Engineering and Technology
• /
• 제1권3호
• /
• pp.332-337
• /
• 2006

In this paper, an electronic ballast was developed to control a 250W metal halide lamp. To avoid acoustic resonance phenomenon, we calculated the acoustic resonance band and determined the driving frequency from 70kHz to 100kHz. Due to the switching loss of MOSFET, many problems are caused in the inverter circuit during lamp lighting, so we reduced the loss by connecting the capacitor that minimizes the magnitude of the impulsive voltage. In this paper, the main point of research is to find the methods to operate the lamp on the rated output power. After detecting the current and the voltage of the lamp, we changed the driving frequency by adjusting the DC voltage level of the VCO input.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권2호
• /
• pp.184-189
• /
• 2014

In this paper, a new design method of vibration suppression controller for multi-inertia (especially, 3-ineritia) resonance systems is proposed. The controller consists of a digital fuzzy controller for speed loop and a digital PI controller for current minor loop. The three scaling factor of the fuzzy controller and two PI controller gains are determined by Differential Evolution (DE). The DE is one of optimization techniques and a kind of evolutionary computation technique. In this paper, we have applied the DE/rand/1/bin strategy to design the optimal controller parameters. Comparing with the conventional design algorithm, the proposed method is able to shorten the time of the controller design to a large extent and to obtain accurate results. Finally, we confirmed the effectiveness of the proposal method by the computer simulations.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.483-488
• /
• 2001

In the present study a numerical simulation is performed on a natural convection inside a square cavity with a vibrating wall. The study has been conducted varying the heat transfer rate, wall excitation frequency and also the orientation of the cavity. The temperature and velocities inside the cavity was observed and also, the heat transfer coefficients on the heating wall was seen. From the results, it can be seen that the temperature inside the cavity decreases when excited with the proper frequency and the heat transfer coefficient increased with cavity inclination angle, ${\theta}$. It is also found from the results that flow resonance is occurred near the inclination angle ${\theta}=90^{\circ}$.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.865-868
• /
• 2005

A Helmholtz resonator is one of noise control elements widely used in many practical applications. The resonator has very high absorption at resonance frequency but the frequency bandwidth is very small. Therefore many kinds of additional resistive screens have been applied to the resonator's neck in order to increase the bandwidth. This paper discusses the absorptive characteristics of a Helmholtz resonator damped by a flexible porous screen in form of wire mesh. First, various experimental results are introduced and studied. Secondly, the effect of the resistive screen is theoretically predicted. It is shown that the distance between the screen and aperture affects on the resonance frequency as well as the absorption of the system.